Find a Shop Fitter you can trust in Gretna.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

• The rules only apply to houses – flats and maisonettes are not included
• Only 50% of the area of land around the original house can be covered by extensions, including conservatories, and other buildings
• You mustn’t build the conservatory higher than the highest part of the original roof
• Where the wooden conservatory comes within 2 metres of the boundary, the height at the eaves can’t exceed 3 metres
• A rear wooden conservatory can’t extend beyond the rear wall of the original house by more than 4 metres if it’s a detached house, or more than 3 metres for any other type of house
• For side extensions, for example a lean-to wooden conservatory, it can’t exceed 4 metres in height and can only be up to half the width of the original house

Leaves, twigs and moss all have one thing in common which often annoys home and property owners - they are the three main materials that negatively impacts the proper functioning of a roof guttering system. The major cause of water drainage problems for most homes and buildings are these organic materials. Wondering how some leaves and few twigs can cause such a big problem? Over time there’ll be a gradual build up of the natural debris in your gutter system which starts to rot and turn  to a thick and muddy goo which obstructs the flow of water in your drainage. As a result, there’s the need to make sure that your gutters are thoroughly cleaned at least twice annually in order to prevent bigger issues that can be caused by the blockage of a drainage system.

So if you’re considering getting your gutters cleaned by a professional, you’d probably be interested in know just how it’s going to cost. Well, there’s not straightforward and simple answer to this question as there are a number of factors that contributes to the final cleaning cost of your gutters.

In general, in the UK, the average cost for cleaning of gutter is usually around £18 to about £25 per hour. However, you can also be quoted a day rate which is usually ranging between £150 to £200 per day.

The factors that can affect gutter cleaning price includes the type of your property (such as a terraced, end of terraced, detached and semi detached homes) which possesses a varying gutter cleaning price largely due to their size differences, the height of the building ( if you require the service for a property located on the second floor of a building, this would be a bit higher than if it were to be on the ground floor) as well as additional requests.

As with every home development project, a home makeover comes with heaps of preparation and, hard work, but it is a remarkable way to breathe new life into an old home.

RESEARCH PERIOD FEATURES AND SAFEGUARD THEM

Get to know your household better, the time it was constructed in, and the kind of individuals who would have lived there. The greatest tactic is to repair current structures, make the house dry and safe.

CHECK FOR RENOVATION RESTRICTIONS BEFORE YOU START

There are certain restrictions that don’t allow you to remodel your house after a certain extent, it should be made clear to you when you purchase the property but if you are unsure about the regulations you should check them up, as it is a criminal offence to carry out unauthorised work to a listed home. Restrictions in Conservation Areas generally affect only the exterior of the property as the intention is to ‘preserve or enhance the character or appearance’ of an area, but the right to develop your house will be affected. This means the kind of work that you could have easily completed in a different location may need certain planning and even permissions to complete in your area.

CREATE A DESIGN FOR YOUR HOUSE RENOVATION

It is very important that you take your time to perfect the design. This will help to ensure that the finished work is in tune with your needs. You will also need to figure it out how the changes might play with the original building.

FIND THE BEST CONTRACTORS FOR YOUR RENOVATION

If you are planning on managing the renovation project yourself, it is advisable to ask from friends or family who have renovated their house before and have undergone a similar experience. They can help you find the right architect and builder. Or else, you can always opt for a project manager.

Due to its numerous advantages, bathroom floor tiles are a popular choice for homeowners across the country. Not only are they durable and good looking, but they’re also resistant to both moisture and stains. Hence, they’re very easy to maintain and with skill, confidence and patience, can also be relatively easy to install especially when compared to wall tiles which is a vertical surface.

Fitting bathroom floor tiles requires a lot of planning as it can be easy to make costly errors here and there. Generally, this task shouldn’t pose any serious difficulty for a confident and patient DIYer. However, if you lack these attributes, then it’s advisable to call in a professional who can guarantee the best results for help. In this article, we’ll take you through the bathroom floor tiles installation process. Let’s get started!

• Make Sure You Have A Levelled Subfloor

✓ Your subfloor’s stability is crucial for the success of your tile laying.

✓ Once done, then you can start planning how to level the floor.

✓ Identify the highest point of your floor and place a really long level to determine the dip and hump spots.

✓ Fill in the identified low spots with mortar.

• Cut The Tiles

✓ Using a wet saw with a diamond blade and pump, cut through the tiles to get the appropriate shape.

• Choose The Appropriate Adhesive

✓ To best adhesive is probably the one written on the label and suggested by the manufacturer.

✓ If uncertain, you can make use of a modified mortar

• Prepare The Area

✓ Using the prepared mixture of your mortar, prime the surface by spreading it on the floor with the trowel’s flat side.

✓ Once done, you can add more mortar with the ridges of the trowel.

• Space The Tiles

✓ Tile spacement depends largely on the surrounding walls. Straight walls equal straight tiles, if not your judge would be required to ensure a great outcome.

✓ If the wall is straight, make a space of about an eighth of an inch. The bigger spacing, the higher the possibility for the grout to become visibly discoloured.

• Use The Right Grout

✓ With sanded and unsanded grouts having a variety of colours, choosing the ideal grout can a tricky affair.

✓ The size of the spaces play a huge role in determining the best choice.

✓ Use a sanded grout if the spacing is an eighth of an inch or more. However if less, make use of the unsanded grout.

This will vary depending on the type of pest. For insects, an insecticide spray or powder will usually be applied to the area. For other pests such as rodents, poison and traps will generally be used. Birds and larger mammals are often caught and released back into the wild.

Structural Engineers are experts in the structure of establishments (structures, wall structures as well as roofs). They give solutions whereby they will evaluate issues with existing establishments as well as additionally aid with structural design and computations for changes. They can additionally supply solutions in regard to the design of brand-new premises as well as planning permission applications.

When home or property owners decide to plant a Leylandii, they mostly think about how great it is as a hedging and screening plant and forgetting it also require a regular maintenance to keep in good shape. One thing about Leylandii are they do not re grow if you happen to cut back into the old wood. Once it turns brown, it will remain like that with no possible solutions to remedy the situation as they have little to no ability to regrow from the old wood.

In order to maintain your Leylandii hedge in good shape and order, that’s not too wide or too tall, then it’s recommended that it should be trimmed at least once a year. By doing this, you’re more likely to cut only into the new green growth which will enable the hedging plant look great and green with no brown patches. So when is the best time to prune a Leylandii hedge plant in a year?

Generally, it’s advisable to cut back mature or overgrown Leylandii hedges in the UK about two to three cuts between the months of April and August. By this time, your hedge plant will already be well established and ready for some maintenance and care. However, if there’s a chance that you might not be able to prune it on a yearly basis, the we’d suggest you get a slower growing alternative instead. Some of the alternatives which are slower growing and unlike Leylandii, can regenerate when cut back into the old wood are several types of Thuja as well as English Yew.

Below are some guidelines you can follow when trimming your Leylandii hedge:

• Do not cut Leylandii hedges during very forsty or hot weather.

• Do not cut the hedges during wet conditions to allow the cut dry and heal quickly.

• Make use of sharp tools.

• Cut on a cool and breezy day.