Find a Shop Fitter you can trust in Lostwithiel.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

The most serious form of fungal decay is dry rot which occurs when the moisture levels of a timber is about 20 percent. It targets timber in buildings and feeds off the part of the wood which gives it its strength.it is able to produce moisture through the digestion of timber and as a result, does not require any source of moisture to spread. Once the dry rot is able to spread, it can severely impact and compromise the structural integrity of the house or building. If you think you may have dry rot on your building, the best solution would be to call on a professional to conduct a survey of your premises and have it treated as soon as possible if positive. If the dry rot is not identified and treated as soon as possible, you may have to remove and replace all the affected timber later on. In this post, we’re going to take you through the process of treating dry rot by yourself. Let’s take a look!

• The initial treatment stage of dry rot is to identify the moisture source and have it repaired. Once done, you’ll have to ascertain the full extent of the dry rot outbreak. To achieve this, simply open up the affected area by removing the plaster and render in all directions while also removing flooring and lifting floorboards. Once done, you should be in the best position to determine the full extent of the infected timbers.
• Proceed to cutback the timbers in-situ to a minimum of 500mm beyond the last signs of fungal growth or the strands of hyphae.
• Remove all fruiting bodies and detectible spores. Clean the wall areas to eradicate surface growth using a stiff brush if necessary.
• Replace the timber with pre-treated timber.
• Treat the new and old timber with a dual purpose dry rot treatment fluid and sterilise the masonry.

If you’re interested in getting a new air source heat pump, then you’d probably want to know if they’re really advantageous, cost effective and efficient. The fact is, there are a plethora of benefits that comes with using heat pumps which is a renewable alternative to warm up your home in the UK.

An air source heat pump can help you save money on energy bills while also minimizing your carbon footprint as compared to a gas or electric heating system. Another important benefit that comes with air source heat pump is the fact that they’re quire versatile and yet affordable. Generally, they can function either for heating or cooling purposes and they can also be incorporated for either heating of space or water. In fact, in order to achieve the target Net Zero by 2050, the UK government are looking to fit 19 million heat pumps in new builds. With significant rise in the deployment of heat pumps, the grants by the UK government enables this renewable energy source to become a lot more affordable to run while also helping to minimize the burden of the air source heat pump cost.

As perfect as it seems, this renewable source of energy also comes with a number of disadvantage which we’re going to list out. Let’s take a look!

• There must be sufficient space outside the house to accommodate the external condenser unit.
• The condenser unit can make a lot of noise and even blow colder air into their immediate area.
• Since they consume electricity to operate, this also means they’re not zero carbon unless the electricity is produced from a renewable source like solar panels etc.

How Do Bifold Doors Work

Generally, bifold doors are modern styled doors that are able to create a grand entrance and catch any visitor’s attention almost immediately. Unlike the conventional sliding doors, they are way more practical and convenient which makes it an awe-inspiring home addition. However, with the design being relatively new when compared to its counterpart - the sliding doors, not everyone knows about how they work. Therefore, it’ll only make sense to discover more about this door design before deciding on its utility. So how does a bifold door work?

The bifold door ( both interior and exterior types) operates on a built in tracking system that runs along the glass panels and connected on a train. In other words, the doors fold in and then slowly and smoothly glides over the laid out track which is backed by a chain of wheels or a tracking system. This function is carried out in a smooth and quiet manner, irrespective of the medium of movement.

Now talking of the bifold structures, they mostly come in pairs especially the interior designs. The design can either be in form of two doors that can be folded to one side or four individual panels that can be opened from the centre while some of the doors will fold on each side. Typically, the tracking will feature these units as well as the other important fittings, and also open inwards or outwards.

One of the significant qualities of these doors making them a popular option amongst homeowners nowadays is the flexibility and versatility of these units as well as their effectiveness when it comes to saving space. You’d be surprised to know that some of these bifold door designs can feature up to 7 panels which are linked via hinges and connected to the top or bottom of the roller track.

If you’re replacing your carpet with new carpet, you might be able to use your old underlay. This is dependant on how long the existing carpet has been down for and also the condition of the underlay. But if you’re getting wood, laminate or vinyl flooring it’s not suitable. It will put stress on the joints if you use underlay.

Aluminium conservatories are really easy to maintain, making them a top choice for many homeowners. Unlike wooden conservatories, they don’t need regular treatment to ensure they don’t deteriorate.

The most you’ll need to do to keep your aluminium conservatory looking great is give the frames and glass an odd wipe with water and a mild detergent to get rid of any occasional dirt.

Often referred to by many as the holy grail of home improvements, house extension comes with a wide range of benefits which makes it easy to see why the extension could be a great uptick in the potential price of your property in terms of sales. So if you’re looking to build a new home extension but still not convinced about the project, we’re here to help you. Being fully aware any home construction work is usually a heavy investment, there’s a huge need to be set on your decision before scheduling the commencement of any work. So are house extensions worth it? Below are some of the top benefits offered by house extensions to help you decide if it’s the most suitable route for you.

• Add To Your Home’s Value

Building an home extension is a great way to add value to your home before selling. Increasing the living space of your home is an incredible appeal to many buyers which significantly increases your property’s total value. However, you must ensure that the extension is impressively designed using top quality materials in order to generate more value.

• Good Alternative To House Moving

The most common reason for moving is usually due to a lack of sufficient space, but with house prices steadily on the increase a cost effective alternative is highly sought after. This alternative is house extension which creates more space for the household to spread out and have more privacy.

• You May Not Require A Planning Permission

You can extend your house and still not need to apply for a planning permission. To achieve this, simply comply with the laid down rules set under the permitted development rights.

• Extra Living Space

If you fill you’re starting to outgrow your existing structure and do not buy into the idea of moving, then your best bet might just be to extend your home.