Find a Driveway Installer you can trust in Taunton.

If you’re considering getting a new tarmac driveway or outside area, it’s important to know how long it takes to dry. Try to use it too early and you might damage it and ruin its appearance.

It won’t be long before you can walk on your new surface, as long as you’re careful. However, it’s a good idea to avoid putting heavy objects or driving on it for 2-3 days. For a more accurate timescale, ask your tarmac paving and driveway pro.

Some paving projects require you to cut paving slabs to make them fit into a smaller space. To do this, firstly you need to measure the slab and draw a line in pencil or chalk where you want to cut.

There are then several different ways you can cut the slab – you or your professional can choose the one you or they are most happy with. A hammer and chisel can work well, or a handheld saw. You can also use an angle grinder fitted with a stone-cutting disc.

Being a fantastic alternative to slabs or block paves, gravel drive way slowly becoming an extremely popular driveway surfacing option in the UK. Not only does gravel driveway value adding investment to a home, but also allows you to be very creative and can make a beautiful addition to your home.

It’s normal to think that having a new gravel laid is a herculean task but when the necessary tools and materials are within your reach then it’s a fair simple task for the competent DIYer. So if you’re about to lay your new gravel driveway option of your home and wondering how deep to dig the driveway, then you’ve come to the right place. There are times, however, that the best option would be to hire a reliable and trustworthy professional who can guarantee the best results while also helping you save time and additional expenses which could result from costly mistakes. However, in this guide, we offer some handy tips on the appropriate depth of a gravel driveway in order to put you on the right path from the start. So let’s take a closer look!

Normally, it’s required to lay a a 10 mm aggregate on a depth which should be within the range of 30 mm to 40 mm. However in the case of driveway, this structure must be at least 50mm deep. As a result of this requirement, you’ll require to dig a minimum depth of about 50 mm to 60mm on your driveway. If you’re using a larger aggregate, it’s going to settle and bond together more easily than the smaller alternatives. Therefore, the depth of your driveway will mostly be determined by the size of the aggregate you opt for as well as how you intend to use the surface.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

Tarmac is a material made up of broken stone and tar, used for surfacing roads, driveways and other outdoor areas. It’s actually a registered product trademark, but many people use ‘tarmac’ interchangeably with ‘asphalt’. Asphalt is similar to tarmac, but is now more commonly used, and is made from bitumen instead of tar.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

Have you decided to install block paving and wondering what the best sand to be applied to the joints is in order to achieve a perfect job? Well, you’re at the right place! This is one of the most frequently asked questions when it comes to block paving and we seek to give you a reliable solution once and for all.

The best sand for block paving is a kiln-dried sand. It’s an extremely fine sand which has been dried in a kiln to get rid of all the water before it’s incorporated to achieve the best results. Therefore, the sand contains no moisture and is commonly used to fill the joints of block paving to keep the paving’s structure rigid and strong. It also goes a long way to prevent the ingress of water while stopping the paving from moving and becoming loose. The major reason why the paving sand must be dried is to allow it flow easily into the joints as well as the block paving’s gaps. As result of this smooth flowing to the bottom of the joints, there will be no sand sticking to the sides of the pavers.

Another major reason why kiln-dried sand is commonly applied to the block paving’s joints is to prevent water from penetrating the paved area. It also tightens the individual pavers together to prevent from moving and becoming loose. In the event whereby you happen to leave the joints of your block paving without kiln dried sand, it’s highly likely that they’ll sink as a result of water penetration and the blocks will become very loose. After washing block paving, it’s very important to also replace any sand washed off in the process once the paving is dried to prevent water ingress into the joints.