Find a Roofer you can trust in Bargoed.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

A pitched roof is a type of roof that is defined to have a sloping surface that has an angle that is greater than 20 degrees. Pitched roofs offer a more classical appearance. They remain the most communal and effective answer in wet and cold weathers to guarantee all-out protection.

Eaves

In the roof, the lower part of the inclined roof which is prominent outside the external face of the wall. The chief purpose of eaves is to pour the rainwater from the roof straight on the exterior wall. It also provides protection from sunlight. Eaves are sometimes decorated to an architectural beauty.

Gable

The Three-sided higher part of the wall at the end of a ridge roof.

Flashing

A band of impermeable material, typically metal, used to eliminate water from the intersection between a roof covering and another part of the structure. Flashings are provided to stop moisture from inflowing the wall and roof through joints in copings, parapet wall, and other infiltrations through the roof plane.

Hip

The Hip is defined as the exterior angle, which is generally greater than 180 degrees, which is formed at the inclined ridge of the roof slopes.

Ridge

The ridge is defined as the horizontal intersection made by the rising roof surfaces that are inclined in opposite directions.

Purlins

Purlins are the horizontal members which are laid on the principal rafters which help to support the common rafter of a roof. This is usually done when the span is large. Purlins are made from wood or steel. The top surfaces of the purlins intend to be unvarying and plane.

Fascia

This is the wooden board that is fixed to the feet of the common rafter at eaves. The Fascia helps the lowest ends of the roof covering material to rest on it.

Rafter

One of the major structural components of a pitched roof is a rafter. The rafter generally begins for the support of the roof to the ridge or hip. The purlin is supported by equally spaced rafters used side by side.

Will My Roof Leak With Missing Ridge Tiles?

Your roof is the first line of defence against the elements. Therefore, if you want your home protected at all times, there’s a need to ensure a professional inspection of your home at least once a year. However, there are certain issues that you do not have to wait for a professional to be able to spot by yourself. And an example of this includes a missing ridge tile. This issue is noticeable from the ground level while some tiles may even fall off and notifying you in the process. If you’re currently facing this kind of challenge, you’d probably want to know if the missing ridge tiles can cause your roof to leak. In this article, we aim to answer this question and more. Let’s take a look!

Firstly, there are a number of causes of missing tiles or slates and the most obvious is the weather. When the wind or rain gets very high, it can pull your tiles out of place and even more more, if they weren’t properly installed in the first place. Secondly, there’s also a chance that the nails may wear away. These are the nails that holds your ridge tiles in place, they can rust and wear away, hence leading to missing ridge tiles.

Therefore, the short answer to the question is yes, missing ridge tiles can cause your roof to leak. Even if it doesn’t leave a visible gap in your roof’s covering, it’ll create a break in the roof which weather can easily penetrate. And allowing this to happen makes the other tiles more susceptible to damage which won’t be good for the entire house as well as your pocket. Hence, once you notice a missing ridge tile ensure to have it replaced as soon as possible.

You should inspect your roof twice a year, ideally after rain or snow, to see if it’s draining properly. Also in the Spring to check for damage that may of been caused over the winter months that will need to be put right before the next winter. Have an inspection carried out if you are unsure.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.

How To Replace Roof Tiles

If your roof tiles is cracked, missing or damaged in one form or the other, you may want to read up to see if the replacement is something you can do by yourself. The answer is yes, roof tiles replacement can be done as a DIY project especially if you’re an experienced DIYer or confident enough to tackle the project. However, if you lack the confidence needed to take on this task, then we’d strongly recommend you get in touch with a professional roofer who can guarantee the best results for help. In this article, we’ll show you how you can replace your roof tiles with relative ease. Let’s take a look!

✓ As you would have rightly guessed, the first step to replacing your roof tiles is to remove the existing damaged roof tile to create space for the new tile. In the event whereby the roof tile is nailed to down, you will have to pry the nails off before proceeding with the broken tile removal.

✓ Once the damaged tile has been removed, the next step is to replace the roof tile as there’ll now be a gap in the roofing area. Simply position the new tile rightly into the space that was formerly filled by the old damaged tile.

✓ After successfully placing the new tiles in spot of the removed tile, you’ll now have to replace the overlapping tiles to their correct position to secure them. To this with a hammer to lift the overlapping tiles a little bit, so you can pull them back into the appropriate place.

✓ This final step is not a necessary one. However, if you’d like to secure your roof tiles further, you can simply nail it into place with a hammer.