Find a Roofer you can trust near you.

Chimneys are certainly on top of the commonly overlooked features when it comes to cleaning a house. This is quite understandable given the fact that they’re not readily accessible and not in plain sight, hence, home and property owners tend to overlook the relevance of any chimney cleaning effort. But this can be a grave mistake! The importance of having your chimney swept on a regular basis cannot be over emphasized and even more so if it happens to be on a wood burner. Not only can a dirty chimney constitute fire hazard, but when left uncleaned it can also give rise to blockages which can lead to carbon monoxide poisoning. In fact, from 2014 to 2018, one of the top factors contributing to about 25% of home heating fires is due to lack of cleaning, mainly from solid-fueled heating equipment, mostly chimneys. Therefore, sweeping your chimney regularly is a safety precaution and when they happen to be on a wood burner, this exercise becomes a lot more important. With that in mind, the question that arises is just how often is sweeping of a chimney on a would burner needed?

Well, it’s strongly advisable to sweep chimney on a wood burner at least twice a year by a qualified professional depending on the usage. If you happen to own an oil burning fireplace, the same also applies. In other words, this means that regardless of the type of chimney you possess, the cleaning must be done regularly. However, most chimney would only need to be swept once in a year by a qualified professional.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

How to repair your flat garage roof will depend on what it’s made from. Lots of flat garage roofs are made from EDPM rubber, asphalt or felt. We’ll explain how to carry out repairs on your garage roof here. EDPM rubber flat roof repair EDPM rubber is an excellent choice for a flat garage roof and should need little maintenance. But if you do need to repair it, there are a few easy fixes. If it’s a small crack or tear, apply some lap sealant to the area, but don’t use too much. If you go for a more professional repair later, the sealant will need to be scraped off, so if there’s too much it might cost you more in labour. If you need to repair the flashing, buy some malleable flashing tape so you can form it into the right shape. Clean and dry the area that needs repairing, then apply an EDPM primer. When that’s touch dry, stick the patch of flashing tape down from the centre outwards with a roller. Repairing an asphalt flat garage roof Asphalt is also very hard-wearing, and when it does need fixing, the fixes often last a long time. So if you do get cracks or blisters, you can use a paint-on fix from a tin as a temporary repair. When it’s time for a more permanent fix, you can add a small patch of torched-on roofing felt or use a liquid system, but the high-quality ones are often only available to trade customers. How to repair a felt flat garage roof Felt can be repaired in a similar way to asphalt flat garage roofs. For small cracks or a temporary fix, try a paint-on treatment from a tin. But for something more permanent, use a patch of torched-on roofing felt or a liquid system. If these don’t stick, unfortunately it means it’s time for a new felt garage roof. If you do need a new flat garage roof, leave it to the professionals who will ensure that your new roof will last for years.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

Whether you’re liable for a leaking roof in a commercial property will depend on your ownership status and any contracts. Of course, if you own a standalone commercial property, it would make it your responsibility to repair to leaking roof. But if you own an office within a building, you should check your paperwork to see whether you are responsible for some or all of a leaking roof.

If you’re a tenant in a commercial property, things get a bit more complicated. Lots of commercial leases are FRI, or Full Repairing and Insuring leases, which means that the tenant is responsible for all external and internal maintenance and insuring the building. It means that it’s vital that you read through your tenancy agreement in full before signing it and seek legal advice if you think you need it. If your lease is an FRI lease, you are liable for a leaking roof in your commercial property.

It’s important to ensure that you have a schedule of condition for the property, which will mean that you only have to restore the commercial property back to the condition that it was in when you took over. It’s also worth getting the roof inspected before you sign the lease, as if there is any damage before you sign the landlord may be responsible.

The best way to avoid having to pay for a leaking roof in a commercial property is prevention. If you are liable for repairs and maintenance, make sure you have the roof inspected regularly by a reputable company to avoid having to pay for costly repairs when disaster strikes.

Commercial roofing simply refers to any roofing work, including installation and repair, that is done to commercial buildings. This might include office roofs, shop roofs or commercial unit roofs. Every building needs a roof to keep out the rain!

Since looks aren’t usually the first priority with commercial buildings, lots of commercial properties have flat roofs. These are often made from felt, EDPM rubber or fibreglass. Felt is the cheapest commercial roofing material, while fibreglass tends to be the most expensive. In felt roofs, roofers use an adhesive to stick roofing felt onto a frame. EDPM rubber roofs have a rubber membrane that is laid down and glued onto the roof and coated with a contact adhesive, while fibreglass uses a cut glass fibre mat that is pressed on before a resin and topcoat are applied.

Not all roofing companies will offer commercial roofing services, because generally the buildings tend to be bigger. Small companies won’t have enough tradespeople to work on a roof without making it very expensive for you. Commercial buildings also tend to need more scaffolding to make it safe for the professionals to work, so some smaller roofing companies won’t offer commercial services. Make sure you check a company’s website or social media if you’re looking for commercial roofing – on the Quotatis Directory, our roofers will show whether they do commercial roofing to make your search easier.

How To Replace A Broken Roof Tile?

If you have a broken roof tile on your property, the next logical step to take is having it replaced as soon as you can. However, this is not the simplest of tasks so you might need some guidance if you wish to do it yourself. If you lack the confidence needed to pull this off as it involves working at height, then we’d strongly recommend you hire the services of a reliable roofing contractor or company who can guarantee the best results for help. In this guide, we’re going to walk you through the processes involved in the replacement of broken tiles. Let’s have a look!

✓ Match your roof tiles perfectly. The most frequently used roof tiles are concrete and terracotta. They may look all similar but they can actually vary in shapes, length as well as thickness. To replace a broken tile, you must first make sure that it’s the same type of tile so it doesn’t interfere with the flow of your roof which can lead to further damage.

✓ Climb on to the roof. Make use of a strong and stable ladder to do this. If you’re not comfortable with heights, simply call in a professional. Falling of the roof would be more expensive.

✓ Remove the broken tile. Lift up the overlapping tile next to the broken tile in such a way to enable an easy removal of the broken one. If you’re not able to life them, then they probably have nails securing them in place. Remove these nails to proceed.

✓ Replace the broken tile with the new one. To do this, simply lift up the bottom tiles from the above row and then slide the new tile back in place. If the tiles have been nailed, make sure you also drive a nail through the hole in the new tile into the timber roof batten.