Find a Shop Fitter you can trust in Anstruther.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

How To Replace Roof Tiles

If your roof tiles is cracked, missing or damaged in one form or the other, you may want to read up to see if the replacement is something you can do by yourself. The answer is yes, roof tiles replacement can be done as a DIY project especially if you’re an experienced DIYer or confident enough to tackle the project. However, if you lack the confidence needed to take on this task, then we’d strongly recommend you get in touch with a professional roofer who can guarantee the best results for help. In this article, we’ll show you how you can replace your roof tiles with relative ease. Let’s take a look!

✓ As you would have rightly guessed, the first step to replacing your roof tiles is to remove the existing damaged roof tile to create space for the new tile. In the event whereby the roof tile is nailed to down, you will have to pry the nails off before proceeding with the broken tile removal.

✓ Once the damaged tile has been removed, the next step is to replace the roof tile as there’ll now be a gap in the roofing area. Simply position the new tile rightly into the space that was formerly filled by the old damaged tile.

✓ After successfully placing the new tiles in spot of the removed tile, you’ll now have to replace the overlapping tiles to their correct position to secure them. To this with a hammer to lift the overlapping tiles a little bit, so you can pull them back into the appropriate place.

✓ This final step is not a necessary one. However, if you’d like to secure your roof tiles further, you can simply nail it into place with a hammer.

How Long Does A Locksmith Take?

It’s usually a surprising experience when a security issue that you might have thought is not resolvable or nearly impossible to overcome, took an expert locksmith just a couple of minutes to fix. This is not magic or some voodoo, it’s just a learnt skill being perfectly applied by an experienced and well versed locksmith. In this article, you’ll get to know what to expect when you call on a locksmithing professional for help with a security issue.

To determine the period of time a locksmith will take to complete his services, two factors are to be considered - the estimated arrival time as well as the service providing time.

Generally, if you call on a local locksmithing company, you should expect the locksmith to arrive within 15 to 30 minutes to your location. However, this might be shorter or longer if you put into account some influences such as the distance involved and traffic. Some companies can show up faster but charge an extra fee to it, while others will need more time to show up but offers a cheaper service. Usually, locksmithing companies will publish information about the estimated time of the arrival of their technicians on their websites. If you don’t find any, you might want to consider another company with one as this is a red flag.

The second factor which is the service providing time which depends on many influences including the type of lock and key in question. Therefore, it’s impossible to give a precise answer. However in general, a professional locksmith would not usually take more than an hour and half to create a new key for a car or house, or more than 10 minutes to unlock a house or car. Whereas replacement of a lock can take within the range 10 minutes to 40 minutes depending on the complexity of the lock.

Since it’s very common to find heated floors in the bathroom, it becomes very understandable that most home and property owners are fitting a radiant floor heating system under tile flooring. If you’re thinking about how you can fit heat under tile floor, then you’ve come to the right place. However, if you lack enough confidence to pull this off, then we’d advise you get in touch with a professional who can guarantee the best results for help. In this guide, we’d be considering how heating products are fitted under the most commonly heated flooring material which is tile. Let’s take a look!

1. Take a measurement of the room you wish to heat. When taking this measurement, you should leave out permanent fixtures such as tubs, toilets, floor vents and more. This information will be used to create a project sketch which includes the room dimensions
2. Test your electric floor heating rolls. To make sure that your floor heating rolls are in perfect working condition, you should use a digital ohmmeter to test it.
3. Inspect the subfloor. Clear the surface of any nails or other sharp objects which could cause damage to the heating element.
4. Install the flex roll. Simply roll out your flex roll till it gets to the opposite side of the room. Once done, you can then cut the mesh and turn 180 degrees to continue fitting in the other direction.
5. Place the sensor. If you happen to possess a floor heating thermostat that enables a floor sensor, ensure to position the sensor near the thermostat’s location and exactly between two cables, then use hot glue or weave into mesh to secure it.
6. Connect the thermostat. We’d advise you get in touch with a professional to have this done.
7. Install the tile.

Rendering is an external wall’s plastered finish which provides a smooth finish while also protecting the brickwork from the elements like rain, snow and the likes. The traditional rendering is normally applied in two or three coats which enables it to be more resistant to surface cracks. In modern times, the finishes are largely different from the grey pebble dash of post war housing. Today, we now have a plethora of specialist products to pick from such as through-coloured silicone renders as well as one coat renders. The types of renders include the following:

✓ Cement renders. These are the common option that are usually mixed on site and used in a number of applications, then painted when dried. There’s a need to paint this type of render regularly to keep them looking great.

✓ Polymer renders. These are pre mixed and mostly pre coloured (usually with through colouring).

✓ Through-coloured products. These rendered do not need to be painted as the pigment is already added in the manufacturing process to colour the whole render.

✓ Lime renders. These are superior to cement as they’re less likely to trap moisture in the brickwork and also more good looking. However, they’re generally more costly and more difficult to apply.

Overall, rendering on a house provides several benefits. Not only is it able to protect your brickwork against the elements like the rain and wind, but it can also make the building more efficient. Being fully aware that about 30 percent of the energy used in heating a home is lost via the external walls, making use of a product such as acrylic insulated render is a smart approach to improve your home’s energy efficiency without affecting your interior living space.

If you’re looking at the possibility of installing a satellite dish on your chimney, then you’ve come to the right place! First and foremost, it should be noted that chimney mounts are mostly incorporated for individuals who desires the installation of an antenna at the highest point of their roofs without having to drill holes in the roof. This is quite popular as they’re able to ensure an easy installation and also works incredibly well for several antennas. What about satellite dish? Can it also be mounted on a chimney? Let’s take a look!

The short and simple answer to this question is yes, a satellite dish can be installed on a chimney. However, it must be said that this installation is not advisable. Unlike antennas, satellite dishes are aimed much more precisely. While antennas can be positioned as far as 15 degrees off the main aim before the reception is affected, satellite dishes, on the other hand, need to be positioned about one half of one degree in order to allow for a good operation. This is mainly because the broadcast tower you’re aiming your antenna at is, at most, 75 miles away compared to satellite dishes which are aimed at broadcast towers which are at least 22,000 miles away and that’s even if you happen to be directly under one.

Installing a satellite dish on a chimney will make it difficult for you to get it secure enough to have it properly aimed. This isn’t to say it won’t work at first, but most times, winds will probably drive the satellite dish off the target in little time.

If you get the right size boiler for your business and you get it serviced regularly, your boiler could last up to 15 years. It may even last longer than this, but you’ll find that your boiler begins to become less efficient as it gets older. Also, as technology improves, a boiler older than 15 years may not be the most efficient one on the market.

Many types of loft are suitable for a loft conversion. In general, you will need at least 2.3 metres of headroom in your existing loft. This is to make sure there is enough headroom after the conversion. Speak to a conversion specialist about the probability and possibility of doing this in your house.