Find a Shop Fitter you can trust in Broseley.

If you’re thinking about the better option between tiling your walls either before or after fitting a kitchen, you’ve come to the right place! In this article, we’ll give a good insight on the best practices to help you plan and also avoid making costly mistakes.

The short and simple answer to this question is - it depends. It depends on structure of your home or property, your kitchen as well as the surface in question, the materials selected and also your unique preferences. This answer is mainly provided because there’s no tile industry standard explaining when a kitchen or cabinet should be fitted. Therefore, there’s a need to check the suitability of any structure and substrate needs by a professional before you determine the type of tile installation as well as when to install the tile.

If you decide to install the wall tiles before fitting the kitchen, here are some benefits you stand to derive:

✓ There will be no finish cuts or sealant application required for the perimeter joints at the finished sides of the cabinets making the installer’s job a lot easier

✓ This also implies extra square footage for the installer, but less detail as well as trim work.

✓ Water leaks from the kitchen won’t be able to cause much damage.

✓ It allows for more flexibility when remodelling in the future.

However, installing the wall tiles after fitting the kitchen also comes with some advantages. Let’s have a look!

✓ This means less in square footage, but more time in both detail as well as trim work.

✓ The risk of damage to the wall tiles by other trades is significantly minimized.

✓ It’ll be easier to change the wall tiles later on without having to remove the kitchen.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

We all know how helpful air conditioning systems can be especially during the hot summer season which is great at making your home feel nothing less than an inferno. So if you have an AC system, you’d probably want to know if leaving it on will be cheaper and more efficient.

The short and simple answer to this question is yes, leaving your air conditioning system on will make make it cheaper and more efficient. This isn’t what you or many other people will have in mind though. Under no circumstances should you leave you air conditioning system on full blast 24/7. To make your air conditioning system more efficient by leaving it on has a right and wrong way you can go about it. Let’s have a look!

If you’d ever noticed, any time you turn your air conditioner off during a very a hot day, even if it’s for just a couple of hours, things tend to get thrown out of balance pretty quickly. When turned back on, your AC system will have to work even harder to restore the usual comfort levels in the room. When you abuse this dial in such a fashion, the AC system can only become more inefficient rather than making your home more comfortable quickly.

On the other hand, your AC system ( when tuned to the right settings) can help maintain the proper temperature and humidity balance within your home instead of turning it off while away. And upon getting back, you can simply turn down the thermostat a bit which helps you prevent the usual stagnant air that you’d be hit with when your return home (with the AC system turned off) that’ll have you racing for the dial.

Yes. Commercial architects can provide a wide range of extra services such as project management, site feasibility studies, and help with site purchase. They can also be a great source of information and advice throughout the design and build process.

How To Remove Tile Adhesive From Wall

Do you feel your tile design choices are outdated and want to replace it with a more stylish one? Or perhaps you’re just struggling to remove the old tile adhesive from your wall. Putting on a new wallpaper or repainting your wall might be a cup of tea, but retiling is surely a different experience altogether. After detaching every single piece of tile from the wall, you’ll still have the strongly glued adhesive to battle with. If not done properly, you may as well damage the wall which will trigger a new additional cost for repair. We’d recommend you get a professional helping hand for the best results if you’re without a proper training or experience. However, this guide will teach you everything you need to know about the process. Let’s get started!

Materials Required

• Steamer

• Protective sheets

• 4-inch scraper

• Clean cloth

• Protective gear - face mask, eye goggles, gloves.

Tile Adhesive Removal Process

• Cover The Floor

Ensure that the floor is well covered to collect the residues falling off from the wall with some protective sheets.

• Heat Up The Adhesive

Using the wallpaper steamer, heat up the adhesive to make it a bit loose and softer. Do this by slowly moving the steamer around and ensure not to stay on one spot for too long.

• Scrape Off The Mortar

When you can tell the adhesive is properly softened, use the 4 inch scraper to wipe it off the wall. Do this until all the adhesive has been completely removed.

• Clear Out The Fallen Residue

Clean up any mortar that has fallen on the floor.

After the tile adhesive removal, your wall may need to be skimmed depending on its state. This is to put the surface in a good and flat condition before installing the new tiles. The wall may also need to be re-plastered if the adhesive is extremely strong.

Garden slabs are a joy to behold but only when done the right way. Well, the installation of paving slabs shouldn’t be exceed digging a little here and there, buying a small amount of mortar and pressing down the garden slab, right? Absolutely not! But we must admit how great it would have been if only it were that easy in real life. Let’s be honest, in reality, laying garden slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. Consequently, this happens to be a stressful and quite tricky challenge. If you lack the required confidence to pull this off, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the garden slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

1. Mix a layer of mortar for each paver.
2. Apply the mixed mortar onto the sub base by using the trowel.
3. Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.
4. Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.
5. Take a measurement of the gap between the pavers
6. Repeat the above steps until all pavers have been perfectly laid
7. Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.
8. Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard-bristled brush.

In several parts of the UK, air conditioning systems are a must especially in the warmer summer months. Fortunately, if your AC system isn’t functioning the way it’s supposed to, suffers frequent system breakdowns when overworked mostly during the hot summer days or perhaps you’re just tired of just having to manage with window units, the latest air conditioning units offers both features and performance that’s superior to the earlier models. And as you would have expected, each facet comes with a cost.

There are a number of factors that can determine the cost of an air conditioning unit. Out of all these factors, the size of your home happens to be the most significant factor that influences an air conditioning unit’s cost. Air conditioning systems are measured in tons, which is a measure of the amount of heat they’re able to remove from a home within an hour. As a rule of thumb, you’ll require about 1 ton of cooling per 500 to 600 square feet. Unfortunately, the square footage alone can’t be used to determine the tonnage. Other factors that’ll also play a significant role includes the efficiency of your most preferred AC unit, how well the home is insulated as well as the thermal nature of your home. On the average, a new air conditioning system for an average home should be within the range of £1000 to £3000 for a unit as well as the installation costs which can vary largely depending on the condition of your ducts. These figures may seem quite expensive, but when the hot summer days come, you’d be glad to have had one installed in your home.

How to joint pave or grout paving slabs is a common question asked by several home owners. Most times they may have some existing paving and thinking its high time to have them re-pointed or laid some new pavings and wondering how to fill the gaps.

In the UK, patios don’t get much use especially during cold winter months. However even when not in use, the combination of wet weather and cold temperatures is capable of having the hardest outdoor living spaces looking a bit neglected. This may lead to cracked grouting which leaves gaps between stones making way to a place where weeds can grow and flourish during spring. You definitely wouldn’t want your outdoor living space looking this messy. Hence, there’s a need to get your patio back on track by grouting the paving slabs. However, if you lack proper training or experience, it’s advisable to employ a reliable professional who can guarantee the best results. In this guide, you’ll learn more about the paving slabs grouting process.

• Saturate the area that needs to be repointed with the help of a hosepipe and/or watering cans. Use a yard brush to distribute the water across the paving slabs.

• Pour a generous amount of your compound product over the newly soaked patio.

• Sweep the into the joints where it’s needed with the help of a broom. Do this carefully in order to make sure each and every joint is fully filled with the compound. If done right, this can help prevent premature cracking for a long period of time.

• Once the joints are filled with the compound, brush aside the exces product and strike it in. Ensure that the product is pressed firmly into each gap leaving behind no spaces.

• Sweep out the excesses which can be kept for future use.