Find a Plasterer you can trust in Great Missenden.

There are several different kinds of plastering. ‘Dot and dab’ refers to a base layer of plasterboard which is attached to a wall using ‘dabs’ of adhesive. ‘Floating’ is a technique where a backing or undercoat plaster is applied to walls. ‘Skimming’ or ‘reskimming’ refers to the very thin final decorative layer of plaster.

Can You Plaster Over Tiles?

Yes, it’s absolutely possible to plaster over tiles but just because is possible doesn’t mean you should. Plastering over tiles is an option but it’s not recommended by experts due to several reasons. A good example is the fact that a tiled environment is in no way a suitable environment that can serve as a good bonding surface for a plaster. For the success of a plastering project, there’s the need for the surface to be able to bond to the PVA base coat. Due to fact that most tiles are slippery in nature and also lack of the ability to be able to absorb moisture, the PVA base coat layer will not be able to bond to the tiled surface, which will ultimately make for a weak surface upon the application of the plaster. Consequently, the plaster will easily flake and fall from the wall.

The inability to drill into the tiled wall surface after plastering is one of the major disadvantages that also arises when you decide to plaster over tiled surfaces. Most tiled surfaces are found in kitchens and bathrooms which are going to need appliances such as sinks, lavatories, kitchen counters and lots more. These appliances are designed to be installed on solid surfaces which would not be an easy task to carry out on tiles knowing there would definitely be great cracks or damages.

The best tip you’ll get if you’re considering to plaster on a tiled surface, is that detaching tiles from a surface can easily be done with a hammer and chisel, and that would save you a host of problems later in the future. However, if you still wish to plaster on your tiled walls, then you best bet would be to get a Blue Grit bonding agent. It works better than PVA and only needs one coat.

What Is Plaster Made Of?

Plaster is one of the most commonly used materials when it comes to building construction. It’s a crucial component that’s incorporated in coating walls, ceilings as well as partitions and it hardens on drying. Plastering is one of the most ancient building materials which has taken over mud to plaster reed or sapling huts so as to serve as a protection against the elements. Here, we’re going to take a look at the multiple compositions of plaster. These components are very important due to the fact that they form a protective coating on whatever they are used on. They work to protect surfaces such as ceiling and underlying walls from scratches or any form of damage.

Plaster comprises a few materials which includes gypsum, lime or cement and all operates in a similar way. Gypsum is made of calcium sulfate dihydrate and it’s the main component of main forms of plaster, sidewalk chalk, blackboard, drywall and more. Meanwhile, lime plaster is made up of sand, water and lime ( mostly non hydraulic hydrated lime). And lastly, cement which is a mix of suitable plaster, portland cement, sand as well as water.

The plaster is usually produced as a dry powder which is mixed thoroughly with water to create a stiff but also a paste that’s workable immediately before it’s applied to the wall or ceiling.

It’s quite easy to confuse a drywall with a plaster but there are some differences. Not only is plaster a much older style of wall construction than dry wall, but it’s also a lot more expensive than installing a drywall. Plaster walls are also able to provide you with a more durable finish when compared to a drywall and it makes for a better quality finish.

Artexing a ceiling can be a tricky job, but whether you’re considering hiring a professional or DIY, it’s helpful to know how it’s done.

Artex is available either in a paste or powder form. The paste is ideal if you’re making small repairs or additions to an existing ceiling. But, if you have a whole ceiling to cover, the powder is more cost effective. When you’re ready to get started, you’ll need to mix the powder up with cold water according to the instructions.

It’s possible to artex over plaster, plasterboard or paint. If you have a plasterboard surface, you should tape and fill any joints or cracks before you begin. Plaster and plasterboard both require a coat of sealant or primer first. You can usually artex straight over paint, but any gloss paint should be sanded down, and any dark paints covered with a layer of white.

Artexing can get quite messy, so make sure you empty the room you’re working in as much as possible, lay down sheets and wear protective clothing and glasses. You might want to practice on a piece of board before you start on the ceiling.

Start by using a brush or roller to cover a 500 square cm area with a generous layer of artex. Then use a brush, comb or roller to create your chosen texture. Every time you do a new section of ceiling, try to blend it with the other sections you’ve done. Don’t be tempted to cover the whole ceiling before you start adding texture – the artex will dry too quickly for you to do it all in time.

Artex usually needs 12-24 hours in a well-ventilated space to dry completely.

