Find a Roofer you can trust in Garndolbenmaen.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

The roof is a particularly important part of the home, providing weather and water protection. Therefore, it’s important to regularly check your guttering system and clean out any debris that could cause blockages.Advice given is to consider having a mesh gutter guard to prevent the build-up of leaves and other debris, especially if you want to harvest rainwater.

Chimney liners are a very important component of the chimney, but the fact is most home and property owners either continue to overlook them or aren’t even aware of their existence. This is, however, quite understandable given the fact that they usually last a long period of time – more than 50 years. To ensure that they last that long, the question that arises is, do chimney liners need to be swept and cleaned? The short and simple answer to this question is yes, chimney liners definitely needs to be cleaned on a frequent basis. A chimney liner happens to be an essential part of your chimney. When it’s not cleaned, it tends to accumulate dust, soot and dirt which can give rise to a number of problems you’d rather want to avoid. Chimney liner are able to provide adequate protection to your flue but even at that the water, creosote and other contaminant build up can make the liner to deteriorate, and making it unsafe for usage. In other words, contrary to several belief, chimney liners do need the same amount of cleaning as chimneys without liners. Failure to sweep your chimney liners can give rise to the following problems:

• Creosote buildup. If your main source of fire is wood, then you’ll definitely have creosote present in your chimney. This is highly combustible and its buildup may lead to fire outbreak.
• Carbon monoxide poisoning. Carbon monoxide is said to be on the rise by NCBI and its primarily generated from heating systems which are terribly ventilated as a result of uncleaned or dirty chimneys.

A roof is one of the most significant portions of any property and they’re also the single part of a structure most vulnerable to impairment from the elements. If your roof suffers substantial damage over time, maintenances and re-roofing charges can be expensive, time-consuming, and stressful which is why it is imperative to keep your roof in sound structural and aesthetic order.

If a tile has fallen off from the top of your roof – you can expect to pay around £70-£100 to replace it including a different tile fitted in its place. Replacing a hip roof will cost between £4,250 and £7,250, the cost varies if you have a single valley or a double valley on your roof. For a new gable roof, you should expect to pay around £3,250 to £5,250.

What does it cost to replace my roof?

The charge of substituting your roof for a new one will be subject to the age and condition that it’s in, but usually, the cost of a new roof on an average property is around £5,500.

Some of the key factors to keep in mind when calculating the cost of re-roofing your house include:

• size of your roof

• type and size of the materials used

• shape and style of the roof

• If structural changes are required or not

• the roofing company hired

Tiled roof repair costs

If you are trying to prevent water from leaking inside your house for one or two tiles, then you can expect to pay between £100 to £200 to fix them and seal the leaks.

Flat roof repair costs

Minor jobs such as repairing flat roofs as well as sheds and garages or mending blisters can usually cost around £300.

Roofing job Price range

Replacing six ridge tiles £135-£260

Replacing six broken or missing tiles £55-£105

Cleanout of your gutter £35-£80

Replacing one right tile on rooftop £70-£100

The cost of a full re-roofing job can amount to around £3,250 to £7,250 depending on the size of your property.

Hip roof Cost range Length of time

Semi-detached home £4,250-£4,750 3-4 days

Detached home £5,250-£5,750 4-5 days

2 valleys – semi-detached home £5,750-£6,250 5-6 days

2-valleys detached home £6,750-£7,250 6-7 days

Gable roof Cost range Length of time

Standard £3,250-£3,750 2-3 days

2-valley £4,750-£5,250 4-5 days

A pitched roof is a type of roof that is defined to have a sloping surface that has an angle that is greater than 20 degrees. Pitched roofs offer a more classical appearance. They remain the most communal and effective answer in wet and cold weathers to guarantee all-out protection.

Eaves

In the roof, the lower part of the inclined roof which is prominent outside the external face of the wall. The chief purpose of eaves is to pour the rainwater from the roof straight on the exterior wall. It also provides protection from sunlight. Eaves are sometimes decorated to an architectural beauty.

Gable

The Three-sided higher part of the wall at the end of a ridge roof.

Flashing

A band of impermeable material, typically metal, used to eliminate water from the intersection between a roof covering and another part of the structure. Flashings are provided to stop moisture from inflowing the wall and roof through joints in copings, parapet wall, and other infiltrations through the roof plane.

Hip

The Hip is defined as the exterior angle, which is generally greater than 180 degrees, which is formed at the inclined ridge of the roof slopes.

Ridge

The ridge is defined as the horizontal intersection made by the rising roof surfaces that are inclined in opposite directions.

Purlins

Purlins are the horizontal members which are laid on the principal rafters which help to support the common rafter of a roof. This is usually done when the span is large. Purlins are made from wood or steel. The top surfaces of the purlins intend to be unvarying and plane.

Fascia

This is the wooden board that is fixed to the feet of the common rafter at eaves. The Fascia helps the lowest ends of the roof covering material to rest on it.

Rafter

One of the major structural components of a pitched roof is a rafter. The rafter generally begins for the support of the roof to the ridge or hip. The purlin is supported by equally spaced rafters used side by side.

How long it takes to fix a roofing sheet on a commercial property will depend on the size of your roof and how difficult access is. Corrugated iron roofing sheets are much easier to fit than other roofing materials such as clay tiles or EDPM rubber, so that will work in your favour.

The size of the team of the roofing company you engage will also make a difference. If they have a lot of tradespeople working on your roof with lots of experience, it will take less time, while if there are only a couple of people it will take longer.

Another thing to bear in mind when considering how long it will take to fix a roofing sheet is the weather. If it starts to rain, the contractors will probably have to stop and wait, as the roof will be too slippery to work on.

In general, it should take between 1 and 3 days to fit roofing sheets on a commercial property. If you’re not having a full roof replacement, it may only take one day, whereas a completely new metal roof could take up to 3 days.

An eave is the edge of a roof, which is why they are now and then called roof eaves. On a household's outside, eaves can stick out outside the side of the building, serving both ornamental and applied purposes. The eave of a house has come to mean the lower area of the roof that projects after the external covering, as opposite to a cornice, which is part of the entablature in Classical architecture.

Think of how a roof outspreads outside the covering, and then think about how a hard rain may roll down the roof and, on the ground, away from the structure. Centuries ago, the eavesdrop was that indentation line made around a structure when the rain fell off the edge of the roof onto the ground.

Types of Eaves

A roof can come to a conclusion in essentially three ways. A closed eave is the one which has very little or no overhang at all. An open eave has a visible overhang, projecting beyond the roof brackets. A boxed eave is surrounded with a soffit.

The Use of Eaves?

An eave can defend the siding and substance of a structure. A roof eave bulging beyond the sides permits snow and rain to fall from the roof away from the covering, to the ground. The more the "weather" gets thrown away from the household, the chances of you having a dry basement increases.

In cases of regions with a warmer climate, a large eave can help provide shade to the interior of the house. In rainy environments, the prolonged eaves of Asian architecture deliver shelter from the climate, as well as direction. In the 21st century, an eave may be an inconspicuous site for security cameras and light.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.