Find a Shop Fitter you can trust in Holyhead.

In most areas, you will not need planning permission. However, if the property is listed or in a conservation area, you will need listed building consent or planning permission to paint the exterior. A surveyor or architect's advice will be invaluable as they can help with this process.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

A combination boiler, also referred to as a “combi boiler, delivers both domestic hot water and space heating in a single package so as to save space, and in a lot of cases, money. These great features makes the appliance a very popular choice in UK homes and in fact, it represents more than 50 percent of all new boilers fitted in the UK on a yearly basis.

Most modern and high efficiency combi boilers are usually stainless steel condensing boilers which normally features an in-built secondary heat exchanger to deliver domestic hot water to a home or property. What’s more? When it comes to the heating season or the cold months, the combi boiler will operated as required to heat a structure and offer hot water for showers, sinks as well as other hot water appliances around the house. And when it gets to the warm season or summer months, the combi boiler will only work when there’s a need for domestic hot water which also helps you save more money.

Combi boilers are able to provide domestic hot water in such a way that’s energy efficient due to two primary reasons - the combi units possess a very high operating efficiency and also have a low internal water volume. As a result, in during the hot summer when space heating is not required, you’ll only have to pay to heat up the hot water that you really need and not an entire tank.

Combi boilers also have the following benefits:

✓ Lower costs. Due to the combined nature of the boiler and the lack of tank in the roof space, the installation time and costs are at a minimum.

✓ Saves space in your home as it effectively combines a central heating boiler with a water heater into one unit.

As the heat start to come up especially during the summer months, the swelter will mercifully be kept in check by air conditioning. The technology has made a significant impact on modern life and it can now be considered a norm for all new and modern homes. So if you’re also planning to fit new HVAC air conditioning systems in your home or property, you may also be interested in knowing exactly how it works. In this article, we aim to provide you with an in depth insight into how air conditioning operates. Now let’s take a closer look at the process!

✓ A grille at the bottom of the machine absorbs warm air from the room

✓ The warm air is transmitted over some chiller pipes through which a coolant fluid is circulating. Working in a similar fashion as the chiller cabinet in a refrigerator, this part cools down the transmitted warm air and any excess moisture is duly removed by a dehumidifier.

✓ The air is then transmitted over a heating element which is quite similar to the one present in a fan heater. On a cold day, this part of the unit can be turned up in order to allow the HVAC works as heater.

✓ A fan which is positioned at the top blows the air back through another grilled into the room.

✓ Coolant flows through the the chiller pipes. In the process, it carries heat from the air blowing past the pipes and then it evaporates - converting the cool liquid into a hotter gas. This heat is then transported to the outside of the building from inside the room.

✓ With time, the heat inside the building slowly blows away into the outside air.

Every year, various parts of your roof may need to be changed at one point or the other. Due to the fact that this event can occur at any time in a year, there’s the need to be fully ready. When it comes that being ready, you simply can’t overlook the importance of soffit and fascia boards in protecting your roof space and helping it maintain its clean and unique visual appeal. As a result, when your soffit and fascia boards need to be changed, you best do so as quickly as possible.

This task can be completed by anyone with basic DIY knowledge and experience, but if you lack the confidence to pull off then it’ll be advisable to hire a professional who can guarantee the best results for help.

✓ Remove the old existing boards. In order to install the new soffit and fascia boards, you’d have to remove the existing ones first. If necessary, you can make use of a Stanley knife to make the process much easier.

✓ Fixing soffit boards. Several soffit boards are made using uPVC. The boards are to fixed to the underside of your timber rafter ends. Make sure to use timber to close any gaps between soffit boards and also make sure that your soffit boards’ back are resting against the wall’s top.

✓ Fixing fascia boards. Many fascia boards are also made from uPVC and are usually installed in a similar way to soffit boards. Use a minimum of two nails to make sure they’re secure enough to hold weight of any roof tiles and also to prevent any buckling.

✓ Guttering and felt. To start the guttering, you’d have to screw any brackets into the facia board. You can use a spirit levelto make sure the alignment is perfect to enable the floe of water directly through your guttering system. Once done, you should also check for any rotting roof felt at the edges closest to the gutterin. If there is a rot, make use of eaves felt trays and tuck under existing felt and overlap into the guttering

As the heat start to come up especially during the summer months, the swelter will mercifully be kept in check by air conditioning. The technology has made a significant impact on modern life and it can now be considered a norm for all new and modern homes. So if you’re also planning to fit new HVAC air conditioning systems in your home or property, you may also be interested in knowing exactly how it works. In this article, we aim to provide you with an in depth insight into how air conditioning operates. Now let’s take a closer look at the process!

✓ A grille at the bottom of the machine absorbs warm air from the room

✓ The warm air is transmitted over some chiller pipes through which a coolant fluid is circulating. Working in a similar fashion as the chiller cabinet in a refrigerator, this part cools down the transmitted warm air and any excess moisture is duly removed by a dehumidifier.

✓ The air is then transmitted over a heating element which is quite similar to the one present in a fan heater. On a cold day, this part of the unit can be turned up in order to allow the HVAC works as heater.

✓ A fan which is positioned at the top blows the air back through another grilled into the room.

✓ Coolant flows through the the chiller pipes. In the process, it carries heat from the air blowing past the pipes and then it evaporates - converting the cool liquid into a hotter gas. This heat is then transported to the outside of the building from inside the room.

✓ With time, the heat inside the building slowly blows away into the outside air.

Common reasons you may need a structural engineering inspection are

1. Bowing/cracked foundation
2. Settlement or wall cracks
3. To remove a wall in a remodel
4. Add solar panels to a roof
5. Add a second story to a home

Are you planning to remove or renovate your garage? Before proceeding with the intended project, it’s usually essential to firstly determine whether or not your garage contains asbestos. However, asbestos isn’t the easiest material to identify and even more so when you’re unsure of what it looks. The fibres on the other hand are not visible to the eye and can’t be smelt as it’s odourless. In this article, we’ll provide you some helpful tips to spot an asbestos garage roof. Let’s take a closer look!

✓ Figure out when the building was constructed. In the year 1999, a ban was placed on the use of asbestos in the UK, both to manufacture and supply of asbestos materials. As a result, if your garage was built before this period, then it’s very likely that an asbestos containing material was used. It’s also important to note that several garage roofs that contain asbestos are constructed with the help of flat or corrugated sheets of cement.

✓ Check the surface. When cement contains asbestos its usually fairly thin with visible fibres running through it. Also, the surface of the cement will have a texture and also some craters. If you an older cement sheets is incorporated, there’s a high chance that it contains asbestos.

✓ How it’s built. Asbestos materials are usually joined together by aluminium runners and help in position with nails that are blunt-ended. Take a look at the joints, if the sheets inside is held together by wooden or plastic runners then there’s danger.

Finally, roofs made from asbestos cement has a good chance of becoming very brittle.