It’s possible to paint your artex ceiling if you want to smarten it up or make it a different colour.

If it’s never been painted before, you’ll need to paint it with a PVA-based solution or water-thinned paint layer to start with. You may want to scrape or sand off any loose or peeling patches beforehand, but only do this if you’re sure that the artex doesn’t contain any asbestos.

Once you’ve done this, follow with two coats of your paint of choice – ideally an emulsion. If your artex ceiling has been painted before then you can paint directly without priming. However, if you’re painting over a particularly bold colour with a lighter one, you might want apply a layer of white paint first.

Artex is a water based decorative surface coating is typically incorporated on both walls and ceilings so as to apply a pattern. During the peak of its popularity in the 1970’s, it was considered the height of fashion when it comes to interior wall designs however its major drawback remains the fact that it usually contains asbestos especially if it was manufactured before the laws governing the use of asbestos was changed in the year 2000. And asbestos, as we know it, can be deadly when disturbed and its fibres are inhaled.

If you have artex installed in your purchased property and you do not know when the artex walls were done, or perhaps you just want to change the aesthetic design of your home into something more modern and to your personal taste, then you may want to remove the existing artex from your property for good. If this is your wish then you’ve come to the right place.

To remove artex from your walls you can choose to do so using the steaming method or through the use of an external product.

Using the steaming method, you should know that it’ll be more labour intensive and time consuming. You need a lot of patience moving your steamer slow and steady because if left on a spot for too long can damage the wall behind the coating. Once the artex has been dampened with the steamer, you can then scrape them off with a handheld scraper.

A faster solution would be to use an external product to remove your artex.  For example, you can use X-Tex which is a water-based coating remover. All you need to do is paint the substance over your artex wall and leave to dry for about 30 to 60 minutes before peeling away the artex.

How Much Does Plastering Cost?

If your existing interior or exterior plaster is starting to show signs of needing to be refreshed or the painting never seems to last, then it’s probably time to have your plaster renewed to breathe in a new lease of life to your decorating efforts.

So if you’re giving wall plastering a thought, there’s a need to have a rough estimate of the cost a professional is likely to charge so you can set a budget and start planning. However a direct answer can not be provided for this question as there are so many factors that a professional will put into considering before coming up with a quote that’s unique to your specific requirements.

A lot of plasterers will come up with a quote for the job using the number of square metres of wall space that’s going to be covered. This is due to the number of plasterboards as well as the other materials that the plasterer will need to purchase, how long the work will take and also the labour that’ll be involved in completing the project.

Another popular influencing factor that several plasterers use is the size of the room to be plastered. This is the main reason why you’re more likely to find the prices in small, medium as well as large rooms. Therefore, in order to have a more accurate estimate of the cost of your plastering project, you’d have to call in a qualified professional to have a look at the job at hand. Generally, to re-plaster a small room will cost within the range of £350 to £550, a medium room will cost within the range of £400 to £600 and a large room, between £550 to £700.

Plasterboard or drywall is simply gypsum plaster covered from both sides by thick paper layers. It’s known to be a highly versatile product used on both interior walls and ceiling as a result of its numerous advantages. This popular material in residential buildings can be designed to be fire resistant, humidity resistant and noise resistant. They have a low impact on the environment, while also being quite easy to repair and perfect to hide stuffs from plain sight. Most home and property owners in the UK have this material installed in their space as despite the multiple benefits, they’re also quite affordable. However, if you’re thinking about installing a plasterboard on your ceiling, one challenge you’re likely to face is determining the appropriate plasterboard thickness to incorporate as this make or mar your entire project. In this post, we’re going to take a look at the right plasterboard thickness for ceiling so as to help you make an informed decision moving forward. Let’s take a look!

Firstly, let’s consider the size of the plasterboard sheet. The standard plasterboard sheet size is 120 cm in width and within the range of 180 cm to 360 cm in height. These sizes are designed to provide the much-needed support to the standard stud spacing which is 160 cm. Depending on the manufacturer, plasterboard can be in four different widths. Now talking about the thickness, there are two standard thicknesses of plasterboard - 9.5 mm and 12.5 mm. The sizes of plasterboard for ceilings are 9.5 mm or 10 mm. Most individuals tend to assume that the thicker the plasterboard the better, but this is absolutely false. A thicker plasterboard will only stick harder to the ceiling which will make it hard to seal joints if required.