Find a Shop Fitter you can trust in Kingsbridge.

Solar panels can be pretty expensive, so require an initial investment. However, a quality solar panel installation can be very financially beneficial, saving you money in the long run. It does this in two main ways.

Firstly, using electricity generated by your solar panels means that you have to use less power from the national grid. Once you’ve bought your solar panels, your solar electricity is essentially free, meaning that you’re saving money by using this instead of power supplied by your energy company. If you want to maximise these savings, invest in a solar battery so you can store unused solar electricity ready for when you need it.

You can also earn money with your commercial solar panels through the Smart Export Guarantee [https://solar-panels.quotatis.co.uk/smart-export-guarantee/]. This is a government scheme that says that all licenced energy suppliers with 150,000 customers or more have to offer a tariff to renewable energy generators. When you generate solar electricity but don’t use it immediately it gets fed back to the grid – the tariff pays you for every kWh of this.

At the moment there’s no minimum tariff that an energy company has to offer – it only has to be above zero. However, many energy companies are competing to offer the best deal, so you can definitely find a tariff that will pay you for all the unused solar electricity you generate.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.

• Don’t buy cheap solar panels – while it might seem tempting, make sure you choose MCS-certified solar panels. Any reputable installer will recommend high quality solar panels, which is another reason to have them professionally installed rather than doing it yourself.
• Ensure that your installer uses non-combustible mounting systems and frames.
• Check your system regularly for signs of pests gnawing through cables.
• Keep your solar panel system regularly maintained with proper testing and servicing carried out as recommended by your installer.
• If something doesn’t look right to you, get in touch with your installer and ask – they should be more than happy to help.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the ours so that you can find quality tradespeople and see genuine reviews from previous customers. Not all online review sites can be trusted to display real reviews.

The process you need to go through to install a TV aerial depends on the type of aerial you have. If you have an indoor aerial, it’s simple. Just plug the aerial into your TV and stand it up next to it. If the signal isn’t right, then try moving your aerial closer to a window or higher up. Make sure you rescan for channels every time you move it so you know if you’ve made an improvement. It’s also fairly easy to install a loft TV aerial – just take it up into your loft and position it in a convenient place. Again, experiment with angles and positions to ensure you get the best signal. Installing an outdoor TV aerial is a little trickier. Ideally, try to fix your aerial to a wall or chimney at a gable end – this will be much easier to access than a chimney in the middle of the roof. Follow the instructions that come with your aerial for mounting it – it’s usually best to lash your aerial on rather than use screws. If you’re not used to working at height or aren’t confident doing your own aerial installation work, it’s best to get in touch with a professional.

Are you thinking about updating your bathroom? If yes, then you’d probably want to know how to go about it. Well, when it comes to bathroom remodelling, the process always begins with the drawing of a floor plan. If you don’t know how to go about that, then you’ve come to the right place! In this guide, we’re going to take you through the bathroom floor plan drawing process. Let’s take a look!

First and foremost, you can make use of the pencil and paper approach as it happens to be much cheaper than the computer based approach. Plus, you don’t have to be an art genius in school to complete the task satisfactorily.

1. Sketch it out. Create a rough sketch of the space on unlined paper. This should feature all openings like the doors and windows, the spots where the existing plumbing fixtures are located, the location of the electrical lines including outlets, receptacles, heating and cooling pipes and more
2. Add dimensions to the sketch. The next line of action would be to take measurements of the bathroom. With the help of a friend, hold the tape tightly at both ends in order to get the right dimensions. Then, measure the length of the walls, fixtures, windows and mark then roughly on the sketch. Once done, you can go back to double check the recorded measurements for accuracy.
3. Transfer the room dimensions to a sheet of graph paper. At the stage in the process, you should be aware that each 1/4 inch square on the graph paper is equal to 6 inches or half foot. You can start by drawing the bathroom walls and partitions as well as the surrounding areas. Then, add the doors and the direction they swing open and the windows present. Once done, draw the fixtures to complete the floor plan.

When it comes to laying of bricks, it is essential to get the right mortar mix. It is vital, be it for construction or maintenance projects, so far mortar is required. There are several materials incorporated in getting mortar which includes both cement and sharp sand, soft sand or plasterer’s sand and lots more. Here, we are going to look at the right ratio for cement and sand mix in bricklaying.

Cement include ingredients such as iron, aluminium, as well as silicon and it is mainly used for mortars like aerated cement mortar, Portland cement mortar and gauged mortar. Sand, on the other hand, comes in different forms such as sharp sand, soft sand and plasterer’s sand. The sharp sand consists of a larger grain size than the others and is usually incorporated in the construction areas that requires more strength as well as flexibility. Soft sand is the most common one used in mortar and it’s also referred to as bricklayers’ sand. These are used to make all types of mortar. Finally the plasterer’s sand which neither has the sharp sand’s coarseness nor the fineness of the soft sand, but can also be used for any form of mortar.

Cement and sand mortar is used for a plethora of bricklaying jobs serving as a glue for bricks, walls and pillars, while also repairing or maintaining old listed buildings. The preferred ratio here is 1:3 to 1:5 of cement and building sand. Meanwhile, to get a sand cement mix, essential materials that are required includes water, soft building sand as well as cement. However, you must also note that a sand and cement mortar is not used for structural projects, rather a concrete ratio is used.

There are lots of paints that are suitable for different areas of your property. In general, gloss and eggshell paints should be used in high traffic areas, whereas matte paints are suitable for lower traffic areas. Professional painters and decorators can give you advice on the most suitable types of paints.