Find a Shop Fitter you can trust in Sturminster Newton.

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.

Whether you think resin bound driveways are expensive or not will depend on your perception. While resin bound driveways are the most expensive up front, they should last much longer than other types of driveway. You should expect a resin bound driveway to last at least 25 years, if not longer, while a concrete or asphalt driveway may last between 15-20 years. A pattern imprinted driveway may last even less time due to the maintenance required to keep them looking pristine.

It’s also worth considering that resin bound driveways are good permeable surfaces, so will drain well and keep water from pooling around your property. This will keep your property maintenance costs down, since pooling water or flooding around your home could cause damp in your walls which is a very expensive problem to fix.

Resin bound driveways are by far the most attractive type of driveway to have. There are no loose stones to sweep up, no weeds to pull out from the gaps, and there’s no extensive power washing required to keep them looking good. If you want a driveway that gives your home true kerb appeal and you value your time, resin bound driveways don’t seem that expensive.

The other factor that can make resin bonded driveways less expensive is that sometimes you can lay them on top of the existing surface. For example, if you already have a concrete or asphalt driveway that is in good condition with no large cracks, a driveway contractor may be able to lay the resin and aggregate mix straight over the top, which will cost much less money than if you have to dig up the existing driveway and start from scratch.

A terrible day would be walking into your home to discover your boiler is broken - nobody prays for that and even more so, when you’re fully aware a broken boiler can be one of the most expensive things to repair. However, when this occurs, a boiler plan is ready to help cover the repair cost - and that’s only if you’ve gotten one. Generally, cover plans feature only a monthly price which is quite affordable when compared to paying a huge lump sum at once. Furthermore, depending on your cover level, you may not be required to incur call out charges or any other expensive services rendered. And in the event whereby your boiler can’t be repaired, there’ll be plans in place to get a replacement unit. As a result, getting a boiler cover is a great way to give yourself a peace of mind and see to it that you’re not left in the cold when the worse happens.

So the answer to whether or not you should get a boiler cover is totally a positive one. The purchase of a new heating system can be quite costly, but it would even be costlier when you have to repair it ceaselessly throughout it’s service years. With several modern combi units being a complicated heating system to repair, getting a cover plan with unlimited call outs, zero excess as well as cover parts and labour would be a truly wise decision.

In addition, an annual service of your heating system is required by manufacturers in order to make the warranty valid. Therefore, just a basic service plan is very crucial if you do not buy the idea of having to fork out at least £70 for each service.

First and foremost, HETAS simply refers to Heating Equipment and Testing Approval Scheme. Several solid fuel and wood biomass appliances and systems’ installations are subject to the specified rules of Building Regulations while also being notifiable to the Local Authority in your area by the law. HETAS registered installers are able to self-certificate projects carried out by themselves which helps to prevent the need for the expensive and time consuming Building Notice application which would be made to the local Building Control Department.

Therefore, there are a number of benefits that you stand to derive by hiring a HETAS engineer to fit your solid fuel boilers. Now let’s have a look!

✓ HETAS is the only competent engineers scheme that specializes in solid fuel as well as wood biomass.

✓ All registered installers by HETAS are properly trained and assessed to be competent to carry out a great job.

✓ HETAS offers both technical and regulatory support to registrants.

✓ The HETAS scheme covers all the scope of work that an installer should be able to carry out such as dry appliances, solid mineral, wood biomass, appliances with boilers, wood, hot water and heating systems as well as re liningof chimneys.

✓ HETAS also publishes and makes available the list of approved appliances, fuels and equipment in order to help consumer, installers as well as the specifiers in selecting an installation that perfectly suits the consumers’ needs, while also complying the the provisions of the Building regulations and safety standards.

✓ HETAS also makes available the lists of installers, flue professionals, chimney sweeps as well as maintenance companies to help you to safely maintain your installation into the future.

✓ HETAS also helps consumers in resolving any problems of complaints in such a way to promote a fair and equitable result.

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.

