Find a Roofer you can trust in Milltimber.

One of the most popular choices for roofing materials are roof slates. There is a number of advantages that a roof slate has, hey can be aesthetically pleasing, they can also increase the potential selling value of the house and many more. Slate is a sturdy and resilient material that delivers waterproofing physical characteristics to a pitched roof. Unlike other roof materials which absorb water slates do not. Therefore, slate is the most resistant towards freezing and water damage.

Find out the pitch of your roof

Before beginning with the fitting procedure, you need to figure out the pitch of your roof. The roof pitch commands how much overlap is essential with each slate. This has been made a lot easier than the early days with the advancement of technology.

Find out the required overlap

Once you’ve found out the exact pitch of your roof accurately, take a look at the slate producer’s description. Each manufacturer will propose the obligatory overlap in order to form a firm and safe slate roof.

Roll out the roof membrane

Firstly, guarantee your joists or trusses are clean of any sheards or old nails that could harm the membrane. You will now have to roll the chosen roofing membrane along the roof trusses. It is always wise to start from one of the bottom corners and keep rolling it along to the other corner.

Secure the roof membrane

Once the membrane has been moved out, use thump nails to protect one edge. You will now have to pull the membrane taut and carefully fix it into position. Do this before adding any nails across the membrane at points of intersection with the trusses for extra stability.

Batten placement

This is done to find the proper assignment of the battens. For this, you will need two full-sized slates along with an under eaves slate. Carefully position the battens on the top of the roof on the top of the overlay. Make sure not to fix them down since it will be easier to move them around and make any adjustments.

How To Clean Roof Tiles?

If you’re a DIY person with a dirty roof tiles or just a homeowner who’s also a lover of knowledge, you may probably like to know how you can have your roof tiles cleaned. This is a very common question which often depends on the dirt or debris you’re dealing with as well as the type of roof you possess. Most often than not, if you own a traditional concrete or slate roof tiles, then you’re more likely to battle moss and or algae growth.

If you’re not a competent DIY person or do not have enough confidence to pull this off, then it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, you’ll learn how to go about cleaning your roof tiles. Let’s have a look!

✓ Consider Safety. When it comes to roof cleaning, you have to be very careful. They’re normally high up and any task that deals with height will usually require putting safety measures in place. Firstly, it’s important to be confident with heights and ladders, if not you’d have to find someone who is. And if you’re confident, there’s also the need to find someone who can help you hold the base of the ladder.

✓ Trim the trees. Nearby trees are usually a threat to any roof and also makes cleaning much harder. So it’s always wise to cut any overhanging branches before you proceed.

✓ Bleach or not to bleach. Although you have to be very careful using beach and water but it also happens to be one of the easiest DIY ways to clean your roof. You either stand about 4 feet away and rely on water pressure or clean down the tiles by hand.

✓ Try not to make use of a blaster.

Gutters are a crucial component of any roofing system. They’re designed in such a way to protect your home or property from serious water damage, but keeping them clean and in good condition is something that’s almost always forgotten or ignored. Do not be deceived even when rain water is still running from them or they don’t appear to be clogged. Failure to clean maintain your gutters can lead to a wide range of outcomes and they aren’t so pretty. According to experts, gutter cleaning should be done twice a year - once in the spring and once in the fall. In order to help you realize the importance of cleaning your gutters, we’ll look at some of the possible outcomes of a neglected gutter.

• Leaky roof. If your gutters get clogged and cannot move water away from your home, it begins to build up on the roof and eventually lead to damages like rot and mold. As the damages spread, the end result could be a severe damage to the attic and supports.
• Damaged foundation. If the gutters are not functioning as they should, water saturation becomes a great threat to the foundation of your home or property. The concrete will crack or wood rots and you can also end up with mold.
• Creepy crawler infestation. Wherever you have stagnant water, there are also bugs. This is because they love the wet and moisture-filled gutters. You get unwanted visitors like carpenter ants, roaches and mosquitoes, just to mention a few.
• Driveway and path damage. When the downspouts aren’t directing the water to the appropriate spot, the excess that comes in contact with these surfaces can lead to cracks or sagging.

