Find a Shop Fitter you can trust in Penicuik.

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

How Much Does Plastering Cost?

If your existing interior or exterior plaster is starting to show signs of needing to be refreshed or the painting never seems to last, then it’s probably time to have your plaster renewed to breathe in a new lease of life to your decorating efforts.

So if you’re giving wall plastering a thought, there’s a need to have a rough estimate of the cost a professional is likely to charge so you can set a budget and start planning. However a direct answer can not be provided for this question as there are so many factors that a professional will put into considering before coming up with a quote that’s unique to your specific requirements.

A lot of plasterers will come up with a quote for the job using the number of square metres of wall space that’s going to be covered. This is due to the number of plasterboards as well as the other materials that the plasterer will need to purchase, how long the work will take and also the labour that’ll be involved in completing the project.

Another popular influencing factor that several plasterers use is the size of the room to be plastered. This is the main reason why you’re more likely to find the prices in small, medium as well as large rooms. Therefore, in order to have a more accurate estimate of the cost of your plastering project, you’d have to call in a qualified professional to have a look at the job at hand. Generally, to re-plaster a small room will cost within the range of £350 to £550, a medium room will cost within the range of £400 to £600 and a large room, between £550 to £700.

If you planning to invest in wall panels, it’s worth knowing whether or not they can be fitted over tiles. With the right installation advice from a reliable source, you’ll be able to save yourself both valuable time and money while also making sure that your home improvement project adds immense value to your property and gains from a durable and long lasting finish.

Wall panels, in general, are a cost effective means that you can incorporate to waterproof your bathroom or shower walls, while they’re also known for being incredibly stylish. Another significant benefit, that’s rather surprisingly often overlooked, is the fact that it’s actually a lot easier to clean and maintain when compared to wall covering that incorporates grout.

The short and simple answer to this question is yes, you can fit shower wall panels over tiles. However, it should also be noted that these may not be possible depending on your existing tiles’ conditions. This is because there are tiles that may not be suitable to be covered by shower wall panels. To protect the integrity of your shower wall panels and continue to enjoy it for any extended period of time, there’s a need to ensure that the existing tiles are in the right condition before you proceed. A beautifully finished and mould free bathroom will make your home stand out while also adding more value to it.

As a result, you’ll have to carefully inspect the tiles on the walls you want to cover before you proceed. While the odd cracked tile on a flat surface may not be an issue, all loose tiles should be completely removed (if more than two, you may want to consider removing all). You’ll also need to address other issues like damp or degrading plaster, uneven wall and more.

Plastering will fix small cracks in walls. Very small cracks may be fixed by simply reskimming plaster. More serious cracks will usually mean that you need to use new plasterboard or backing plaster. Larger jobs or deep cracks may need an experienced plasterer to come in.

Artex is a type of interior surface coating, similar to plaster. It’s used to create decorative textured finishes on ceilings and walls, so it takes longer to dry than plaster.

Artex is actually a brand name, but it’s used to refer to similar products made by other manufacturers too. It was particularly popular in the 1970s, but is still used to create attractive wall and ceiling finishes today.

How To Lay Tiles On Concrete

Installation of tiles on concrete sub-floors can be done with relative ease under adequate guidance. Here is what you have to do.

lPrepare The Concrete Subfloor

• Ensure the concrete is dry, clean and must be at least 6 weeks old.

• If there are dips and humps, level the concrete using a levelling compound.

lSet Out

• Working from the centre outwards, take a measurement of the floor (both length and width) and draw a cross at the centre.

• Lay out the tiles from the cross with a space of 3mm between each tiles. This will allow for movement stresses within the floor and later to be filled with grout upon installation of the tiles and adhesive dried.

lCut The Tiles

• Due to the particularly had nature of some floor tiles such as natural stone and porceclain, high quality tools are usually required to produce a clean cut through the tiles. With the help of an electric wet cutter alongside a slide cutter and nippers, your job would be made a lot easier.

• For a better result during intricate cuts, make use of a cardboard template.

lFix The Tiles

• The tiles should be fixed using a cement-based adhesive.

• Ensure to refer to the packaging or product data for the mixing ratios information.

• Stir the mixture till its lump-free

lApply The Mixture

• Spread the mixture onto the concrete sub-floor to create parallel ribs with the help of a floor trowel.

• Push the tiles into the parallel ribs.

• Clear out any excess adhesive from the tiles surface with a damp sponge.

• Do not walk on the tiles for at least 2 hours.

lGrout

• Once the adhesive is dried, wipe out any dust, adhesive or dirt from the tiles’ gaps.

• Mix about 4 to 5 parts of grout powder with 1 part of water and ix together.

• Apply the mixed grout diagonally across the tiles using a soft rubber grout float.

• Wipe out excess grout from the tiles surface and allow the tiles to dry.

• Stubborn residues can be cleaned using any washing up detergent with warm water within 24 hours after grouting.

Solid fuel engineers are everywhere, but finding one nearby for your project can be tricky and stressful, with both cost and reliability coming into question. This is even more worrisome when you’re fully aware that your solid fuel heating system potentials can only be fully maximized depending on how well it’s installed and how good your engineer or installer is. If you’re also facing the same challenge, then you’ve come to the right place. In this article, we’ll share with you some tips on how to choose a nearby professional and reliable solid fuel engineer who’ll ensure you get immense value for every penny spent. Let’s take a look!

✓ Ask for recommendations. To find a tradesperson, not just a solid fuel engineer, personal recommendations is the best way to go. Installation of a solid fuel heating system is a major undertaking which comes with a lot of costs, so if you’re going to do it the least you can do is ensure you do it right. Carry out your research, ask friends and family, neighbours and loved ones if the know of any reliable solid fuel engineer in the local area. If they’ve have one they’ve used, you can request for the cost, quality of the job done, the duration of the project and any other detail you feel you should know.

✓ Store contact lists. You’ll discover a long list of solid fuel engineers on many stores selling solid fuel boilers. These installers may not be affiliated with the store owners, but many stores see it as their responsibility to point you in the right direction so that the boilers acquired from them can be put to good use.

✓ Internet. With the rapid rise of online technology, there’s hardly a service you can’t find on the internet. Websites like Quotatis have been helping people find their desired service providers with relative ease for so long. To get the right solid fuel engineer online, it’s advisable to check reviews as well as testimonials before moving forward.

In several parts of the UK, air conditioning systems are a must especially in the warmer summer months. Fortunately, if your AC system isn’t functioning the way it’s supposed to, suffers frequent system breakdowns when overworked mostly during the hot summer days or perhaps you’re just tired of just having to manage with window units, the latest air conditioning units offers both features and performance that’s superior to the earlier models. And as you would have expected, each facet comes with a cost.

There are a number of factors that can determine the cost of an air conditioning unit. Out of all these factors, the size of your home happens to be the most significant factor that influences an air conditioning unit’s cost. Air conditioning systems are measured in tons, which is a measure of the amount of heat they’re able to remove from a home within an hour. As a rule of thumb, you’ll require about 1 ton of cooling per 500 to 600 square feet. Unfortunately, the square footage alone can’t be used to determine the tonnage. Other factors that’ll also play a significant role includes the efficiency of your most preferred AC unit, how well the home is insulated as well as the thermal nature of your home. On the average, a new air conditioning system for an average home should be within the range of £1000 to £3000 for a unit as well as the installation costs which can vary largely depending on the condition of your ducts. These figures may seem quite expensive, but when the hot summer days come, you’d be glad to have had one installed in your home.