How To Clean Roof Lights

If you have existing roof lights or perhaps you’re about to have them installed, it’s important to know just how to have them cleaned, even if you wouldn’t be doing it yourself. Generally, glass roof lights fitted in flat roof applications are more likely to be a major victim of staining and discolouration by several elements like rainwater, bird droppings, vehicle exhaust pollutants as well as tree sap. Therefore, just like any other parts of your home, periodic inspection of the units as well as regular cleaning is highly advised to help maintain their top performance for a lengthy period of time.

Firstly, when installing the roof lights, it’ll be helpful if its fitted at the right pitch so as to help keep the exterior clean as it enables the elements such as rainwater to run off the surface naturally. Cleaning roof lights involves working at height which can be very dangerous. Therefore, if you lack the skill and confidence to pull this off, it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, we aim to give you a good insight into how the roof light cleaning process works. Let’s have a look!

Rooflight Interior Cleaning

✓ Spread plastic under the roof light to catch dirt and spills

✓ Dust to wipe clear all loose dirt and cobwebs.

✓ Use a squeegee with a warm soapy water or any other glass cleaning product to clean the glass ( steer clear of any harsh chemicals or abrasive cleaners)

✓ Dry the roof light with a soft and lint-free cloth.

Rooflight Exterior Cleaning

✓ Access the roof safely with a specialist ladder

✓ Put mild detergent into a bucket and carry up to the roof before filling with warm water from a hosepipe

✓ Use the soapy water and a non-abrasive cloth or squeegee to clean the roof light, its surroundings as well as fixings.

Unlike several other complex multi choice products, composite door prices are no great mystery. However, it all depends on your personal preferences as well as your budget. There are a variety of customization options and extras, so you can easily select one that’s unique to your home. Composite doors offer you more colours, more styles, a greater choice of accessories as well as more glazing options. With the availability of a plethora of options in the market, it’s very hard to provide a precise price for a composite door as all the options play a significant role in the price structure.

• The Door’s Quality

Composite doors commonly comes with either a CFC-free insulating polyurethane (PU) foam or a laminated hardwood core. The price to be paid will depend on the quality of the composite with the laminated hardwood core being of more quality and ultimately, more expensive.

• Glazing Options

Between a coloured leaded glass double panel and a clear double-glazed panel there’s a huge price difference. And within these two extremes, there are also many other variables.

• Accessories

There are a world of choices when it comes to accessories in terms of the handle styles, letterplates, knockers and more. All playing a role in the price of the composite door.

• Locking System

A common feature of several composite doors is the multi point locking systems. However, the price, choice and security of the lock cylinder can be hugely different which also play a part in the price of the composite door.

• Location

Your geographical location plays an even more important part when you’re having your door installed. For instance, delivery in certain areas in the UK or finding tradesmen comes at a premium which is also shown in the price.

How To Tile Conservatory Roof

If you’re thinking about replacing your old conservatory roof with a tiled one, you’d probably want to know how you can go about it. Tiling of a conservatory roof comes with a plethora of benefits with the most significant one being a much improved insulation which helps you save money on heating bills. This activity is also, however, a task that is best done by a professional. It requires working at height which can be very dangerous and also demands a particular set of skills as well as confidence to make the project a safe and successful one. In other words, if you lack any of the aforementioned attributes, then we’d strongly recommend that you call in a reliable professional who can guarantee the best results for help. In this article, we’ll walk you through the conservatory roof tiling process.

✓ Remove the existing roof. As you would have guessed, the first step is to remove the old existing roof and dispose off in an environmental friendly way.

✓ Glass Reinforced Plastic (GRP) rafters are fitted so as to develop the structural frame for the new solid roof.

✓ Waterproofing. The next step is to add 100% waterproof sheets under the GRP rafters.

✓ Insulation. Once the waterproof sheets have been installed, it’s then time to fit the insulation boards making sure that there’s a 15mm gap between the boards and the waterproof sheets.

✓ Outer sheets. To minimize the number of roofing bars and increase the conservatory’s efficiency, you’ll have to include the outer sheets at this stage.

✓ Tiling. This is the final step in the process. Add the tiles to the conservatory roof and make sure that they’re firmly secured. This wouldn’t take forever as most conservatories are not that big in size.