Find a Shop Fitter you can trust in Beaconsfield.

Is your garage door a bit old and outdated? Are you planning to make some renovations? Or perhaps you just want a newer and more stylish garage door, that’s safer and easier to operate, installed. Fitting a garage door can be a bit tricky but it’s not as difficult as you might think. If you’re without proper training or experience, it’s advisable to get in touch with a reliable professional for help in order to guarantee the best results while also saving you both time and money. This guide offers you step by step instructions to assist you in the installation of a new door on our garage.

To get started, the obvious first step is to remove the old garage door. Carefully go through the manufacturer’s instructions to achieve this. Here, you’d basically have to unlatch the door, take apart the door’s panel and unscrew the tracks.

lMeasure, Fit The Hinges & Handles

• Take a measurement of the area in which the door will be fitted

• From the top of opening to ceiling should include a space of about 10 to 12.

• For the length of the garage, you should have the door’s height with about 18 or more space.

• Once done, attach stops to the sides of the opening

• Lay out the bottom piece of the door and include the weather stripping (if you deem fit) using the sawhorses.

lPut The Bottom Piece In Position

• Fit the bottom piece into door frame using a level

• Hit nails partway into each jamb

• Bend the nails slight to secure their position.

• Assemble the vertical, curved and horizontal pieces of the track using the manufacturer’s instruction

lFit The Remaining Panels

• Put the second panel on the first panel

• Use a hammer to hit nails into it

• Fit the hinges.

• Repeat the process for the number of panels required and achor individual piece into the door jamb.

lInstall Rollers

• Fit the rollers in the section’s supports

• Put the rollers in the assembled track and make sure they’re not pressed to tightly against the track to prevent friction.

lSecure Tracks & Fit The Springs

• Fit the curved and horizontal pieces

• Assemble the springs following the manufacturer’s instructions

• Ensure that the tracks are level and parallel by lifting the door to about half length

• Lift the door to cover the distance left and fit the springs to the pulley system

Laying of floor tiles may seem seem to be a very tricky task that’s beyond the abilities of some homeowners, but in reality, it’s a task that most DIYers can handle - as long you don’t rush the process. With a little patience here and there, you’ll be amazed with how far you can go. The materials are quite easy to work with and tools, only requiring a little practice to master. However, if you don’t have the necessary confidence to pull this off, we’d strongly recommend that you call in a professional who can guarantee the best results for help. In this guide, we’ll walk you through the process of laying floor tiles.

• Floor Preparation

✓ The first step is to prepare the floor by moving all objects like mortar, adhesives and more.

✓ Use concrete patching compound to fill ill low spots and cracks, until the floor is levelled.

✓ Ensure the floor is dry and clean.

• Pattern Layout

✓ Take the measurement of each wall’s length while also taking into account the room’s diagonals.

✓ To help place the tiles in an orderly manner, make use of a chalk to mark down lines on the levelled surface in question and ensure it’s parallel to the walls.

• Adhesive Preparation

✓ Mix the appropriate amount of water with the adhesive (bonding agent).

✓ The mixture should be toothpaste-like thick to ensure the durability of the tiles.

• Tiles Placement

✓ Depending on the tile’s size, evenly spread the mortar on the floor using a notched trowel.

✓ Lay the first tile on the bonding agent (adhesive or mortar) and apply a gentle and little pressure on the tile.

✓ Repeat the technique for other tiles using plastic spacers to ensure the edges and corners are properly aligned.

• Tiles Cutting

✓ Cut the tiles (if necessary) with the help of a wet saw or scoring cutter featuring a diamond-tripped blade.

• Grout Application

✓ Filling of the tiles’ gap is done using the grout. It can be applied to the joints with a rubber float.

✓ After application, allow the grout to set up for some minutes.

✓ Use sponge and a bucket of water to clear out any adhesive leftover.

• Grout Sealing

✓ Use a foam brush or applicator bottle for the sealants’ application.

✓ Clean out excess sealer within 10 minutes.

Do you want to know the level of thickness a driveway concrete slab should be? Well, you are not alone! So many other home owners ask this question on a regular basis and reasonably so. In order to prevent cracks on your concrete over time, it’s crucial to ensure an even thickness across your driveway concrete. To determine the necessary thickness of your driveway concrete, there are some questions that must be answered. These includes:

• What’s the number of vehicles you expect to have on your driveway?

• Do you plan on parking heavy, industrial vehicles on it?

