Find a Shop Fitter you can trust in Clydebank.

If you live in an average home with an average amount of guttering and you’re used to a bit of DIY, it’s relatively easy to replace gutters. But if you have a home that’s more than two-storey or you have guttering that’s more complicated, it’s best left to the professionals.

Lots of homes these days have uPVC guttering. uPVC is a hard-wearing plastic that will last a long time without much maintenance except your usual gutter clearing. It’s relatively light, so lots of people think it’s easy to replace uPVC gutters. If you live in a bungalow, you may be able to just use a ladder to take down your old guttering and replace it with new uPVC gutters, but if you live in a two-storey home it can be a bit more complicated. If you do attempt to replace your gutters yourself, make sure you’ve got a sturdy ladder that will comfortably reach the right height, and never rest it on the fascia or the guttering itself.

If you have cast iron or copper guttering, this is much heavier and bulkier than uPVC. Certainly don’t try to replace these on your own – make sure you have another competent DIYer to help you. Reputable roofline specialists will use scaffold towers to make it easier to handle heavy gutters and they will always work in pairs on this type of guttering, so make sure you have the right tools and equipment to work with.

Just because it’s easy to replace gutters, it doesn’t mean you should. It’s better to ask a reliable roofline company to help you, since they have the skills to fit guttering properly and have experience with working at height.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Artex is a water based surface coating which is used to decorate both ceilings and walls with a textured finish. Back in the 1970’s, artex happens to be very popular when the swirling or spiky effects it creates  were considered to be the best of fashion when it comes to interior designs. However, in today’s world, an artex ceiling is not only considered outdated but also a pain to clean and repair.

If you have an artex ceiling in your residential property and looking for a way to get it off, then you’ve come to the right place. In this post, we’re going to show you how its done without much stress.

To get started you’d need to get the following tools and material which includes: safety goggles, dust mask and rubber gloves, plastic sheeting, canvas drop cloth ( carpet) or rosin paper (hard floor) and step ladder

Prepare the room. Start this by moving all furniture out of the room or stack the furniture at the centre of the room and cover using plastic sheets. Once done, cover all non-removable items with plastic sheets and lay down a canvas drop cloth for carpet floors and rosin paper for hard floors

• Put on your safety gear
• Use a utility knife or joint knife to slowly chip away at the texture and create a smooth surface.
• Mix joint compound in a bucket as per the instructions on the package
• Skim the surface with a thin layer of joint compound to smooth it out using a taping knife, then leave to dry overnight before you proceed
• Lightly sand the surface smooth with the help of a 220-grit sanding block
• Use a damp cloth to wipe the surface clean prior to painting.

A thermostatic shower is simply a shower that only needs to be set at a given temperature and it automatically maintains this set water temperature all by itself. Typically, this type of shower functions with the three primary types of water system available in the UK. Thermostatic showers are very popular in residential buildings featuring both mains-fed hot water systems as well as combi-boiler systems due to the fact that they’re both renowned for the ease through which the flow of water can be affected by the actions of other individuals. In some events, this can mean the action of individuals in separate properties. As a result, gravity-fed water systems are usually more reliable, but even at that, thermostatic shower valves are mostly seen as an additional safety feature that’s quite useful should it be required. So how exactly does the thermostatic shower work?

A thermostatic shower makes use of a thermostatic valve to mix both the cold and hot feeds in the right proportion prior to channeling the water via the showerhead. As a result of the link that exists between water pressure and water temperature, this is able to maintain a steady flow. What’s more? Contemporary thermostatic showers can also shut down by itself if it observes that the supply of cold water has reduced to a level that’s considered to be unsafe which ultimately prevents scalding. What thermostatic showers simply does is to store hot water from the mains and then mix it with the right quantity of cold water in order to generate the desired temperature. They’re unlike electric showers which collect cold water from the mains and heat it up to the set temperature.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

You can only repair blown double glazed windows in the sense that you can replace the sealed unit (the glass part of the window) instead of having to replace the entire window.

When a double glazed window is blown, it means that the seal around the window has failed and is now letting air in and out. Often the first sign that the sealed unit has blown is condensation on the inside of the window, which is annoying since there’s no way to get rid of it! When your sealed unit has blown, you’ll be losing heat out of the window, meaning you could be spending more on your energy bills.

As a temporary fix, you could see if you can buy a misting repair kit online, but the condensation will eventually occur again as the air gets in. The best thing to do is ask a window installer or glazier to replace the sealed unit for you.

It's simple to replace the glass in a window – the specialist will remove the beading around the window, remove the blown glass from your window frame and set it to one side. They will then clean up around the frame before adding spacers in, then fitting the new sealed unit into the frame. They’ll make sure it’s a snug fit before replacing the beading back around the window to secure it.

There's no reason to put off repairing a blown double glazed window since the cost is generally much less than replacing the entire thing. A sealed unit with installation costs an average of £100, whereas a completely new window will cost around £400. You’ll soon notice that it’s less draughty and will be able see out of your window once you’ve had the blown glass replaced.

Fitted wardrobes are the best choice of wardrobe for most households and they’re a popular option for several homeowners for a good reason. Not only are they able to efficiently maximize your space and fit into any space no matter how awkward, but they can also be customized to fit your personal needs to feature custom lighting and many more. So if you’re planning to have one fitted but on a tight budget, you’d probably be wondering how you can install a fitted wardrobe in an alcove by yourself. This is a relatively easy task if you’re attentive to the details, however, if you’re not confident enough to pull this off, we’d advise that you get in touch with a professional who can guarantee the best results for help.

To construct a fitted wardrobe in an alcove, simply follow these steps:

✓ Take a measurement of the available space including the length, breadth and width.

✓ Sketch out what you want the wardrobe to look like while also staying within the measurements. Here, you’ll have to be particular about everything like the drawers, shelves etc.

✓ Build the frames upon which every other construction would be made.

✓ Attach the frames to the wall and floor. Make use of a hammer drill with a masonry bit to drill the holes if its a concrete floor.

✓ At this stage, you’ll have to start building your shelves in accordance to the number you’ll need.

✓ Based on the design in step 2 above, you’ll have to add the door at this stage. This is however optional as some homeowners prefer door-less wardrobes.

✓ The final step is to paint the the finished wardrobe to your taste with your choice of colour.

A barn conversion is where an agricultural building is altered to serve a different purpose. Lots of barns conversion projects involve converting an old barn into one or more homes. However, barns can also be converted into other types of commercial building, like offices.