Find a Shop Fitter you can trust in Southsea.

In some circumstances, you may have to hire different companies for different parts of your garage conversion. But most of the time, garage conversion companies have their own tradespeople or contractors that are qualified to do all the work involved. When you're at the quotation stage, any contractor will advise you of what they are able and not able to cover.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

How Much Does It Cost To Service An Oil Boiler?

With several homes in the UK using gas central heating, about 6 percent of households in the United Kingdom makes use of oil for their heating needs. If you’re one of those homeowners with an oil boiler, then you should know that servicing your oil boiler is a compulsory activity which should be done regularly in order to ensure the safety of your home, boost the efficiency of the boiler while also help you save money as it ensures you do not incur the potentially expensive repairs or even having to purchase a replacement boiler. If you service your oil boiler every year, you can be rest assured that you’ll continue to derive maximum benefits from your prized heating system for a long period of time. So exactly how much will you have to pay to service your oil boiler?

The service cost of an oil boiler is influenced by a wide range of factors which includes the location. However, the average cost of servicing an oil boiler in the UK is between £65 to £90, but depending on the location as well as other influencing factors, this price might be higher or lower.

Due to the higher cost of living and high demands at places such as London and the south east of the UK, you can discover that the cost of servicing your oil boiler can jump to as high as £160 to £190. In other regions, you can also find the oil boiler service cost to be as low as £50 to £60. What’s more? In the same locations, you can also discover varying prices which depends on the available services. Furthermore, in areas where there’s a lower competition from several engineers, the prices may also be higher.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

If you’re planning to construct a kitchen diner extension, to help you set a budget and start planning you must first have a cost estimate that’ll complete the entire project. If not, there’s a probability that you may have to spend more than would have been necessary or probably break the bank to have the project done. In truth, there’s no single and short answer to this question as the cost of a kitchen diner is largely dependent of several variables. In this article, we’re going to give a good insight into kitchen diner extension cost so as to help you make informed decisions moving forward. Let’s take a look!

On the average, a kitchen diner extension will cost within the range of £25,000 to about £45,000, however if you happen to reside in London, you can expect the cost to be a lot more than that - closer to £60,000. And due to the fact that there happens to be a plethora of options out there, any decision to make be it on the size, tradesman, flooring, finishes or type of the kitchen diner extension, will have a considerable impact on the overall cost of the project. For instance, a basic kitchen diner extension cost can be within the range of £12,000 to about £15,000., while a high end kitchen diner extension can reach a whooping price between £80,000 to about £100,000.

The total cost of your kitchen diner project will rely heavily of the size as well as the quality of the finishes. For example, a kitchen diner extension that’s small and basic is likely to cost about £1,300 to £1,500 per square metre. However, if you’re going for higher quality finishes, you can expect to pay within the range of £1,900 to about £3,000 per square metre.

Paving can be used for driveways and is capable of bearing the weight of cars and other vehicles. Ensure that you choose the appropriate type of paving, as some are designed for paths or decorative use. Correct installation is vital as improperly installed paving may move or break under the weight of a car.

How Much Is A Metal Front Door?

If you’re looking to get a front door, one of the things you’d want to consider before you proceed is the price of getting the door. As an exterior door, you’ll need something that’s close against weather as well as intrusion. And that’s exactly where steel comes in! It’s a popular choice for exterior door material due to the numerous qualities it possesses. However, the single and precise cost to get a metal front door can not be provided as it depends on a wide array of factors.

The cost to install an average metal front door will depend on the material and finish grade, structural preparation, size, unique needs, labour rate and lots more. Other things you’d have to put into consideration includes the following:

✓ A project to replace more than 2 doors are more likely to enjoy a unit price or bulk discount.

✓ During inspection to replace the existing door with a metal one, there may be some repair concerns like rot and also a need to adapt the existing door opening structure which will also tell on the price

✓ There may be local or national subsidy for energy efficiency improvements.

✓ Taxes and permit fees may also be applicable.

✓ DIY considerations. This project may be suitable for a DIYer with carpentry skills. So if you wish to carry out the installation by yourself that’ll also help you save some money.

Generally, the cost of a metal front door will range between £100 to about £10,000. However, before you purchase a steel door it’s very important to put into consideration what the door is being used for as well as what you’d prioritize between beauty and security - although, most steel doors can offer both at an affordable price.