Find a Shop Fitter you can trust in Ashford.

Solar PV panels work by converting sunlight into electricity. They’re made up of photovoltaic cells, which take in the sun’s rays and turn it into direct current (DC) electricity. The current is then channelled into an inverter, which converts it to alternating current (AC).

Once converted to AC, the electricity is ready to use. It’s fed through a meter and into your property’s consumer unit, and is automatically used to power appliances and heating systems. Your system will automatically switch between your solar electricity supply and the national grid, and export any solar electricity you don’t use to the national grid.

While many professionals will recommend a pressure washer to clean block paving, it’s possible to clean your paving without one – just scrub the affected areas with a firm bristled brush and use plenty of soap. Then, rinse off the area with clean water.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

Storage space is a major consideration for most home buyers and even more so, when there’s the presence of fitted wardrobes. Fitted wardrobes can be installed in just about any room in the house and even in rather obscure places such as under the stairs, inside a loft, around chimneys as well as into alcoves. As a result, they’re important assets to have as they can go a long way to increase the value of your home or property.

Fitted wardrobes are usually made from various types of woods as well as wood finishes. Typically, they’re installed with either sliding or hinged doors depending on the space as well as the styling you opt for. Fitted wardrobes can be personalized through the addition of elegant features such as custom lighting, mirrors as well as internal extras like pull out shoe racks and pull down hanging rails.

For high end customized fitted wardrobe like Sharps, the best quality, most practical and also robust materials are being incorporated. They make use of the following materials given below:

✓ Fibreboard. This is a modern material that’s used for its ability to produce a smooth routed and detailed design. It’s also very solid and robust which makes it perfect for large furniture pieces as they don’t warp or dent. What’s more? Fibreboards meets the European forestry sustainability standards and it also allows for the board to be profiled with a top notch finish.

✓ Particleboard. This material is used for the parts of the furniture which will normally be cut in your home like facings and side panels. Due to it’s lightweight, they’re very easy to cut and doesn’t produce as much dust as other materials. The material is also a highly controllable contemporary material which can be precisely cut arounf skirting boards, covings as well as period features to ensure a perfect fit.

Home electrics can be extremely dangerous and it’s very unwise to try and carry out repair work or maintenance yourself without the necessary knowledge and skill. Therefore we would always recommend using a Part P registered electrician at all times.

Due to the plethora of benefits ceramic floor tiles are able to provide, there’s little surprise they’re a popular flooring choice amongst homeowners. Not only are they durable and good looking, but they’re also resistant to both moisture and stains. Hence, they’re very easy to maintain and with skill, confidence and patience, can also be relatively easy to install especially when compared to wall tiles which is a vertical surface.

If you’re looking to install ceramic floor tiles by yourself, you’ve come to the right place. This is a task any confident and patient DIYer should be able to do with ease. However if you’re not confident enough to pull this off, it’s advisable to get a professional for help. In this guide, we’ll walk you through the process of fitting ceramic floor tiles.

✓ Prepare the subfloor. This involves making sure the layout is even from side to side on both directions, picking up loose tiles and setting them aside.

✓ Spread a thin set of mortar over a 3x3 foot section at the intersection of the layout lines using a notched trowel.

✓ Start to lay the tiles from the centre point of the two layout lines. Simply set the individual tile into the mortar and tap gently with a rubber mallet. Ensure to use spacers at the corner of each tile to maintain an even grout line between the tiles.

✓ Continue spreading the mortar and complete laying of the tiles

✓ Once all the tiles have been perfectly fitted in the mortar, proceed to mix the grout according to the manufacturer’s instructions and apply it with the use of a rubber grout float.

✓ Wipe clear any excess grout with a grout sponge. Once done, let the grout dry up a bit, then remove the haze that comes up.

If you’re thinking about hiring the services of a quantity surveyor for your next building project, then you might probably want to know how much its going to cost to enable you set a budget and start to plan. However, there’s no single and straightforward answer to this question as the price of a survey is dependent on a wide array of factors. The primary drivers include the scope of the construction, the complexity of the property, the level of skill required to make appropriate assessment of the property as well as the level of liability that will be covered by the quantity surveyor. In a more simpler terms, the cost of a quantity surveyor is determined by the size, age, condition, complexity and to some extent agreed purchase price.

Generally, most quantity surveyors are charged out at a rate of £100 per hour. And as a result, the price of a quantity survey is related to the number of hours that’s going to take to make an in depth assessment of the property. Typically, several quantity surveys will take up to half a day on site with a further half going to the production of the survey report. Consequently, it would be totally fair to say that a quantity survey would cost you anywhere within the range of £600 to £800 plus VAT. For a less detailed and simpler survey such as RICS Homebuyers Report and Valuation, you can expect to use only a couple of hours on site which will also be topped by a few hours of work in the report production. As a result, the normal cost of a Homebuyer survey would be between the range of £400 to £500 plus VAT. However, you should take note that the prices can vary on a geographical basis.