Find a Driveway Installer you can trust in Bo'ness.

Driveway work is usually done in the warmer half of the year. This is partly to avoid bad weather. If you want to get ahead and avoid waiting for a contractor to be free, you should try getting in touch with a professional in the early spring so a date can be booked for install as soon as practically possible.

As a homeowner, your home is your haven where you can control things and add more value, however that doesn’t give you the license to go around digging up your driveway as you deem fit. Replacing your old driveway with a new one comes with its own unique set of rules which are put in place to ensure that your personal preferences doesn’t pose long term issues such as flooding or poor visibility on any adjoining road. You should however note that it’s not every time you would need a planing permission for your driveway.

Below are the circumstances whereby you’ll need to submit an application before commencing your driveway paving project.

• In the event whereby you are to pave a driveway of over 5 square metres and/or a permeable surface is not available for its drainage. If the later is not available, there’ll be an increase in the flood risk. As a result, there’s the need to take into account permeable paving for your project.

• In the event whereby you’re changing the visibility on your road. These situations include removal of trees, gates or walls and the like. So far your changes negatively affects drivers’ visibility, you’ll need a planning permission.

• In the situations whereby you need to include a drop kerb. You may plan to add in a drop kerb if you’re thinking about expanding your driveway. Therefore, since residents can’t change the roads or pavements at their first fanciful impulse you’ll need to consult your local council before submitting your application.

• In the situation whereby its a listed building. Planning decisions are also greatly affected by the need to protect historic building. So if your building is a listed one, you’d have to submit an application before making changes.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Clearing snow from a gravel driveway can be tricky – you need to remove the snow without taking the gravel with it.

If the snow’s quite light and dry, try using a leaf blower. You might find that this is enough to get the snow out the way. If it isn’t, start by using a shovel. Use this to clear the top layer of snow off your driveway, leaving about an inch behind. Then, use a rake to remove most of the remaining snow. This won’t take away 100% of the snow or leave all of your gravel in place, but it’s still pretty effective. You can then lay salt to melt away the rest of the snow and stop it turning into ice.

Have you decided to install block paving and wondering what the best sand to be applied to the joints is in order to achieve a perfect job? Well, you’re at the right place! This is one of the most frequently asked questions when it comes to block paving and we seek to give you a reliable solution once and for all.

The best sand for block paving is a kiln-dried sand. It’s an extremely fine sand which has been dried in a kiln to get rid of all the water before it’s incorporated to achieve the best results. Therefore, the sand contains no moisture and is commonly used to fill the joints of block paving to keep the paving’s structure rigid and strong. It also goes a long way to prevent the ingress of water while stopping the paving from moving and becoming loose. The major reason why the paving sand must be dried is to allow it flow easily into the joints as well as the block paving’s gaps. As result of this smooth flowing to the bottom of the joints, there will be no sand sticking to the sides of the pavers.

Another major reason why kiln-dried sand is commonly applied to the block paving’s joints is to prevent water from penetrating the paved area. It also tightens the individual pavers together to prevent from moving and becoming loose. In the event whereby you happen to leave the joints of your block paving without kiln dried sand, it’s highly likely that they’ll sink as a result of water penetration and the blocks will become very loose. After washing block paving, it’s very important to also replace any sand washed off in the process once the paving is dried to prevent water ingress into the joints.

Gravel driveways are very popular in the UK for a reason. Not only do they provide a more natural look than other driveway surfacing options and happens to be quite affordable, but they’re also very easy to install and maintain. And more importantly, they have a great range of colour scheme to match and compliment your brickwork and plants to make for an alluring outdoor living space.

Are you also planning to install a gravel driveway? You’ve come to the right place! If you’re a competent DIYer with confidence, then this should be as easy as they come. If otherwise, then it’s advisable to hire a reliable professional who can guarantee the best results for help. In this guide, we’ll shed more light on the gravel driveway installation process. Let’s get started!

✓ Prepare the floor. To get a level and flat floor, you’ll have to clear the area of all weeds, paving slabs, block paving etc. Get a good foundation material to apply to the surface if you have an uneven surface or if you have potholes to fill.

✓ Stop the weeds. You’ll have to apply an anti-weed membrane so you won’t have stubborn weeds growing through your finished driveway.

✓ Spread the gravel. In the process of purchasing your gravel, ensure to select handy bags, bulk bags if tipped loose. If you go for the bags there may be a need of wheelbarrow to help move the gravel around, however with a tipped loose you can have the gravel chippings tipped directly on to the driveway.

✓ Make use of the hose. It’s possible that when your gravel arrives, it’ll be be dusty. Make use of an hose to run over the driveway to bring out the true colours of your driveway.