Find a Shop Fitter you can trust in Wincanton.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How To Lay Tiles On Concrete

Installation of tiles on concrete sub-floors can be done with relative ease under adequate guidance. Here is what you have to do.

lPrepare The Concrete Subfloor

• Ensure the concrete is dry, clean and must be at least 6 weeks old.

• If there are dips and humps, level the concrete using a levelling compound.

lSet Out

• Working from the centre outwards, take a measurement of the floor (both length and width) and draw a cross at the centre.

• Lay out the tiles from the cross with a space of 3mm between each tiles. This will allow for movement stresses within the floor and later to be filled with grout upon installation of the tiles and adhesive dried.

lCut The Tiles

• Due to the particularly had nature of some floor tiles such as natural stone and porceclain, high quality tools are usually required to produce a clean cut through the tiles. With the help of an electric wet cutter alongside a slide cutter and nippers, your job would be made a lot easier.

• For a better result during intricate cuts, make use of a cardboard template.

lFix The Tiles

• The tiles should be fixed using a cement-based adhesive.

• Ensure to refer to the packaging or product data for the mixing ratios information.

• Stir the mixture till its lump-free

lApply The Mixture

• Spread the mixture onto the concrete sub-floor to create parallel ribs with the help of a floor trowel.

• Push the tiles into the parallel ribs.

• Clear out any excess adhesive from the tiles surface with a damp sponge.

• Do not walk on the tiles for at least 2 hours.

lGrout

• Once the adhesive is dried, wipe out any dust, adhesive or dirt from the tiles’ gaps.

• Mix about 4 to 5 parts of grout powder with 1 part of water and ix together.

• Apply the mixed grout diagonally across the tiles using a soft rubber grout float.

• Wipe out excess grout from the tiles surface and allow the tiles to dry.

• Stubborn residues can be cleaned using any washing up detergent with warm water within 24 hours after grouting.

Are you looking to replace your old window for a new double glazed window and wondering what it’s going to be the cost? Well, the double glazed windows market is a very competitive one in the UK with varying prices across the country. Therefore, if you shop around you’re most likely to find something that’ll fit your budget both products and quality wise.

As you would have expected, the more windows you required the more money you are going to spend. However, the cost per window is likely going to be lower depending on the number of windows you purchase. Several double glazed windows come with a 10 year warranty but it’s advisable to also obtain a solid workmanship warranty which provides coverage for any potential problems for a good period of time upon installation.

To determine the cost of double glazed windows, there are so many things to put into consideration that just the primary dimensions of the window itself. Other factors that works to decrease or increase the cost of the project includes the frames’ quality as well as the material used. For example hardwood can be quite high priced when compared to uPVC.

The number of opening windows within the frame can also play a huge role in the cost of the windows as well as the type of the glass. The cost of a double glazing window usually ranges between £100 to £3,200 per window, depending on the available options.

To have a more accurate estimate of the cost of a double glazing window, you’ll need a obtain a survey from a double glazing installer who can take into account any possible complications that may arise when installing your windows while also giving an advise on the most suitable window style for your property.

How To Lay Wood Flooring

Laying of wood flooring is actually a very simple task contrary to many beliefs. First and foremost, before commencement of the fitting process, you must determine the direction you would like the engineered wood flooring to lie in. To do this the right way, they should lie in the direction of the the longest wall. However, if your subfloor is wooden, then having the boards positioned across the joists underneath would be your best bet to get started.

Here are some simple steps to follow to properly lay your wood flooring:

• Start from a corner, working from left to right and place the initial rows of the boards with the groove’s end directly opposite the closest wall.

• Make use of expansion spacers. Place them in between the wall and the board alongside an expansion gap of about 8 to 10mm.

• Place the board’s final rows at about 100mm wide. To achieve this, it is crucial to be pro-active with the measurement and cut the boards (if you deem fit) to adjust the first row.

• With the help of the click system, the boards will click together.

