Find a Plasterer you can trust in Rhosgoch.

If your artex ceiling is looking tired or you just fancy a change, you can try plastering over your artex. You have two options when it comes to plastering over your artex: plasterboard or skimming.

Covering your ceiling with plasterboard is a good option if you suspect the artex may contain asbestos. If done carefully, it doesn’t involve disturbing the artex, reducing the risk of asbestos exposure.

You also have the option to skim over your ceiling. The first steps to this involve removing loose and flaking parts, cutting off stipples and sanding your ceiling down. So, if there’s a chance your artex ceiling may contain asbestos, this isn’t the right solution for you. However, if you’re sure there’s no asbestos in your ceiling, then sanding down and skimming over your ceiling can be a great way to create an attractive result.

It’s worth noting that both putting up plasterboard and skimming plaster can be difficult jobs. Although possible to DIY, you’re likely to get much better results if you hire a professional.

Also referred to as drywall, plasterboard is a panel that features an inner layer of gypsum and spread between facer as well as backer paper. It is mostly incorporated in the construction of both interior walls and ceilings. Plasterboard can be made to be humidity resistant, fire resistant as well as noise resistant. Due to these reasons and also the fact that it’s very easy to install and very affordable, plasterboard is a very popular choice when it comes to interior walls and ceilings.

One of the major issues that most homeowners face when fitting plasterboard is the thickness required to make the project a long lasting one. But not to worry, we got you covered! If you’re about to install plasterboard for your ceiling and wondering the thickness that’ll be appropriate, then you’ve come to the right place. In general, the standard plasterboard sheet size is 120 cm in width and within the range of 180 cm to 360 cm in height. These sizes are designed to provide the much needed support to the standard stud spacing which is 160 cm. Depending on the manufacturer, plasterboard can be in four different widths.

Now talking about the thickness, there are two standard thicknesses of plasterboard - 9.5 mm and 12.5 mm. The sizes of plasterboard for ceilings are 9.5 mm or 10 mm. Most individuals tend to assume that the thicker the plasterboard the better, but this is absolutely false. A thicker plasterboard will only stick harder to the ceiling which will make it hard to seal joints if required.

Plasterboards are a great noise insulators which can also reduce disturbances from other activities. As a result, for walls, size of plasterboards that’s considered appropriate for walls is 12.5 mm or 13 mm.

Artexing a ceiling can be a tricky job, but whether you’re considering hiring a professional or DIY, it’s helpful to know how it’s done.

Artex is available either in a paste or powder form. The paste is ideal if you’re making small repairs or additions to an existing ceiling. But, if you have a whole ceiling to cover, the powder is more cost effective. When you’re ready to get started, you’ll need to mix the powder up with cold water according to the instructions.

It’s possible to artex over plaster, plasterboard or paint. If you have a plasterboard surface, you should tape and fill any joints or cracks before you begin. Plaster and plasterboard both require a coat of sealant or primer first. You can usually artex straight over paint, but any gloss paint should be sanded down, and any dark paints covered with a layer of white.

Artexing can get quite messy, so make sure you empty the room you’re working in as much as possible, lay down sheets and wear protective clothing and glasses. You might want to practice on a piece of board before you start on the ceiling.

Start by using a brush or roller to cover a 500 square cm area with a generous layer of artex. Then use a brush, comb or roller to create your chosen texture. Every time you do a new section of ceiling, try to blend it with the other sections you’ve done. Don’t be tempted to cover the whole ceiling before you start adding texture – the artex will dry too quickly for you to do it all in time.

Artex usually needs 12-24 hours in a well-ventilated space to dry completely.

Artex is a water based decorative surface coating is typically incorporated on both walls and ceilings so as to apply a pattern. During the peak of its popularity in the 1970’s, it was considered the height of fashion when it comes to interior wall designs however its major drawback remains the fact that it usually contains asbestos especially if it was manufactured before the laws governing the use of asbestos was changed in the year 2000. And asbestos, as we know it, can be deadly when disturbed and its fibres are inhaled.

If you have artex installed in your purchased property and you do not know when the artex walls were done, or perhaps you just want to change the aesthetic design of your home into something more modern and to your personal taste, then you may want to remove the existing artex from your property for good. If this is your wish then you’ve come to the right place.

To remove artex from your walls you can choose to do so using the steaming method or through the use of an external product.

Using the steaming method, you should know that it’ll be more labour intensive and time consuming. You need a lot of patience moving your steamer slow and steady because if left on a spot for too long can damage the wall behind the coating. Once the artex has been dampened with the steamer, you can then scrape them off with a handheld scraper.

