Find a Shop Fitter you can trust in Shifnal.

First and foremost, it must be stated that replacing an existing electric shower is much easier than fitting one from new. This is primarily due to the fact that the main components required which includes the water pipes as well as electrical connections will have already been established. In this post, we’re going to assume that all these are already in place which means you’re replacing an existing electric shower with a new one. It’ll also be an advantage if the preferred electric shower features cable and pipe entry points at the top and bottom as well as the rear and side so as to allow for more flexibility when it gets to routing cables and pipes. If you’re not confident enough to pull off this task, then it’s strong advisable to call in a professional who can guarantee the best results the first time. Here are the steps you can follow to fit your electric shower:

• Disconnect the power supply as you probably know water and electricity aren’t particularly the best of friends. Once done, you’ll also need to turn off the water supply
• Remove the shower unit. Many shower units are secured with four screws which makes the removal rather straightforward.
• Examine the shower connection points to determine if they’re in the same place on the new unit as they were on the old one.
• Install the new shower unit. First, you’ll have to mark the position of the new units on the wall using a pencil. If the new units don’t possess the same silhouette as the old one, you’ll have to drill new ones preferably using a masonry drill bit.
• Check your installation at both the electrical and water supply to ensure the connection is made correctly.
• Test your new electric shower by turning the power and water supplies back on.

How To Repair Roof Leak

Asphalt shingles are the most popular roofing material options for most UK homes in recent times. Thanks to them, roof repair is now all about identifying the leak and sealing it the right way. If you’re a competent DIYer and confident enough to pull this off, then this should be done within a short period of time and saving you money as well. However, if you don’t have the confidence to pull this off, then calling on a professional roofer who can guarantee the best results will be your best bet. In this article, we’ll consider four simple steps you can take to repair an asphalt shingles roof.

✓ Locate the spot of the roof leak. Roof leaks are mostly made evident by water stains on the ceiling. Simply note the spot of this water stain, grab a good pair of binoculars, then go outside to identify the location of the roof leak. Search the area for any curls, cracks, missing shingles or anything that looks odd. Leaks can also occur at any spot where caulking and flashing have been affected or compromised.

✓ Secure curled shingles. To do this, simply brush on a generous amount of asphalt roofing cement to the underside of the shingle and press firmly to set.

✓ Replace damaged or missing shingles. In the event whereby the shingles are cracked, rotten or missing, your best bet would be to have them replaced. Simply remove the damaged shingle then slide in the new one under the one above and align it with those on either side. Once done, you can then secure it with 6d galvanized roofing nails at each corner. After completion, make sure you cover the nail heads with roof cements.

✓ Fix flashing. To do this, simply reseal joints with the help of a caulk gun loaded with roofing cement.

Due to the fact that wood pellet boilers are contingent on eco-friendliness and cost efficiency, they’re gradually growing in popularity amongst home or property owners. It offers a viable alternative to other types of boilers such as oil fired boilers, gas boilers or electric boilers partly due to government’s Renewable Heat Incentive scheme which makes it more affordable to operate when compared to traditional boiler systems. Although there are several kinds of boilers available in the market today, but as the name suggests,wood pellet boiler makes use of wood pellet as the heating source. So if you’re thinking about installing a wood pellet in your home or property, you’d probably be interested in knowing how much the home appliance would cost. In this article, we’ll give you a rough estimate of the cost to help you make informed decisions.

When purchasing a wood pellet boiler for your home, one of the first thing to consider apart from the cost is the is the storage space needed to keep the pellets, which is usually given in plastic sacks. However, if you don’t have the storage space, you’ll have to spend a certain amount of your budget so as to construct a storage room specifically for the boiler.

In general, a standard wood pellet boiler will cost within the range of £4000 to about £6000, although you’re most likely going to put the pellets into the boiler by yourself, which may actually prove to be inconvenient in the long run if you’re going to do it on a more frequent basis. However, there are more expensive versions which are able to feed themselves automatically. The cost of these versions are usually up to £10,000 upwards.

Patios use durable and hard wearing materials which will be able to withstand extreme weather. It’s important to consider the drainage of your patio, as heavy rain will need to drain away to an area that can absorb the water. A professional will be able to design and lay a patio to do this.

Some properties are unable to have double glazing, especially those in conservation areas or listed buildings. To counter this problem and still benefit from a warmer home and cheaper bills, secondary glazing is an option. Secondary glazing is a second pane fitted inside your original window. Secondary glazing will still save you around £105 yearly.

If you look after your air source heat pump, it can last for over 20 years. Make sure you check it every year and get a registered or qualified installer to check it every 3-5 years to prolong its life. If in doubt, check the manufacturer’s maintenance instructions.

Lean-to conservatories are often known as Mediterranean conservatories or sunrooms and are a great way to add more living space when you’ve only got a small amount of room to work with. They usually have clean lines, a rectangular shape and attach to the side or rear of your home, which makes them one of the easiest conservatory types to build yourself.

So how do you build a wooden lean-to conservatory? The first step is to decide what you want it to look like. Most lean-to conservatories are constructed of glass and the wood frame, but you can choose to have dwarf walls too. Dwarf walls are low brick walls that are useful if you’re planning to plumb in radiators, have air conditioning installed or put plug sockets in the conservatory.

When you’ve decided what your wooden lean-to conservatory is going to look like, you’ll need to get the materials. You’ll need to choose a hardy wood – oak is the most expensive but also the most durable – and source glass for the windows. You’ll also need to decide on a roof material and work out the correct pitch.

The first step to building your wooden lean-to conservatory is to dig the foundations. You’ll then need to level the earth, then add concrete to the correct height, which should be lower than your property’s existing damp course. Then, you’ll build up to the damp course, which will be your conservatory’s floor level. Don’t forget to make sure it’s even.

If you’re building a dwarf wall, start it from the base and build up to no more than 1 metre high. Once the cement is dry, place external sills on top of the dwarf wall. You’ll then need to secure the frames; start with the one that secures to your property, then do the same for the rest, connecting outwards until they meet from the two sides. Then put up your doors.

Now it’s time to build the roof. This should be simple if you’ve bought your own custom-made kit. Place the roof ridge on top of the frames, then add the roof rafters between the roof ridge and hip bars. Fit your glazing sheets and guttering – it’s important that your wooden conservatory roof has guttering just like your house, otherwise your conservatory roof won’t last very long and could even cause rainwater to rot your wooden frames.

Once you’ve built your wooden lean-to conservatory, all that’s left is to decide on how you want to decorate it. But if this all sounds like too much, get in touch with specialist wooden conservatory installers who will be able to give you a quote for building you a lean-to conservatory.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.