• Fit in the next board. Ensure to attach the tongues together (30 degrees from the floor) and once done, you can proceed to lower and lock it in place. Do this till you get to the end of the row.

• Cut the last board of the row to size if its too long.

• If the part cut off is up to 300mm, simply use it to start the next row. If not, cut a new board in half to use.

• Put the rows side by side in such a way to ensure the joints are staggered at each and every row. Keep a consistent gap between the wall and the planks via the continuous use of the spacers.

• Lay a plank over the last row to determine the width of the previous board. Position a new plank in a way that its tongue is directly against the wall. Once done, proceed to mark a line of plank underneath to get the required width. Then, fit the plank into the space with the help of a pull bar and hammer.

Click here to learn more about wood flooring.

This varies according to the quality of the conservatory and installation work. If these are both high quality, your conservatory should last at least 25 years. But obviously if you notice deterioration or leaks, then this could be an early warning sign that time is running out.

Intruder alarm systems work in various ways and all with one goal in mind - ensuring the safety of both the building and valuables. Whether it’s a small or big home or property, there is a wide range of systems that can be installed to guarantee adequate protection from unwanted visitors. They work with various applications and you get to determine the action to be made in the event whereby the protected zone is violated and system triggered.

Intruder Alarm Systems come in three main types which includes:

• The Bells-Only Intruder Alarm System - Whenever there is a violation, the only action would be to trigger the alarm, nothing more.

• The Communicators - These alarm systems are basically speech dialers which automatically sends a message to various selected number whenever there is an intrusion.

• Monitored Systems - Here, the monitoring centre would be alerted once there is a breach in security.

However, irrespective of the type, most intruder alarm systems operate following a similar series of steps.

lSensing of motion. The systems usually feature door and window sensors which detects any contact of the door/window in the frame when shut. There are also the motion sensors which can be strategically stationed across the property to detect any motion and possible breach of security.

lTriggering of the control panel. The system is interconnected, and all components are linked to a control panel where all detectors’ and sensors’ generated informations are relayed. The alarm countdown is activated in the event whereby a contact is made and circuit impacted.

lSounding of the alarm - Once the alarm countdown has been initiated, failure to insert an abort code will ultimately sound the alarm. The external sounder that comes with the system produces a loud sound to notify people about the security breach or intrusion. There is also an interior sounder which works to bring the presence of an intruder to the awareness of the occupants.

lDeactivating the alarm. With the control panel, users can easily activate/deactivate the alarm system via a fob, code or selected smartphone apps. Click on the link to learn more about intruder alarm systems - https://alarm.quotatis.co.uk/3-ways-home-security-systems-keep-safe/

So you’ve decided to add some new French doors for your home? If yes, then you’re likely going to be concerned about whether or not you’ll require a planning permission to get started.

Properties are compelled to meet certain requirements and have proper permission in place in order to be in line with the regulations. Overall, you’re going to need planning permission in the following situations:

• If you want to construct something new.

• If you want to a make a major change to a building like an extension.

• If you want to change the use of your building such as converting it from residential to commercial.

Getting a new door or replacing an existing one doesn’t usually require a planning permission as it’s one of the less complicated improvements you can make to a home. As a result, this kind of improvement is normally covered by permitted development rights especially when you’re not constructing an extension for which to use the French door. However in the events whereby a permission is needed, it will most likely going to be granted if the proposed changes does not have an impact on the primary elevations of the house which is usually the front of the building.

It’s also important to note that permitted development can be limited by local authorities. These limitations include buildings in a conservation area, listed buildings, and if you happen to reside in an area of immense aesthetic appeal or other designated areas like National Parks. If such situation before you change your French doors, it’s important to consult your local authority before proceeding.

The amount of maintenance will vary depending on the material of the gutter. However, all gutters should be cleaned regularly. Ideally cleaning should be carried out yearly, or more frequently if there are trees close to the guttering, this prevents overflows and problems elsewhere.