A faster solution would be to use an external product to remove your artex.  For example, you can use X-Tex which is a water-based coating remover. All you need to do is paint the substance over your artex wall and leave to dry for about 30 to 60 minutes before peeling away the artex.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

✓ Firstly, you need to put the plasterboard sheet flat on a firm surface.

✓ Use the tape measurement to measure the cut you wish to make.

✓ With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

✓ Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

✓ Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

✓ The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

✓ Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

✓ Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

✓ Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Although they’re pretty much outdated now, artex happens to be a very popular surface coating option just a few decades ago. Several homeowners with artex in recent times would either want to have them removed or cover them up with stuffs such as a wallpaper. So if you’re wondering whether or not it’s possible to wallpaper over artex, then there you have it. It’s possible to wallpaper over artex, however it’s not advisable as wallpaper may eventually crack over time. On the other hand, the artex can also create ridges beneath the wallpaper which allows unpleasant protrusions in the wallpaper. Instead of applying wallpaper over artex, a more permanent solution would be to cover it with drywall or wet plaster or perhaps just have it removed completely.

There are two types of wallpaper, there’s the thin wallpaper application which comes with adhesive on one side as well as a pattern or colour on the other side. With this, all you need do is simply to peel and stick. Then the other type is the sturdier wallpaper that’s more thick and requires a special wallpaper paste. However, it’s important to note that if you choose to wallpaper over your artex, you won’t be able to make use of the thin type of wallpaper, rather you’ll have to incorporate the sturdier  option which makes use of wallpaper paste.

The wallpaper paste is the product you mix with water to produce a paste which you’ll have to apply to your walls before applying the applying the regular wallpaper - one without adhesive on one side. Appling wallpaper to an artex decoration may just give you the updated appearance you so much desire.

Installing a plasterboard on your ceiling is a cool way to modernize your property. Over the past couple of decades, there has bee an increasing number of trends associated with plastering of both walls and ceilings such as rounded edges and textured plaster. However, in recent times, home and property owners are now looking to install more of sharp edges. If you’re planning to plaster your ceiling, you’d probably want to know just how much this project is going to cost. If yes, then you’ve come to the right place. In this article, we’ll give you a rough estimate of ceiling plastering costs.

There are a plethora of factors the can influence the price of plastering your ceiling. These pricing components includes the following:

✓ Size. As you would have expected, the larger the job, the more the overall cost. However, the price per square metre will reduce which means that the cost of plastering a small ceiling space will cost more per square metre than the cost of plastering a larger ceiling space per square metre.

✓ Materials. We have a wide range of plasterboard available in the market. If you need a fire retardant, acoustic or other types of specialist plasterboard, you can expect to pay higher than standard plasterboards.

✓ Location. Just like many other home improvement projects, the cost of plastering ceiling varies greatly throughout the UK. Places such as London and the South East have the highest prices due to the high standard of living as well as greater demands.

In general, to plaster a ceiling (small 2 m x 2 m) - overboard and plaster will cost within the range of £200 to about £300. Also, to plaster a ceiling (large 5 m x 6 m) - overboard and plaster will cost within the range of £400 to about £600. The average plasterer’s daily rate (including material) is about £180 to £300 and ceiling plastering cost per square metre ranges between £20 to £40.

Artex is a water based surface coating which is used to decorate both ceilings and walls with a textured finish. Back in the 1970’s, artex happens to be very popular when the swirling or spiky effects it creates  were considered to be the best of fashion when it comes to interior designs. However, in today’s world, an artex ceiling is not only considered outdated but also a pain to clean and repair.

If you have an artex ceiling in your residential property and looking for a way to get it off, then you’ve come to the right place. In this post, we’re going to show you how its done without much stress.

To get started you’d need to get the following tools and material which includes: safety goggles, dust mask and rubber gloves, plastic sheeting, canvas drop cloth ( carpet) or rosin paper (hard floor) and step ladder

Prepare the room. Start this by moving all furniture out of the room or stack the furniture at the centre of the room and cover using plastic sheets. Once done, cover all non-removable items with plastic sheets and lay down a canvas drop cloth for carpet floors and rosin paper for hard floors

• Put on your safety gear
• Use a utility knife or joint knife to slowly chip away at the texture and create a smooth surface.
• Mix joint compound in a bucket as per the instructions on the package
• Skim the surface with a thin layer of joint compound to smooth it out using a taping knife, then leave to dry overnight before you proceed
• Lightly sand the surface smooth with the help of a 220-grit sanding block
• Use a damp cloth to wipe the surface clean prior to painting.