Find a Shop Fitter you can trust in Totnes.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Electric heating has several benefits. It can be paired with renewable electricity generation, so the electricity used to heat your home will be sustainable. Underfloor heating is very efficient and can be cheaper than comparable gas or oil fired systems.

You can technically install an electric range cooker anywhere, as long as it’s not in a room containing a bath or shower. Wherever the cooker is, it should be in area with: Cooker, No draughts, sufficient air supply. If you are redesigning your kitchen, check with the designer on where best to locate it.

The short and simple answer to this question is yes, just like other new extensions, you must have a foundation done for your lean to conservatory. In order to transfer the building’s weight to the floor safely, there’s a need to construct a foundation. Without it, the structural integrity of the extension would be heavily compromised. What’s more? While there’s no minimum depth requirement for a lean to conservatory, there are multiple factors that can affect the depth as well as type of the foundation. Let’s take a look!

• The nearby trees. What trees do is to absorb water from the soil which can affect the foundation significantly. When water is absorbed from the soil, the soil shrinks which affects the foundation’s strength. The size as well as type of the tree will determine the extent of the water absorption from the ground.
• The soil’s suitability. The weight that each soil can withstand varies and even more so, when environmental factors have more effect on certain types of soils than others. For instance, chalk is able to drain water away relatively easily which means that nearby trees will only have a little effect on its quality. Clay, on the other hand, shrinks when drying and also retains a lot of water. This means that nearby trees will have huge impact on clay soil which will compromise the structural integrity of the lean to conservatory. Therefore, since changes to clay mostly occur to about 0.75m depth, foundations on the soil should be constructed deeper to compensate.
• Undisturbed ground. Before the foundations are laid, there’s a need to identify grounds that hasn’t been built on and this usually takes a depth of about 1m (this figure may vary especially in regions where drains have been laid).

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

The vinyl material is a very popular flooring material preferred by several home and property owners as it happens to be slip resistant, easy to clean and also waterproof. As a result, this type of flooring is perfect in bathroom, kitchen and other high traffic areas within a home or property. Now, most home owners wonder whether or not it’s possible to use underfloor heating under vinyl floor. If you’re also looking for answers, then you’ve come to the right place! In this post, we’re going to consider the possibility of fitting underfloor heating under vinyl flooring.

The short and simple answer to this question is yes, you can safely use underfloor heating under vinyl flooring. A bunch of studies has been carried out by flooring experts to get a better insight on the effect of underfloor heating on vinyl floor’s physical and aesthetic appeal. It has been made known that there’s no shrinkage whatsoever or any form of impact on the physical appearance like discolouration and more. As a result, underfloor heating has no impact on vinyl flooring.

In order to ensure a perfect heat output, there’s the need to obtain a heat loss calculation when selecting a heating system. It’s always advisable to get an Energy Star approved programmable thermostat which offers you a full control of your property’s heating settings. It also enable you to live in a warm room when you want to without having to waste heat energy.

Generally, all wet underfloor heating systems are fitted on the structural sub floor. This implies that all products within thee wet system range can be incorporated safely with vinyl flooring.

As a home or property owner, you’re generally allowed to build next to your neighbour’s fence as long as it’s on your own side of the property. With that in mind, there are certain laws that regulate how close a fence can be built to buildings on the same lot or neighbouring lots. In addition, there are also local bylaws that provide limitations on the placements as well as height of fences so as to address safety hazards. In this post, we’re going to give you a good insight into how close you can build to your neighbour. Let’s take a look!

In general, if the fence is in your boundary then you’re allowed to build a 2-metre high brick or wooden fence or wall. However, this may differ depending on your location in the UK. As a result, you may want to reach out to your municipality’s building department in order to determine what these rules and limitations are in your area. In the events whereby there are no such restrictions but you’re still concerned, you can try informing your neighbour what your concerns are. However, if they’re not receptive there are some steps you can take to ensure your plans go as smoothly as possible. These steps include the following:

• Ensure to leave sufficient space for both the posts and footings
• Stagger your fence posts in order to make sure you’re not digging your neighbour’s
• Consider using concrete posts as they’re much stronger and will last a lot longer
• Use kickers or plinths for raised gardens and flower beds
• Make use of concrete plinths as they won’t rot over time like a wooden fence.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.