Find a Shop Fitter you can trust in Motherwell.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

Lean-to conservatories happens to be some of the most versatile and underestimated conservatory styles you’ll find in the market today and little wonder they’re so popular in the UK. Lean to conservatories, also referred to garden sun room, have been an integral part of the English garden for almost a century. Some of the common features of this extension is being spacious, having large expanses of glazing as well as a special low pitched roof. In other words, lean-to conservatories are able to offer extra space while maximizing natural light and can also be easily installed into awkward spaces.

If you’re also thinking about getting a lean to conservatory, then you’d probably want know the numerous benefits that comes with it. In this post, we’re going to consider some of the reasons why installing a lean to conservatory is a smart decision.

1. It’s easily adaptable to most property styles. Possessing simple lines as well as slim slightlines a lean to conservatory can fit several styles of both traditional and modern homes. In fact, the low pitched roof makes the entire structure a lot easier to fit in rather awkward spaces, making them the ideal choice if you’re have limited outside space.
2. It’s very cost effective. This conservatory style happens to be one of the most affordable and cost effective type of conservatory you’ll find around. Due to their simple design as well as structure, both the cost of installation and maintenance can be minimized, saving you some cool bucks.
3. It offers more usable space. Lean to conservatory’s large design and smart design makes it suitable to add an additional usable space to your home or property.

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

The process you need to go through to install a TV aerial depends on the type of aerial you have. If you have an indoor aerial, it’s simple. Just plug the aerial into your TV and stand it up next to it. If the signal isn’t right, then try moving your aerial closer to a window or higher up. Make sure you rescan for channels every time you move it so you know if you’ve made an improvement. It’s also fairly easy to install a loft TV aerial – just take it up into your loft and position it in a convenient place. Again, experiment with angles and positions to ensure you get the best signal. Installing an outdoor TV aerial is a little trickier. Ideally, try to fix your aerial to a wall or chimney at a gable end – this will be much easier to access than a chimney in the middle of the roof. Follow the instructions that come with your aerial for mounting it – it’s usually best to lash your aerial on rather than use screws. If you’re not used to working at height or aren’t confident doing your own aerial installation work, it’s best to get in touch with a professional.

Do Septic Tanks Smell?

The simple and shot answer to this question is yes, septic tanks smell. There are a plethora of very pleasant fragrant smells to enjoy in the United Kingdom, but the smell that oozes out of septic tank systems are certainly not one of them. In fact, if you care for yourself a lot, you should not even try smelling your septic tank at all. However, if you do notice a bad odour wafting from the direction of your tank, it may be that there’s an indication that something is not right. The septic tank system is always with strong malodorous scents, but when you start smelling the odour from the septic tank on your property, then something is wrong and if ignored, may lead to a contamination of your water supply and or other dangerous situations.

✓ When you’re able to perceive the smell of your septic tank from your property, it may imply a full or overflowing septic tank. In this case, you should call in a professional to have your tank pumped. Generally, most tanks are designed to be pumped every 4 years but this is definitely going to vary depending on the size of of the tank as well as your home’s water usage.

✓ Another possible reason for a smelly tank is a covered septic tank vent. This usually happens when a home is renovated or remodelled after the septic tank system has been fitted. You should make sure that the septic tank vents are always uncovered.

✓ If the septic tank starts to get smelly right after showering, then it’s most likely that the septic tank was not installed the way it’s supposed to and may have been fitted without any type of vent.

✓ A smelly tank can also be caused by inappropriate items making their way into a system like cooking grease, oil or fat, paints, solvents, industrial cleaning products, condoms, feminine hygiene products and so on.

You should replace your soffits and fascias if you are having problems. Soffits and fascias can degrade and rot away over time, and this can cause leaks, faulty guttering, or even allow pests entry to the roof space. If any of these problems occur, you should speak to an experienced roofline company to discuss replacing your soffits and fascias.

How To Clean Algae Off Roof Shingles

Stains and dirt on asphalt shingles can only make your entire house look shabby which can go a long way to hide away the true value of your building. In some cases, dirts and stains on asphalt roofing shingles are nothing more than a cosmetic issue. However, there are also times in which it goes far beyond this - when the stains are indicators of a problem that if ignored, can result in a serious roof damage and ultimately, roof failure. In most cases, it’s usually hard to distinguish these stains and hence, the more reason why your asphalt roofing shingles should be regularly cleaned and maintained. In this article, we’re going to look at how you can get rid of algae of your roof shingles.

Algae growth on roof usually have either blue, green or black stains. They normally begin with little spots which will develop into streaks overtime. These stains are mostly mistaken for moss or mildew and aren’t harmful to any other thing than the roof shingles. However, the look it gives the entire house is something nobody enjoys.

It should be noted that this is a task that deals with working at height and requires skills and confidence to pull off. If you lack any of these qualities, simply reach out to a professional for help.

✓ Safety first. Put on protective clothing.

✓ Apply a bleach solution with a garden sprayer and let it sit for up to 20 minutes

✓ Rinse the roof thereafter with the stream from the hose (do not use a pressure washer as it can damage the roof shingles)

✓ If there are still algae left after rinsing with water, you can make use of a brush with medium-stiff bristles to gently scrub the stains off. If some stains are still left, simply let the roof dry before repeating the process again.