Find a Shop Fitter you can trust in Duns.

It’s important to get the right size solar panel system for your commercial property. Solar panels are usually installed on pitched roofs, although they can be fitted on stands on the ground if you have some unused outdoor space. The more panels you install, the more power you’ll generate, but there’s no point buying more panels than you have space for.

Solar panel system sizes are measured in kW. 4-10kW solar panel systems are usually too big for domestic properties but are ideal for smaller commercial properties. Here’s an idea of how many panels and space you’ll need for a few different system sizes:

System size, Number of panels, Area required (approximate)

4kW, 16, 23m²

6kW, 24, 35m²

8kW, 32, 46m²

10kw, 40, 58m²

Bear in mind that solar panels can’t be less than 30cm away from a roof edge, so you’ll need more space than the area that the panels take up.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

The OLEV Grant, also known as Electric Vehicle Homecharge Scheme (EVHS) can reduce the cost of your home charger by up to £350. If you're eligible, you'll be able to claim it when you buy an EV charger.

Cookers usually look best if they’re installed at the same height as the work surfaces they’re next to. Most range cookers have adjustable legs so that they match a range of work surface heights.If you want your range cooker to match your work surface height, make sure that your installer knows this before they get started.

What Is Plasterboard?

The plasterboard is unarguably one of the most common building materials across the globe. Sometimes referred to as gypsum board, gyprock, drywall or wall board, the plasterboard is mostly incorporated for ceiling cladding and interior walls in several homes and offices in recent times. However, despite its global acceptability, it’s a very misunderstood building material.

The plasterboard is manufactured using a gypsum core with a heavy paper covering both sides of the sheet. The measurement of a standard plasterboard sheet is a length of 2.4 metres in and a width of 1.2 metres, with a thickness of about 13mm. The board usually have either a bevelled or a bit flat edge. The bevelled edge makes it easy for the installers to use a plaster to smooth out the surface after nailing the sheets to walls and ceilings as well as taping the edges.

The plasterboard comes in different types. Although various manufacturers provide a unique name for their products, but they’re all included in one of the following categories:

• Water Resistant Plasterboard - This type of plasterboard are best suited to be used in water areas like bathroom, laundry rooms and kitchens.

• Acoustic Plasterboard - Due to its sounding proofing qualities, this type of plasterboard is preferred to be used in home theatres or noisy areas.

• Flexible Plasterboard - This is to be incorporated on curvy surfaces.

• Fire Resistant Plasterboard - Just like the name implies, this type of plasterboard is best suited for use in high fire hazard areas.

If you’re about to kick start some small renovations around your house or office, using a plasterboard to clad your walls is a very simple and worthwhile task. However, if you want to do major renovations or need to apply plasterboard to your ceiling, the best option would be to leave it to a seasoned professional.

A boiler is simply the most important part of a central heating system as it generates the heat that warms up the home or property. Basically, the appliance or small furnace makes use of gas, LPG or oil in order to fuel its operation. However in the UK, most boilers are usually fuelled by natural gas which is supplied automatically from the national gas grid. And depending on how it operates, there are various types of boilers.

Typically, a gas central heating boiler will have multiple pipes entering from underneath. While one pipe supplies the boiler with gas from the mains gas supply, another pipe allows cold water to enter the boiler to be heated, the last pipe then enables hot water to exit the boiler so it can be distributed around the home.

✓ There are fuel jets and heat exchangers inside the boiler. When the heating is turned on, a valve is opened to allow the mains supply gas to enter a sealed combustion chamber in the boiler. There are multiple little valves which permit the entry of the gas before being ignited by an electric ignition switch. These jets heat a metal component in the boiler known as a heat exchanger which works to transfer the heat to the cold water pipe and heat up the water.

✓ Once the water has been heated to the target temperature, it’s then pumped through a circuit of pipe which runs around your home by an electric pump.

✓ The heated water enter each radiator, is then transmitted via a closed loop and radiates heat into each room.

✓ Once done travelling through all radiators, the water then returns to the boiler at which it must have been cooled. Therefore, the boiler will have to reheat following the same process before circulating. The water can only be drained by a professional Gas Safe engineer

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

Over the years, UPVC spray painting has grown to become a standard practice. Previously, what was done when people wanted to change the colour of their UPVC window is simply to replace the old ones. However compared to the cost of replacing the units, it’s actually a lot easier to simply have your UPVC windows sprayed and even more importantly, at just a fraction of the replacement cost. If you’re thinking about spraying your upvc windows, then you’ve come to the right place! In this post, we’re going to take you through the entire process. However, if you lack the confidence needed to pull this off, we’d strong advise that you get in touch with a professional to avoid make costly errors or mistakes.

The first step to successful upvc window spraying is always to make sure that the upvc is properly cleaned by removing any loose dirt and residue, getting rid of any muck and grime which has developed over the years. You can also abrade the surface in a very light manner to leave upvc frames with a key to make the paint adhesions stronger. Once you’re done with the preparation, the obvious next step is masking off. This process requires you to protect the walls, glass, floors and brickwork from any potential over spray. To achieve this, you can make use of masking papers.

Upon completion of the masking off process, then its time to spray paint the upvc windows using a spray gun and spray painter. This requires a lot of practice as it could be very dangerous as you can inject yourself with paint, which can be seriously fatal.