Find a Roofer you can trust in Slough.

Yes – you can repair a flat roof in the winter. Contractors will still be able to help you repair leaks, and it’s a myth that they will charge more. Most won’t have any additional costs just for coming out in the winter.

You'll have to wait for any snow and ice to melt before you can repair your flat roof. Depending on what type of flat roof you have, some repairs might have to wait until temperatures reach a certain level above freezing – some coating products won’t adhere (stick) in low temperatures, but a roofing professional will be able to advise you on what is best to use in the winter. If you have an EDPM rubber roof, most of the adhesives won’t mix in cold weather, so you might have to wait until temperatures rise to get a proper repair to your flat roof.

The best way to avoid needing to repair your flat roof in the winter is to inspect it at regular intervals. During the summer, even in the UK’s mild weather, the sun’s UV rays can damage and weaken flat roof surfaces, potentially causing cracks and holes. As autumn approaches, take a look at your flat roof and see if you notice anything untoward. If you do, speak to a reputable roofer who can repair your flat roof for you before winter arrives.

As long as you can access them safely, it’s fairly easy to clean soffits and fascias. Using a sponge and warm water to scrub them is a good way to get off most types of dirt. You might want to add detergent or bleach to the water to make it more effective.

Once you’ve scrubbed your soffits and fascias, rinse them with clean water to make sure you’ve got all of the dirt and detergent off.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Most Sun Tunnel Kits are available in sizes from 250mm Diameter to 550mm Diameter. This gives you a good range to choose from depending on the size of the room you are trying to brighten.

• 250mm Sun Tube – Perfect for room sizes up to 10m2. (Hallways, Small Bathrooms)
• 350 – 450mm Sun Tubes – Perfect for rooms 10 to 15m2. Larger Hallways, Stairwells and Bathrooms.
• 550mm Sun Tube – Ideal for rooms 15 – 22m2. Kitchens, Bedrooms, Living Rooms.

A leaky flat roof is one of those things every home and property owner would rather prefer to avoid. Not only can it be extremely frustrating to deal with, but it can also have a grave impact on the overall integrity and value of your property especially when things are not done properly. Generally, all leaky roofs pose serious problems, however, a leak in a flat roof is even a lot more complicated. Ranging from the quite simple repairs to the incredibly complex fixes, flat roof repair (also known as low slope roof repair) is be seriously problematic and at times, can call for a reconstruction which involves complicated roof insurance as well as an experienced professional support.

Flat roof repair consists of many different types. Cap sheet roofs possess layers of material glued together with hot asphalt, including a roll of mineral surface glue using asphalt to the top rather than gravel. The tar and gravel roofs also possess layers of material glued together with the help of hot asphalt, with the use of asphalt on top as well as gravel included in the asphalt. A modified bitumen roof possesses more strength when compared to a cap sheet roof or the conventional tar and gravel roof. This can be 2 or 3 plies, smooth or with a mineral surface, torched on, mopped on or self adhering. What’s more? A TPO roof is a single ply roof which is usually heat welded together. A PVC roof is also a single ply roof that’s heat welded together while an EPDM is a single ply roof that’s glued together. The foam roofs as well as various coatings are incorporated to reflect the sun’s UV rays and also to maintain and seal the roof.

Fibreglass, or GRP, flat roofs are very durable and should last you years, but over time they can become brittle and you might see some cracks or holes forming. Luckily, you can repair a fibreglass flat roof and it doesn’t have to be too difficult. Cracks in a fibreglass flat roof If you notice long cracks in your fibreglass roof, you can often use a fibreglass crack sealant. Simply clean the area, squeeze the sealant into the crack, then smooth it off. If you want it to look neater, you could coat the entire roof with a restorative coating which will make it look new again. Hole in a fibreglass roof If you notice a hole in your fibreglass flat roof, you’ll want to get this repaired as soon as possible to avoid any rainwater getting into your home. There are lots of fibreglass roof hole repair kits on the market, both online and in DIY stores, so you shouldn’t have trouble picking one up. They usually contain a mouldable UV cured patch that you can stick onto the hole. It will harden and become instantly weatherproof, so is the perfect emergency repair solution. Fixing pin holes in a fibreglass flat roof Unfortunately, if you find pin holes in a fibreglass flat roof it’s often because the installer didn’t use enough resin during the fibreglassing process. Luckily, if you can’t get back in touch with the installer or you only notice after a few years, you can fix this yourself. Sand down the roof back to the clear resin layer. Clean the entire roof with acetone and reapply some GRP roofing resin. Ensure that all the pinholes are filled – you might need two coats.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

Strong winds can cause extensive damage to unprotected rooftops and in fact tiles act as very suitable protection. The extra weight they provide is great at countering high wind loads and if anything is damaged during severe weather, replacing tiles is straight forward for professional roofers.When you compare this to lightweight materials there’s a significant difference. If you wish to have extra protection, experts recommended having sarking fitted.