Find a Shop Fitter you can trust in Buckie.

If you happen to live in a quiet, serene environment ( or just cherish being in one) and wish to have an air source heat pump installed on your property, then you’d probably want to know just how noisy these renewable energy source are. In this post, we aim to provide answers to this question and more. Let’s take a look!

There is no short and direct answer to this question as air source heat pumps are available in varying shapes and sizes which makes the sound as well as volume of their noise different between models and manufacturers. However, as a result of government regulations, most of the contemporary air source heat pumps are able to function a lot quieter when compared to the older models. As you would have expected, modern air source heat pumps shouldn’t produce more than a low whirring sound provided they’re functioning as they should with no faults. On the other hand, the volume of the sound generated is largely dependent on the amount of work the air source heat pump is doing. This implies that a greater work load will generate a louder noise. This is due to the fan’s speed which works to absorb warm air into the compressor.

In order not to disturb the neighbours, noise pollution is normally determined at the design stage of the air source heat pump installation. The unit to be placed outdoor will typically be positioned as far from the neighbours property as possible and it’s also a great idea not to put the box directly under any windows. Overall, it’s always advisable to go for the newer models which tend to be better designed with thicker chassis and quieter fans.

Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.

Are you planning to remove or renovate your garage? Before proceeding with the intended project, it’s usually essential to firstly determine whether or not your garage contains asbestos. However, asbestos isn’t the easiest material to identify and even more so when you’re unsure of what it looks. The fibres on the other hand are not visible to the eye and can’t be smelt as it’s odourless. In this article, we’ll provide you some helpful tips to spot an asbestos garage roof. Let’s take a closer look!

✓ Figure out when the building was constructed. In the year 1999, a ban was placed on the use of asbestos in the UK, both to manufacture and supply of asbestos materials. As a result, if your garage was built before this period, then it’s very likely that an asbestos containing material was used. It’s also important to note that several garage roofs that contain asbestos are constructed with the help of flat or corrugated sheets of cement.

✓ Check the surface. When cement contains asbestos its usually fairly thin with visible fibres running through it. Also, the surface of the cement will have a texture and also some craters. If you an older cement sheets is incorporated, there’s a high chance that it contains asbestos.

✓ How it’s built. Asbestos materials are usually joined together by aluminium runners and help in position with nails that are blunt-ended. Take a look at the joints, if the sheets inside is held together by wooden or plastic runners then there’s danger.

Finally, roofs made from asbestos cement has a good chance of becoming very brittle.

What Is The Smallest Opening For Bifold Doors?

Generally, bifold doors comes in a wide range of sizes and configurations. So if you’re looking to install them in your home, the opening size required will depend on multiple influencing factors. However, the question we’re going to look at here is the smallest opening for bifold doors.

First and foremost, let’s consider the size of bifold doors as learning about how big or small bifold doors can play a key role in helping you determine the size of bifold door you’ll need. Generally, the size of bifold doors will vary largely depending on the manufacturer, but they are usually within the range of 6.8 feet and 7 feet in height. The width, however, will be determined by the number of door panels you’d like to use but several configurations are designed in such a way that they can be installed in openings of about 1.8m and above. For each door panel, the size are usually between 500 and 1000mm in width. As a result, if you decide to opt for door panels with a width of 700mm, you’ll need to get about 3 of the door panels in order to install in an aperture that’s wider than 1.8m. What’s more? Door panels can also be custom made especially if the size you need isn’t available.

So with that in mind, what’s the smallest opening for bifold doors? The bifold door’s minimum width is 1400mm. And in order to install a bifold door to fill this size, you’ll require two individual door panels that’s 700mm in width. Building them any smaller than the minimum width will be unwise as this will make them bind when closing.

Have you been advised by a structural engineer or a surveyor that your building needs to be underpinned? Well, this might just have you wondering what underpinning really is and how long it lasts. In this post, we’re going to tell you more about underpinning to help you make the best-informed decision possible moving forward. Let’s take a look!