A leaky flat roof is one of those things every home and property owner would rather prefer to avoid. Not only can it be extremely frustrating to deal with, but it can also have a grave impact on the overall integrity and value of your property especially when things are not done properly. Generally, all leaky roofs pose serious problems, however, a leak in a flat roof is even a lot more complicated. Ranging from the quite simple repairs to the incredibly complex fixes, flat roof repair (also known as low slope roof repair) is be seriously problematic and at times, can call for a reconstruction which involves complicated roof insurance as well as an experienced professional support.

Flat roof repair consists of many different types. Cap sheet roofs possess layers of material glued together with hot asphalt, including a roll of mineral surface glue using asphalt to the top rather than gravel. The tar and gravel roofs also possess layers of material glued together with the help of hot asphalt, with the use of asphalt on top as well as gravel included in the asphalt. A modified bitumen roof possesses more strength when compared to a cap sheet roof or the conventional tar and gravel roof. This can be 2 or 3 plies, smooth or with a mineral surface, torched on, mopped on or self adhering. What’s more? A TPO roof is a single ply roof which is usually heat welded together. A PVC roof is also a single ply roof that’s heat welded together while an EPDM is a single ply roof that’s glued together. The foam roofs as well as various coatings are incorporated to reflect the sun’s UV rays and also to maintain and seal the roof.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

How To Clean Roof Lights

If you have existing roof lights or perhaps you’re about to have them installed, it’s important to know just how to have them cleaned, even if you wouldn’t be doing it yourself. Generally, glass roof lights fitted in flat roof applications are more likely to be a major victim of staining and discolouration by several elements like rainwater, bird droppings, vehicle exhaust pollutants as well as tree sap. Therefore, just like any other parts of your home, periodic inspection of the units as well as regular cleaning is highly advised to help maintain their top performance for a lengthy period of time.

Firstly, when installing the roof lights, it’ll be helpful if its fitted at the right pitch so as to help keep the exterior clean as it enables the elements such as rainwater to run off the surface naturally. Cleaning roof lights involves working at height which can be very dangerous. Therefore, if you lack the skill and confidence to pull this off, it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, we aim to give you a good insight into how the roof light cleaning process works. Let’s have a look!

Rooflight Interior Cleaning

✓ Spread plastic under the roof light to catch dirt and spills

✓ Dust to wipe clear all loose dirt and cobwebs.

✓ Use a squeegee with a warm soapy water or any other glass cleaning product to clean the glass ( steer clear of any harsh chemicals or abrasive cleaners)

✓ Dry the roof light with a soft and lint-free cloth.

Rooflight Exterior Cleaning

✓ Access the roof safely with a specialist ladder

✓ Put mild detergent into a bucket and carry up to the roof before filling with warm water from a hosepipe

✓ Use the soapy water and a non-abrasive cloth or squeegee to clean the roof light, its surroundings as well as fixings.

Whether you’re liable for a leaking roof in a commercial property will depend on your ownership status and any contracts. Of course, if you own a standalone commercial property, it would make it your responsibility to repair to leaking roof. But if you own an office within a building, you should check your paperwork to see whether you are responsible for some or all of a leaking roof.

If you’re a tenant in a commercial property, things get a bit more complicated. Lots of commercial leases are FRI, or Full Repairing and Insuring leases, which means that the tenant is responsible for all external and internal maintenance and insuring the building. It means that it’s vital that you read through your tenancy agreement in full before signing it and seek legal advice if you think you need it. If your lease is an FRI lease, you are liable for a leaking roof in your commercial property.

It’s important to ensure that you have a schedule of condition for the property, which will mean that you only have to restore the commercial property back to the condition that it was in when you took over. It’s also worth getting the roof inspected before you sign the lease, as if there is any damage before you sign the landlord may be responsible.

The best way to avoid having to pay for a leaking roof in a commercial property is prevention. If you are liable for repairs and maintenance, make sure you have the roof inspected regularly by a reputable company to avoid having to pay for costly repairs when disaster strikes.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.