Find a Shop Fitter you can trust in Aberffraw.

If you’re going through new constructions or renovations and looking to change your old front door and install a brand new composite door, then you’re at the right place. Composite door fitting can be a DIY project but it’s essential to have the necessary training and experience before commencement. If not, we’d recommend you hire the services of a reliable professional to guarantee the best results and save yourself some time and money.Here, we’ll give a good insight into the composite door fitting process.

To get started, here are some of the tools that may be required - tape measure, hammer, stanley knife, crowbar, chisel, saw. Silicone sealant gun, spirit levels, electric drill ( including the hammer section), rubber mallet and 6mm socket spanner.

lPreparation

• Remove the existing door by rounding up the door frame firstly with a knife to reduce the possible damage to the wall.

• Cut through the door jambs.

• Remove each in two separate sections.

• Ensure the opening is level without any screws, mastic and filler.

lAlign Your Composite Door

• Ensure the sill of the door is level and flat.

• Make sure the frame is square and plumb in both planes.

• Bridge the cavity of the wall and cover the DPC

• Ensure that the frame is square. If not, your composite door won’t function as it should.

lInstall Your Composite Door

• Place the door in the frame.

• Hold the frame firmly in position with wedge packers

• Make sure the packers are positioned close to where the fixing will be placed.

• Make sure the jams are square and plumb in all planes by using a long spirit level.

• Secure the frame to the brickwork with the use of a drill.

• Place the fixings at the top and bottom of each hinge as well as each of the lock keep.

• Top fixings should be fitted 150mm and 250mm from each corner.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

When it comes to air conditioning, there’s nothing like a one-size-fits-all approach as different buildings have different needs. As a result, there are various types of air conditioners to address unique building requirements. Having a full grasp of the differences between a commercial air conditioner and a residential air conditioner can go a long way to help you in choosing the most appropriate system for your building to ensure all occupants can enjoy the high air quality at the perfect temperature.

Now, while both commercial and residential HVAC systems serve the same purpose of heating, cooling as well as ventilating, they are largely varied in terms of the parts and mechanisms. This is due to the fact that tackling the need for comfort in a home or residential space is very different when compared to a work environment.

First and foremost, there’s usually a distinct physical difference between commercial and residential air conditioners. The residential ones are usually central systems which are linked to a series of ducts, with the evaporator and condenser in separate areas of the property. On the other hand, the commercial systems normally combines both heating and cooling units in one rooftop package that prevents the noise it produces from disturbing the work of the occupants. Having the package on the roof also goes a long way to help the companies free up some physical space.

The main difference between a commercial air conditioner and a residential air conditioner, however, is the amount of power which the system consumes to cool off a space. This is partly because a work environment usually takes up more space than residential environments. As a result, heating and cooling systems that are intended for use in commercial spaces are usually built to be a lot more powerful.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

You don’t have to, especially if you’re on a budget. If you’re only replacing some, it’s a good idea to get all the windows on one side of your property replaced at the same time, so they all look the same. Be aware, obviously, huge savings could be had by having a number of windows replaced at the same time.

If you’re thinking about making improvements to your home, it’s only reasonable to become familiar with the ins and outs of the requirements to make the project a success. Not just the cost involved to complete the project, but also the duration it’ll take to complete the job and lots more. When it comes to the installation of wooden flooring, there’s a need to find out whether or not an underlay is required for the task. In this article, we’re going to consider this in order to ensure that you’re on the right track. Let’s take a look!

First and foremost, underlays are common with carpets as they allow for an even surface with no lumps and bumps. It also provides a deeper barrier between the carpet and the floor as carpets, themselves, aren’t particularly thick enough to provide adequate comfort when walking on them. Underlay also helps improve insulation which in turn, helps cut down your energy bill. So, are underlays also needed with wooden flooring?

In general, wooden flooring does not really need an underlay. This is due to the fact that they’re perfectly comfortable to walk on without the need to add an extra padding underneath. However, the subfloor will have to be made prior to the installation, as a result, an underlay is needed at all there. With that in mind, it’s highly recommended to make use of an underlay when installing a boarded floor to a wooden subfloor mainly due to the fact that it’s able to provide a much-improved insulation. When it comes to wooden flooring, it’s always best to go for quality rather than looking for ways to cut corners. If you’re able to go for the best project with professional installation and little extras like undelay, you’d notice and enjoy the long lasting nature of your wooden flooring immediately after installation.

Chances are at some point you’d probably given a though about how steps would fit in perfectly in your garden, except of course, your yard and garden is flat. Adding steps and gardens makes it a lot easier to get around your yard while also enhancing its curb appeal. In order to avoid the cost of hiring a professional to get the task done, you might be tempted to make it a DIY task. However, if you lack the required skill and confidence to pull this off, we’d strongly recommend you call in a professional so as to avoid costly errors. In this post, we’re going to take you through the garden steps building process. Let’s take a look!

1. Measure the vertical height of the slope by marking it with two parallel lines. Once done, proceed by connecting a string line to the slope’s top and hold it in a horizontal way, take a measurement of the flight’s length and breadth. Divide the measurement by 200mm to get the number of steps that’ll be required. Then proceed to divide the number by the height to identify the depth of each step.
2. Working downwards from the flight’s top, dig the step shapes and also dig a shallow trench and install a concrete foundation.
3. Enable the foundation to harden by leaving it for about 48 hours, then install two courses of bricks on the concrete strip and use gravel to backfill.
4. With the help of a trowel, apply mortar to the top of the brickwork. Place the first slab on the mortar bed and press down. Then, make use of a spirit level to make sure that the steps are level.
5. On the back edge of the first tread, you should proceed to build the second rise, backfill and install the slab to form the second tread – just like the previous step. Repeat this process until you’ve gotten to the top of the flight.