Find a Driveway Installer you can trust in Woodstock.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

If you’re considering laying gravel on your driveway, then you’d probably want to know the amount of gravel you’ll need to complete the project. When you are calculating the amount of gravel you’ll require to cover your driveway, there’s an important factor you’ll need to consider and that is the type of gravel you opt for such as a crushed or pea gravel. There are varying grades which are found in particles from fine to course, with a size ranging from 2mm to 64mm. Therefore, there’s a need to estimate the volume of the gravel while also having the rock’s size in mind. Also, there’s a need to select your most preferred gravel which you’ll like to use before proceeding to dig the depth of your driveway and subsequently determine the amount of gravel that’ll be needed using these excellent tips.

✓ Determine the size and coverage. As you would have expected, the smaller the gravel is, the bigger the coverage will be, and gravels should be at least 4 inches deep. However, if the rocks happen to be a bit large then you can allow for an extra 1/2 inch.

✓ Measure the driveway. Multiply the width by the length and depth to get the size of the driveway in cubic feet. Meanwhile for cubic yards, you can divide the total cubic feet by 27. This is due to the fact that one cubic feet is same as 1.13 tons.

✓ Working with gravel. Here, you’ll have to calculate an underlay measurements differently. You can use 2 inches of road base that’ll be overlaid with 2 inches of gravel.

While resin bound and resin bonded driveways have similar names, it might surprise you to know that they’re very different. Both paving systems use resin and aggregates (stones) to form a fixed surface, but there are plenty more differences than there are similarities.

Resin bound driveways are made from a resin and aggregate mix that is trowelled onto a bitmac or concrete base. It leaves a smooth, flat finish and you won’t find any loose gravel. It’s also a pourous surface, which means that rainwater can pass through into the ground, avoiding pools and flooding.

However, resin bonded driveways involve spreading resin across a base, then scattering aggregate into it. Most of the stones will stick to the resin, but some will stay loose. That means you’ll get the effect of loose gravel without so much to sweep and take care of. Because the stones are scattered onto a complete layer of resin, water can’t pass through it. That means you could end up with water pooling, and it also means that a resin bonded driveway isn’t frost resistant, meaning it could get slippery.

So which is better – a resin bound or resin bonded driveway? The answer depends on a few things. If you have a period property where a smooth, shiny surface might not complement the look of your home, you might want to go for resin bonded. If you need lots of grip, for example if you’re a wheelchair user, resin bonded may also be the way to go – even though resin bound surfaces still offer enough grip for sloped driveways and ramps. But if you want a low-maintenance, weed-free, permeable surface, resin bound driveways are the way to go.

From gravel and crushed stones to asphalt and tarmac, the choice when it comes to surfacing options for driveways is truly staggering. However, what’s not too clear is the options that best suits a sloping driveway. If you also possess a sloping driveway and wondering the best material to install, you’re definitely not alone. This is a major source of concern for several home and property owners in the UK being fully aware that making the wrong choice here can prove really costly and disastrous. In order to help you make the best informed decision possible, we’ve put together this post which takes a look at the various driveway material options available to you.

• Gravel
  This driveway surfacing option provides a truly enjoyable “crunch sound when driven on, however, the satisfaction will be short lived if installed on a sloped driveway. If installed on a sloped driveway, there’s going to be a continual displacement as instinctively rolls downhill on an incline.

• Concrete
  This can prove to be a great problem if installed on an incline. This is due to the fact that concrete is subject to freeze/thaw phenomenon which makes it steep and slippery lacking the needed traction.

• Tarmac
  This is particularly far from ideal when it comes to a steep driveway surface. This is because it requires continuous maintenance to prevent spillages from spoiling the surface.

• Resin
  The best surface for a steep driveway is simply that made from resin. This is due to the fact that this surfacing option allows water to soak away naturally. They’re perfectly permeable, preventing water from pooling and reducing the risk of falls.

From concrete paving to material bound and also obstruct paving, there are a plethora of hard surfacing system alternatives readily available on the market today. Nevertheless, one of the alternatives that really stands out is the Indian stone appearing. The Indian stone is not just distinguished for its variety colour profiles and also reduced maintenance requirements, however its additionally understood to be really budget friendly when contrasted to various other comparable high-end appearing alternatives like Yorkshire paving. The Indian stone paving is always among the very best when it comes some top qualities such as strength, resistance, structural in addition to its visual benefits. In this post, we'll be checking out a lot of reasons that you need to consider getting an Indian stone paving mounted on your driveway. Let's have a look!

• Visually appealing. If the look of your driveway is just one of your top concerns after that you'll hardly get many better choices than Indian stone paving. This kind of difficult emerging comes with a wide range of stunning colours you can choose from to make your landscape appear like heaven in the world.
• Little maintenance. Indian stone driveway calls for just a marginal maintenance as most of the dirt built up over time will be gotten rid of by water, while you can easily pipe down the few continuing to be ones. It's truly that simple!
• It's durable as well as safe. As a result of the high percentage of quartz, the Indian stone paving is very durable. It makes an exemplary material that can hold up against all type of pressure. Not only is it resistant to weather extremes, however it additionally won't get harmed because of lots of foot or cars and truck traffic.
• Inexpensive. As a result of its many benefits, it might actually look like an unique material, however you will not have to break the bank to install it.

Gravel is the cheapest driveway surfacing material. Asphalt costs a little more than gravel, and concrete is significantly more expensive. The cost of paving depends on the material you use. Obtain as many quotes as possible as materials and costs differ from company to company.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.

• Where in the country you live
• What colour you choose
• What pattern you choose
• Whether you choose a standard or a higher-quality concrete