Find a Roofer you can trust in Newcastle Emlyn.

A leaky flat roof is one of those things every home and property owner would rather prefer to avoid. Not only can it be extremely frustrating to deal with, but it can also have a grave impact on the overall integrity and value of your property especially when things are not done properly. Generally, all leaky roofs pose serious problems, however, a leak in a flat roof is even a lot more complicated. Ranging from the quite simple repairs to the incredibly complex fixes, flat roof repair (also known as low slope roof repair) is be seriously problematic and at times, can call for a reconstruction which involves complicated roof insurance as well as an experienced professional support.

Flat roof repair consists of many different types. Cap sheet roofs possess layers of material glued together with hot asphalt, including a roll of mineral surface glue using asphalt to the top rather than gravel. The tar and gravel roofs also possess layers of material glued together with the help of hot asphalt, with the use of asphalt on top as well as gravel included in the asphalt. A modified bitumen roof possesses more strength when compared to a cap sheet roof or the conventional tar and gravel roof. This can be 2 or 3 plies, smooth or with a mineral surface, torched on, mopped on or self adhering. What’s more? A TPO roof is a single ply roof which is usually heat welded together. A PVC roof is also a single ply roof that’s heat welded together while an EPDM is a single ply roof that’s glued together. The foam roofs as well as various coatings are incorporated to reflect the sun’s UV rays and also to maintain and seal the roof.

How much a flat roof costs to repair depends on a few factors. Is your flat roof on a garage or an extension? What is the flat roof made from? It’s always best to get a few quotes to compare prices, but we’ll give you a rough idea here. If your flat roof was installed in the 1990s or earlier, it’s likely that you’ll see some leaks or damage soon. Felt flat roofs used to be installed completely flat, which meant that water couldn’t run off. That means that water pools and can create moss and damp. Sun exposure can also damage the felt, causing damage and eventually holes that lead to leaks. If you’re lucky enough to have got away with just needing a flat roof repair, this should set you back an average of £100 per square metre. If your roof is sagging due to the weight of it putting pressure on the timber frame, you might need additional joists – which could cost anywhere between £1,000 and £2,000, depending on how many you need. But if the problem is due to the internal part of the roof system becoming waterlogged, you could be looking at over £5,000. If your roof is severely leaking or the timber joists are rotting, it might be more cost effective to replace your flat roof. If you keep forking out for repairs, it will eventually be cheaper just to replace the whole thing, which could cost around £2,000.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

Will My Roof Leak With Missing Ridge Tiles?

Your roof is the first line of defence against the elements. Therefore, if you want your home protected at all times, there’s a need to ensure a professional inspection of your home at least once a year. However, there are certain issues that you do not have to wait for a professional to be able to spot by yourself. And an example of this includes a missing ridge tile. This issue is noticeable from the ground level while some tiles may even fall off and notifying you in the process. If you’re currently facing this kind of challenge, you’d probably want to know if the missing ridge tiles can cause your roof to leak. In this article, we aim to answer this question and more. Let’s take a look!

Firstly, there are a number of causes of missing tiles or slates and the most obvious is the weather. When the wind or rain gets very high, it can pull your tiles out of place and even more more, if they weren’t properly installed in the first place. Secondly, there’s also a chance that the nails may wear away. These are the nails that holds your ridge tiles in place, they can rust and wear away, hence leading to missing ridge tiles.

Therefore, the short answer to the question is yes, missing ridge tiles can cause your roof to leak. Even if it doesn’t leave a visible gap in your roof’s covering, it’ll create a break in the roof which weather can easily penetrate. And allowing this to happen makes the other tiles more susceptible to damage which won’t be good for the entire house as well as your pocket. Hence, once you notice a missing ridge tile ensure to have it replaced as soon as possible.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

Velux windows, or roof windows, are very easy to clean. Regular cleaning helps to keep them looking bright and shiny for years to come. So how should you clean Velux windows?

If you want to clean the air filter, you can remove it and wash it with your normal household cleaners. Velux windows have a cleaning position, so rotate and secure it into this position then remove the filter. You should be able to buy new filters from the manufacturer of your roof window.

To clean the outer pane, there’s no need to lean out of the window and risk falling out. Simply rotate the sash (the opening part) 180 degrees and secure it into position. Then you can clean the pane with a soft, lint-free cloth, sponge or squeegee and clean water. If you live in a hard water area, add some detergent to the water and wipe the window dry when you’re finished. You can also use normal non-abrasive household cleaners.

It’s recommended that you clean the flashing around your roof window at least once a year. You can use a brush to do this. This will allow rainwater to flow freely and stop any leaves from collecting.

If you’re in any doubt about using certain cleaners on your Velux windows, get in touch with the manufacturer who should be able to help. You can also do a patch test on an inconspicuous area if you’re unsure.

In the UK, fireplaces are a very common addition to homes and property and reasonably so. Not only do they represent a great source of heat, but they’re also quite timeless in their beauty, thereby adding more value to your property. Now every fireplace possesses some sort of chimney, asides from the ones that are ventless. And while you might not be aware, every chimney poses a number of dangers which includes being a fire hazard and can also lead to carbon monoxide poisoning as a result of improper or lack maintenance.

Since your chimney will be clogged up over time with all sorts of soot and often cleaned from the top of the roof, cleaning of a chimney comes with a huge amount of risk. As a result, you run the risk of falling off if you decide to clean one by yourself. And even if you’re the type that’s comfortable being on high level places, you should know cleaning a chimney is not the most pleasant of jobs. It can be quite messy as accumulated creosote and soot can drop into your home causing a cloud which covers both the floor, furniture and any other thing you have in the room. Furthermore, chimney cleaning requires specialized skills and knowledge which professionals have acquired after several practices. For instance, missing out on a spot can result in an unchecked chimney fire or a masonry crack.

The simple answer to this question is, therefore, a big NO - you should leave the cleaning to the professionals.  Professionals are not just limited to chimney cleaning; they’re trained to identify any structural issues while also being able to carry out a close analysis of the chimney. They’ll fix minor issues on site and give you a peace mind for any future wood burning activities.