Find a Shop Fitter you can trust in Magherafelt.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

After making the decision to refurbish your home or property, the next obvious step is finding the right builder to get the job done. The process of getting a good and reliable builder can be a very tricky one especially when you don’t plan ahead. And in truth, the outcome of your house refurbishment project can only be as good as the contractor your hire. Consequently, finding the perfect builder for your task should be a top priority to get the best return on investment. Here are a few sources that will put you in the right direction to finding a reliable home refurbishment company.

✓ Friends, Relatives & Neighbours

If you have a friend, relative or neighbour that have recently completed a home refurbishment project, you can go for a visit to check out the work done. If you’re pleased with the work, you can proceed to ask about the work ethics of the builder and get the contact if satisfied.

✓ Internet

With the rapid rise of online technology, there’s hardly a service you can’t find on the internet. Websites like HomeAdvisor have been helping people find their desired service providers with relative ease for so long. To get the right building contractor online, it’s advisable to check reviews as well as testimonials before moving forward. Nowadays, you’re most likely going to find so many positive online reviews as some businesses now go to the extent of dubiously writing good reviews for their companies. As a result, it’s recommended to pay closer attention to the negative reviews and check if it’s something you can cope with before hiring a contractor.

✓ Store Contact Lists

You’ll discover a long list of building contractors on several stores trading building materials. These builders may not be affiliated with the store owners, but many stores see it as their responsibility to point you in the right direction so that the building materials acquired from them can be put to good use.

This is one of the most common questions when it comes to upvc windows. If you’re also interested in knowing the possibility of spraying white upvc windows grey, then you’ve come to the right place! In this post, we aim to answer this question once and for all.

The short and simple answer to this question is yes, you can definitely spray white upvc windows grey! In fact, you can spray white upvc windows with any colour of your choice. So far, the most used colour is the anthracite grey, but you’re not restricted to that. You can also make use of agate grey, French grey, window grey, battleship grey and lots more! However, it should be noted that spraying white upvc windows grey is in no way an easy task as it requires lots of experience and practice.

The spraying process usually starts with a thorough cleaning of all the surfaces to be sprayed using a specialist solvent upvc cleaner. Once done, you’ll have to get rid of any existing silicone from around the frames because the paint won’t adhere properly to silicone. Upon completion, you can then proceed to masking up the surrounding brick or stone, glass, openings into room, furniture, paths or plants and many more to protect them from potential paint overspray. Now to spray the paint, you can make use of a spray gun and spray painter. Before you start painting, you can apply a light dust or mist coat to identify any contamination left on the surfaces. Once this has dried without any negative reactions, you should spray two further coats (some colours may require up to 3). leave for up to 20 minutes to dry and remove all masking.

There are several different kinds of plastering. ‘Dot and dab’ refers to a base layer of plasterboard which is attached to a wall using ‘dabs’ of adhesive. ‘Floating’ is a technique where a backing or undercoat plaster is applied to walls. ‘Skimming’ or ‘reskimming’ refers to the very thin final decorative layer of plaster.

When Does A Loft Become A Habitable Room?

When a loft is being converted to functional space, there are a multiple options it can offer. It’s not uncommon that at the conversion of this space, many household may not have a specific plan on how it’s going to be used. However, they know later on an actual need might arise, perhaps as you start working from home, developing other hobbies that requires an extra space or the family grows.

The loft can easily be converted into a game room, study room, playroom or even a household’s “breathing space etc. However, when the family grows and you wish to make use of the space on the top of your home as an extra bedroom, there are many factors to consider. The fact is, just because there’s enough space to fit a bed, doesn’t make it habitable. For a loft to become habitable, it must be built specifically for the purpose of being a sleeping area and must also comply with the relevant building regulations. It’s as a result of this, many property sale particulars include “potential third bedroom, subject to regulations statement written on it as well as the boarded and insulated loft space’s dimensions.

Loft conversions building regulations are set in such a way to ensure that adequate attention is given to both safety and structural elements to build a new space that’s fit for undetermined household use. These regulations are established minimum requirements to guarantee the following:

• The new floor and ceiling’s structural integrity.

• The existing roof and party wall modification’s structural stability.

• Safety during fire incidents plus an escape route.

• An appropriate stairway access.

• The proposed changes’ structural suitability to the external environment in association with the local area as well as any unique factors specific to the property.

There’s a need to ensure that all the paperwork are in place,before putting your house up for sale on the property market. An very good example of such essential document is the Electrical Installation Certificate (EIC) which is used as a proof to attest to the fact that the electrical installation works carried out on the property in question was actually done and also whether or not it satisfies the building regulations. It’ll be a contravention of the law to put your house up for sale or actually sell it without producing this important document. Therefore, if you’re looking to sell your house you may wish to know the electrical documentations you need to complete the task. In this post, we aim to provide you an in depth insight into the electrical certificates needed to sell your house while also helping you make informed decisions along the process. Let’s take a look!

You’ll need to obtain two certificates in the event whereby the electrical work done was performed by a registered and qualified electrician. The two documents include:

• The Building Regulations Compliance Certificate - This is provided to confirm that the electrical works done complies with the Building regulations.
• The Electrical Installation Certificate (EIC), alternatively you can have a Minor Electrical Installation Works Certificate which is provided to confirm that the electrical works done satisfies the BS 7671.

In addition, the local building control body must be provided with a copy of these documents. In such an event whereby the electrical work was completed after 2013 and either it was done by yourself or by an individual who isn’t a registered professional, then there’s a need to make sure that work is inspected by a registered third party certifier within 5 days of completion. If the work is found to be satisfactory, you’ll be issued a copy of an Electrical Installation Condition Report.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

Are you about to replace your old windows and wondering just how much it’ll cost to have a new one fitted? If yes, then you’ve come to the right place! The question is a very straight forward one, however a direct answer can not be provided as determining window prices for a replacement project can be a very tricky challenge. With a plethora of influencing factors that can play a key role in the price of both materials and labour to be used, it could be extremely hard for a window installer to provide a cost estimate without paying you a visit beforehand.

The factors that can go a long way in determining the price of your new window includes the size of the window, frame material, style chosen, your location, rates charged by the window installer (these rates can be different from an installer to an installer, so it’ll probably be in your best interest to compare quotes to identify the most competitive price) as well as the type of glass required.

Generally, for a small flat featuring four windows, the average cost for new windows would be between the range of £2,100 to £2,300. This range provided covers the cost of double glazed uPVC casement windows as well as the installation price. In the same tone, a home with up to 8 windows will have an average cost for window replacement between the range of £4,400 to £4,600, wile also taking into account the installation price. Whereas a house comprising 10 windows could begin at an average cost of window replacement between the the range of £5,200 to £5,500, and a 15 window home will be between the range of £8,400 to £8,600. it should be noted that the aforementioned figures only include the standard number of windows with a uPVC frame and the installation cost.