Find a Driveway Installer you can trust in Wallington.

There’s no doubt that weeds coming through your block paving can be unsightly and annoying. But, it’s relatively easy to get rid of weeds that are growing in the joints between your block paving. To start, pull out the larger weeds, and then you can use a pressure washer or firm bristled brush to remove the smaller weeds and debris from the joints in your block paving. It’s best to then refill the joints with additional sand to ensure your block paving remains level. Regularly brushing your block paving and treating with weed killer will help to prevent the weeds from reoccurring.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

It’s always a good idea to be sure of how you’re going to keep the annoying gravel spillage off your driveway way before its installation, however, if you’ve already done so, it’s better late than never. We all know how great a gravel driveway can look when the gravels manage to stay in place. When gravel is used on a driveway it provides a great transition from the normal hardness of a driveway to the organic softness of the lawn which doesn’t retain water or gush runoff during irrigation or rainfall. Unfortunately, the sad thing here is gravel don’t just like to stay put. Before long, if ignored, you’d realize your hard surfaces will almost be covered with gravel coming in from the side. So what’s the solution to this rather annoying situation?

Here, we’ll show you just how you can keep your gravel in place in your driveway. Let’s take a look!

The solution here is simple - simply make use of Pour On. With Pour On, you won’t have to think about of clearing out your gravel features to put an end to the issue of loose rocks spilling on your hard surfaces. With Pour On, you’ll be able to hold your gravel in place for several years to come. And even more importantly, it’s able to achieve this objective while also protecting the integrity the existing permeability of your driveway. What’s more? It also goes a long way to retain the natural look provided by your gravel driveway which makes it the perfect solution to the annoying gravel spillage issues.

1. Prepare the sub-baseThe driveway company will excavate, or dig, the existing surface down to a depth of around 200mm. They will remove any debris from the area may place it in a skip or arrange for it to be removed in another way. When they dig down to the sub-base of your previous driveway, they will assess how much hardcore they need and arrange for that to be delivered to the site. They will then spread the hardcore across the sub-base to create a level surface to pour the concrete on. Most good contractors will apply a gel to any walls and doors to protect them from concrete splashes. They will also add any gulley tops, manhole covers or shuttering that’s required.
2. Installation and imprintingNext, the tradespeople will have the concrete either poured from a large mixer vehicle or barrow it in from a mixer and pour onto the surface. They level it with rakes, then add a colour surface hardener in a colour of your choice. This will give the driveway its permanent colour. They will then wait until the concrete has hardened to the correct consistency for imprinting the pattern, then will use special tools and stencils to make the pattern that you asked for. They will then spread a colour powder called a release agent over the surface, and leave to dry for 1 to 2 days depending on the weather conditions.
3. CleaningWhen the contractors return, they will add crack control cuts into the concrete. This is important because concrete expands and contracts in the heat, so there needs to be some give to stop any larger cracks from forming. Then everything is power washed clean, and a chemical wash is also used on the concrete to ensure it’s completely dust-free. The installers will ensure all your walls and doors are clean, which will hopefully be an easy job if they used wall gel.
4. SealingThe final step is to seal the driveway. There needs to have been at least two dry days before the tradespeople can do it, so you might find it’s best to have your pattern imprinted driveway installed in the summer. The contractors will blow any debris away from the surface and dry any damp areas where necessary. They will then add an anti-slip agent to the sealant and brush it on. It’s best to not walk or drive onto your new concrete driveway for about 4 days after sealing to allow everything to set. But after that, you’re ready to use your new driveway!

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

Removing oil from block paving can be tricky, and a professional clean and re-point is often the best option. However, for small stains, especially recent ones, it’s worth attempting to clean it yourself. To do this, you can purchase oil remover or driveway cleaning solutions – although be careful, as some may stain or mark certain kinds of paving stones. In general, stay away from acid based cleaners.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.