For a standard passenger vehicle driveway, you’d have a driveway spanning 8 to 9 feet in width as well as 15 to 18 feet for double width. The thickness for this type of driveway concrete is usually 4 inches of non-reinforced pavement. Ultimately, this enables you to park everyday family cars on it without having to worry about it cracking due to the car’s weight. Also in order to prevent cracks, it’s expected that the driveway should be sloped towards the street as this would make sure that there’s a run off of water especially for areas that experience lots of flooding. In addition, there’s also the need to install joints to prevent cracking. For the standard 4 inch thick driveway, these joints should be positioned about 10 feet apart.

Finally for parking heavy industrial vehicles, your concrete driveway is expected to be thicker in order to cope with the added weight. Typically, the concrete driveway will require a thickness of about 5 inches. The additional one inch may not sound much, but the fact is this can increase the load carrying capacity of the concrete driveway by up to 50 percent.

Most of the people out there do not know the difference between a carpenter and a joiner. This is a very common question that is asked by many as to whether there is an actual difference between the two.

Both joiners and carpenters have many shared traits. The definition seems to change throughout the UK. The southern parts use the term carpenter whereas the north seems to prefer the term joiner. Both of these trades involve working with wood mainly in the construction industry. Both of them are, however, are two very unique and separate trades. Both of them come under the broad term of ‘carpentry’ however their skills and specialisms differ.

A joiner is defined as a trained craftsman who is responsible for making or joining wood in a workshop. On the other hand, a carpenter is a professional that works on site with the timber. In summary, a joined creates the wood back at the workshop while the carpenter fixes them on site. A joiner, therefore, works on things that are done in a workshop using machinery while a carpenter is responsible for its assembly on site.

As both joiners and carpenters had learnt the basics of both trade while they were practising as an apprentice, several similar overlaps are bound to occur.

It is good practice to ask the company or the individual what trade they specialise in. As an example, a joiner may be able to make a particular item whereas a carpenter may be better doing the actual fitting.

It is evident from the above sections that carpentry and joinery are completely different and therefore, should be categorised under two different trades, however, there is indeed a lot in common in their extremely high skilled work.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

Leaves, twigs and moss all have something in common which commonly frustrates house and homeowner - they are the 3 major materials that adversely impacts the correct performance of a roof guttering system. The major reason for water drainage issues for many houses as well as buildings are these natural products. Wondering just how some leaves as well as few branches can trigger such a big problem? Over time there'll be a progressive build up of the all-natural debris in your rain gutter system which begins to rot and also count on a thick as well as sloppy goo which blocks the flow of water in your water drainage. Consequently, there's the demand to make sure that your rain gutters are completely cleansed at least twice every year in order to protect against larger issues that can be triggered by the obstruction of a drain system.

So if you're thinking about obtaining your rain gutters cleaned by a specialist, you 'd probably want know simply exactly how it's going to set you back. Well, there's not uncomplicated and straightforward answer to this question as there are a number of variables that adds to the final cleaning expense of your rain gutters.

In general, in the UK, the ordinary cost for cleaning of seamless gutter is generally around ₤ 18 to regarding ₤ 25 per hour. Nevertheless, you can additionally be priced quote a day price which is usually ranging between ₤ 150 to ₤ 200 per day.

The variables that can affect gutter cleaning rate includes the sort of your home (such as a terraced, end of terraced, detached as well as semi detached houses) which has a differing seamless gutter cleaning rate greatly as a result of their dimension differences, the height of the building (if you call for the service for a building situated on the second floor of a building, this would certainly be a little bit higher than if it were to be on the first stage) as well as added requests.

Several individuals think that the the way their air conditioning system works is simply by pumping hot air out of their homes or offices, blowing a cool air in return. This is absolutely wrong! The hot air is, in fact, cycled back in as cold air and this process continues until the thermostats gets dropped down to the required or set temperature. The air conditioning system manages this in a similar way to how the refrigerator manages to stay cold and of course, excluding the insulated box.

The short and simple answer to the question of what gas an air conditioning use is Freon. This is a non inflammable gas which is subjected to the evaporation process over and over again in most refrigerators to keep the temperature at a low level. This same process is repeated in air conditioning systems. Now let’s take a look at how the Freon gas is incorporated in AC systems.

The cold Freon gas is firstly compressed by a compressor in the air conditioner. The gas is then combined with a little quantity of oil in order to lubricate the compressor. When Freon gas is compressed, the pressure is increased which makes it incredibly hot. It then moves through a couple of coils which works to lowering the heat and turning it to liquid. This Freon liquid will then be transmitted via an expansion valve which causes it to cool down until evaporation takes place. The outcome of this is a low pressure cold Freon gas which is then transmitted via another set of coils allowing the gas to collect the heat and lower the air within the room.

The air conditioner now filters the air and clears out the dust, smoke, pollen and other kinds of air pollutants. The system also absorbs excess liquid from the air too which it uses to cool down the system and pump it through a hose.