Find a Shop Fitter you can trust in Builth Wells.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your business property, it’s only reasonable not only to expect the boiler to warm up your property efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several commercial gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

Air source heat pumps are a type of heating system that you can use to warm the air in your property. They’re a semi-renewable energy generator as, although they use electricity, they extract and use renewable heat from the air.

There are two main types of air source heat pump – air-to-water, and air-to-air. Air-to-water heat pumps are the most popular, and are best used to heat water that supplies underfloor heating systems or large radiators. Air-to-air pumps heat air, which is then dispersed round your property using fans.

Do you want a low carbon way of heating your home? Then, getting an air source heat pump is the way to go! What they do is pretty simple - they absorb the potential thermal energy present in the outside air and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. In other words, it functions by extracting heat from a cooler place and then uses it to raise the temperature inside a home or property. Being very similar to air conditioning units, the amount of heat they’re going to produce for your home or property will be dependent on the size you install. Therefore, the bigger the heat pump, the more the heat that’ll be generated.

Air source heat pumps have two main types which includes air to air and air to water. Air-to-water heat pumps works by absorbing heat from the outside air, then relays it directly into your home or property through the help of fans. In order to move the heat around your home, you’ll need a warm air circulation system. This type of air source heat pump are not eligible for the government’s Renewable Heat Incentive Payment as they can’t generate hot water. What’s more? They can function in reverse during the hot summer months.

Air-to-water heat pumps, on the other hand, operates by extracting heat from the outside air and transmitting it into the wet central heating system. Due to the fact that they’re able to generate heat that’s cooler than the one generated by a conventional gas or oil boiler, they happen to be a better fit for larger radiators or water underfloor heating.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

Cladding comes in a range of styles, such as flush, shiplap, and featheredge. Many types of cladding are also available in a variety of colours to suit any property. A cladding specialist will be able to discuss what solution is best for your property and how it works.

How To Lay Wall Tiles

Laying of wall tiles is a task that should be done with great caution, especially if you’re working on a tight budget. It is guided by its own unique set of rules which you do not dare to break if you wish to get it right the first time, and also to avoid incurring some additional costs. If you do not have a proper training or experience, laying of wall tiles is better left to a skilled professional for the best possible outcome. However, this guide will walk you through the various steps in the process to help improve your knowledge. Let’s get started!

lPrepare The Wall Surface

• Make sure the surface is clean, dry and smooth

• In wet areas, wall tiles should be fitted over a backer board

• If it’s a painted wall, ensure to sand the surface before installation.

lCreate The Layout

• Locate the centre of the wall

• Create an intersecting vertical and horizontal layout lines using a level

• Ensure to include spaces for grout joints when creating the layout.

lApply The Adhesive

• For wet areas, makes use of thin-set adhesive that’s cement-based.

• For dry areas, you can use pre-mixed mastic adhesive

• Follow the manufacturer’s instruction to prepare the adhesive

• Using a notched trowel, apply the adhesive (hold the trowel at about 45 degrees angle)

• Ensure not to cover the layout lines with the adhesive

lInstall The Tiles

• Follow the layout lines to install the wall tiles

• Place the full tiles firmly on the adhesive and twist slight and gently to make them fit.

• Use tile spacers to ensure constant gaps for grout joints.

lCut The Tiles

• After installation of the full tiles, there’ll most likely be a need to cut some tiles to fit.

• Cut the tiles with a wet saw or manual tile cutter

lGrout The Tile

• Ensure the adhesive is well dried and remove the tile spacers.

• Prepare the grout as instructed by the manufacturer.

• Use a rubber gloat to apply the grout.

• Remove the excess grout from the tile surfaces

• Wipe the tiles and joints gently using a grout sponge and clean water.

This is a question that’s very common amongst individuals looking for the best way to get rid of glass and reasonably so. Glass is a very dangerous and hazardous item which requires sensible precautionary measures to your waste disposal activities. If you are looking to dispose a whole glass, you should first consider giving it away to a friend or family who might be able to put it to good use. However if you are still concerned whether you can put glass in a skip, the answer is yes. And in fact, it’s probably the best glass disposal option that’s currently available, as it goes a long way to ensure user’s safety in the broken glassware pieces handling process.

Upon successful completion of your building’s construction or renovation, there’s a high chance a lot of broken glasses would be scattered everywhere and in need of immediate disposal efforts. The longer you ignore the glasses lying around, the higher the possibility of the glasses harming you or the construction workers. As a result, it is vital to make sure that the construction or project site is clean and free of any glass-posed hazards. Hiring a skip is your best bet to get rid of these harmful and unwanted wastes from your environment.

Wheelies are often considered to remove glasses especially from construction sites. However, due to the bulkiness and sharpness of glasses, it is crucial to incorporate heavy disposal equipment that are good enough to cut through the rubbish on the site. In addition, it’s not advisable to dump your broken glass in recycling bins, as it poses great threat to the waste disposal team collecting the recyclables. If you’d ever need to put your glass in a skip, ensure to insert them in boxes or wrap them up with paper before removal to enhance user’s protection. Click here to learn more about skips.

Driveway work is usually done in the warmer half of the year. This is partly to avoid bad weather. If you want to get ahead and avoid waiting for a contractor to be free, you should try getting in touch with a professional in the early spring so a date can be booked for install as soon as practically possible.

Should A Professional Replace My Conservatory Roof?

As your first and primary line of defence against the harsh weather conditions or elements, there’s the need for your conservatory roof to be in pristine condition at all times. This will enable it to keep your conservatory safe and dry, while also helping to protect its structural integrity. When you have a reliable roof over your head, your conservatory will be free of any weather-related damage. Consequently, highlighting the importance of regular maintenance of your conservatory roof.

However, over the years, there’ll come a time whereby maintenance and repairs will no longer be a wise decision. When this occurs, you know it’s high time you replace your conservatory roof to continue enjoying the structure’s numerous benefits all year round. Getting a professional to replace your conservatory roof is crucial for several reasons, let’s have a look!

✓ Knowledge and expertise. Conservatory roof installation experts are well trained and also possesses the required knowledge to work at height while also being able to guarantee the best results which will save you both time and money.

✓ Giving your conservatory a new look. Replacing a conservatory roof isn’t as simple as it seems. Trying a DIY without prior experience and knowledge can end up disastrous and making the new roof even more unsafe and unappealing than the old roof. When done by a professional who knows his way around the roof, you can be rest assured that your new conservatory roof will come out picture perfect.

✓ Saves you money and time. What would take a professional just a couple of days to complete is most likely to take a DIYer several weeks to get done and more often than not, end up with a disastrous result. To save yourself the stress, time and money, calling in a professional is your best bet.