Find a Shop Fitter you can trust in Knutsford.

A lot of an uninsulated property’s heat is lost through the roof and that’s even more alarming, when you realize this figure is up to a quarter of the total heat of the house. Hence, the tremendous importance of preventing this heat loss through loft insulation which will go a long way to help you against spending unnecessary thousands of pounds on heating bill as well as energy loss.

Loft insulation is an effective method to achieve the desired result, however the question is, how exactly does it work? Well, it’s time to find out!

Using either a fireplace or central heating to heat up your home, a large quantity of that heat would be lost through the roof of your home. Generally, heat rises and when it does, there’s simply no way to prevent it - it’s just science. Escaping by both the conduction and convection methods via your roof, the heat escaping through your ceiling, into the loft space and out into the open air outside can only be significantly reduced by laying loft insulation.

Generally, the added layer of insulation works by trapping the heat inside the room below the loft so as to enable the air within your house to stay warmer for longer. What’s more? The layer of insulation also keeps cold air from the outside from entering your home. As a result, you don’t have to heat your home as much in order to achieve the same temperature for each individual room. Over time, just by doing this you can potentially save hundreds pounds. Getting it installed in your home may actually seem a bit expensive at first, but it’s something that’ll eventually pay off.

A real headache is having graffiti on brick. This material is porous which enables paint to sink with ease inside all of the surface’s grooves. Unlike wood, they can’t be scraped and if it happens to be an internal wall, it can’t be sand- or water-blasted. Here, chemical and gel masonry stripper are your best bet. And while stripping of the brick is not a complex task, it does involve a number of applications of stripper and multiple scrubbing which makes it very time consuming.

Basically, a fresh and wet paint should be soaked up with am absorbent material without wiping the paint in order to spread the stain. Once done, you can then proceed to apply a suitable solvent like white spirit. After this, wash the area using a degreasing agent taking care in the disposal of the run-off material.

With dried paint, simply scrape off the paint as far as possible and apply a paint removal using the following steps:

• Put on your safety gear like a face mask, safety googles and gloves.
• Apply the paint stripper over the brick wall with a brush starting from a corner at the top of the wall and then working outward and downward.
• Leave for the specified amount of time by the manufacturer. Then start to scrub off the masonry paint stripper beginning at the top of the wall again. Remove as many paints as possible.
• Use rags and warm water to wash the brick wall and allow it to air dry.
• Repeat the process over again to remove every form of stubborn paint that’s left.
• Use a white vinegar to spray the stripped brick wall and wipe off any residue of paint with a brush and rinse with water.

How To Install Bifold Doors

If you’re looking to install a bifold door in your home or property, then you’re at the right place! In reality some jobs are better left to the professionals and one of such jobs is bifold door installation especially if you lack proper training and experience that’ll guarantee the best result the first time. If otherwise, hiring a professional installer will do you lots of good like saving you time and extra money that could result from costly errors. In this step by step guide, we’ll take you through the bifold doors installation process.

The first step to take when it comes to bifold door installation is to take the measurement of the door opening and get a kit in the appropriate size. For a better accuracy, do note that the combined measurement of both doors should be about an inch less than the opening’s total width while also being two inches less than the door frame’s height.

• Install the top rails in such a way that the rail’s end makes contact with the door frame’s side using the screws.

• Fit the bottom rail in the same fashion as the top ensuring the rail’s end makes contact with the same side of the door frame.

• Insert dowels into the predrilled holes in the door panels’ top.

• Place the dowel with the adjustment screw near the bottom’s side wall. While placing the fixed dowels in the door panel’s top and bottom on the side farthest away from the hinge. Once done, put the dowel and spring assembly into the door panel’s top, closest to the side wall.

• Fit the door panels into rail’s top and bottom while also adjusting the screws to centre the doors.

• Ensure the doors open and close like they should. If positive, tighten all hardware and fit the pulls or knobs of the door.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

You must use a builder or scaffolding outworker who is skilled and knowledgeable to put up scaffolding. This means they require to have the essential skills, knowledge and familiarity to be able to accomplish health and safety. A capable scaffolder will hold an effective Construction Industry Record Scheme (CISRS) Card – it is up to your agent to check that this person is capable before any work begins.

When should scaffolding be checked for safety?

According to the law, the user of the scaffolding must check it to ensure that it is safe:

• Before they first use it

• After every seven days after putting it is up

• After any alterations, or damage due to extreme weather conditions

When do you need scaffolding?

It is up to your trader to evaluate the level of hazard and use a suitable apparatus. Repairing or replacing a single tile is never going to be same as installing solar panels that are high up 30 storeys high. Everything is dependent on the type of work and the risks involved. Traders need to guarantee that their staff will remain safe as they work on your property. This means working from the ground if possible. If they need to work at higher altitudes, they must minimise the danger of falling by using present safe roof zones or scaffolding.

You wouldn’t need a license if your builder has to put up scaffolding inside your property premises. However, if the scaffolding has to go out on the pavement or anywhere outside your premises, your builder or scaffolder needs to get a license from the building council.

Insurance

Scaffolders face an inimitable set of hazards due to working at high altitudes. Builders or scaffolding organizations require insurance that covers those risks, together with public liability insurance to cover any damage to the public triggered by falling items from the scaffold as well as employers’ liability insurance to cover their persons if they are wounded while working at height. This is an important thing to check before any other work begins.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.

Installing wooden flooring is a quite simple process, however to get it right the first time, there are very essential preparations that must be made. These includes determining the site is in the best condition before installation, removal of all floor coverings and underlay for a more stable and durable installation and incorporation of the right expansion gap of about 10mm to 12mm which would be maintained around the floor’s perimeter.

Wooden floor fitting can be done on two types of sub-floor - Concrete and Plywood. To install onto concrete, you can follow the guide below:

• Incorporate flexible wood on concrete adhesives.

• With the help of a 3mm toothed trowel, spread above 2 board widths of adhesive along the starting wall sub-floor, beginning at a corner of your room.

• Position the first row of flooring into the area that is glued using the tongue facing opposite the wall.

• Put 10mm spacers against the wall to see to the consistency in expansion gaps.

• Make sure the joints are at a minimum of 150mm apart from the first row when fitting the second row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

To install onto plywood, you can follow this guide:

• Make use of a porta-nailer.

• Position 10mm spacers against the wall - parallel with the installation direction.

• Fit the first row using the tongue facing opposite the wall and with the help of the porta-nailer or flooring nailer.

• Lay the second row and make sure the short end joints are at a minimum of 150mm apart from that of the first row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

Click here to learn more about wood flooring.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.