Basically, underpinning refers to the incorporation of one of various methods to reinforce or repair the old foundations of a building or structure mostly to remedy or avoid subsidence. Now, subsidence can be caused as a result of poor soil quality, increase in the load on the foundation like adding a new storey, excavations below the building as well as inadequate foundation which is more common in older buildings. When an underpinning remedial work is carried out, there are a plethora of benefits that comes with it. It’s preserves the structural integrity of your building by strengthening it, make it a lot more attractive, increases the property’s value and makes it a lot safer for both you and your loved ones. So how long does underpinning last?

Well, many underpinning contractors will offer you a 10-year guarantee of its underpinning solutions for defects. Primarily, there are two reasons why underpinning can fail which is poor installation and fresh issues arising or unforeseen circumstances. While the first is an issue that can be avoided by employing the services of an expert contractor who possesses vast experience and knowledge in the field, the second can not be avoided. However, in the absence of the unforeseen issues, underpinning is expected to last for the natural life of the building, so far it has been expertly installed.

Not if you don’t want to! The size of many appliances is standardised, meaning they should fit in to any new kitchen. Ask an experienced kitchen designer or installer if you’re not sure if your current appliances will fit into a new kitchen, and of course, new cupboards and worktops can be fitted around your existing appliances if you are keep them!

How Long Does It Take To Service An Oil Boiler?

Are you about to service your oil boiler and wondering just how long it would take to completion? Well, you should first know that during an oil boiler service, there are a wide range of things that needs to be checked. As a result, the service can actually take some time and even more, depending on the present condition of your oil boiler.

During a boiler service, your qualified heating engineer will carry out the following tasks:

• Detach and clean both the burner and fan.

• Examine the combustion chamber rope seal.

• Wipe clean and descale baffles.

• Wipe clean and descale the main heat exchanger

• Detach, clean and replace turbulators

• Examine the combustion levels after cleaning.

He’ll also perform some tank and system checks which includes:

• Inspecting and cleaning condensate

• Testing the fire valve

• Cleaning or replacing the filter

• Cleaning the condense trap

• Conducting a thorough inspection of the tank and oil supply pipe to identify possible damages, deterioration as well as debris.

• Pressure testing the oil supply pipe at the point where it goes underground.

• Examining the system pressure.

With all the aforementioned activities and more, an oil boiler service may take relatively longer period of time when compared to it’s counterpart - gas boiler. This is mainly due to the fact that the boiler itself requires a thorough inspection as well as the oil tank where the fuel is being stored. You get your gas through the mains supply, however oil must firstly be stored inside the tank then filled up when it’s almost low. The oil tank will be inspected to identify possible leaks, bulging, corrosion as well as water.

So generally, an oil boiler service should take between the range of 1 to 2 hours to be completed.

How To Repair A Pothole In Gravel Driveways

When the integrity of your gravel driveway is impaired not only does it have a negative impact on the curb appeal of your property, but also makes your driveway a danger zone. If your driveway needs to be repaired, you’d simply have to grab the bull by the horn and get it done - the sooner, the better to avoid the problem getting worse and to have your beautiful gravel driveway back as soon as possible.

The major cause of potholes in driveways is usually water, when it gets trapped beneath the surface of the driveway. Therefore, you may also want to enhance the drainage in the area as part of your repair. The repair process is quite simple for confident do-it-yourselfers, but if otherwise, then calling in a reliable professional will save you some time and extra money that can result from possible errors. So how do you repair gravel driveway potholes?

✓ Prepare the area. This involves removing all forms of debris from the pothole. To achieve this, you can rake, shovel or brush the loose stones, soil and other debris from the pothole.

✓ Fill the pot hole. Make use of a coarse gravel to fill up the pothole to a depth of about 3 inches beneath the driveway’s level. Upon the filling, simply tamp down the coarse gravel using a commercial tamper or any available homemade option. Once done, the final 3 inches to the surface of the gravel driveway should then be filled up with gravel which perfectly matches the colour and texture of the remaining driveway.

✓ Compact the patch. To achieve this in an easy and fast way, simply run your car’s wheel up and down over the repaired spot gently a couple of times. This will be enough to compact the patch and seal the pothole.