Find a Shop Fitter you can trust in Eye.

Scaffolders erect and pull apart provisional metal scaffolding on constructions and building sites, so that other individuals can labour at elevation and carry out their jobs without harm. Scaffolders are generally in charge of putting up the scaffolds outside and inside the building being constructed, renovated or even demolished.

Although there are no official credentials required to become a scaffolder, there are numerous ways you could take to help you follow this career path. You may perhaps complete a college course, a traineeship or apply straight to an employer for work. You ought to explore these paths to becoming a scaffolder, to find out which is the correct one for you. Even though some of these choices have certain qualification necessities, many employers are more concerned in individuals who are passionate, keen to learn and can follow orders. A CSCS card (Construction Skills Certification Scheme) might be needed for you to be able to work on a construction site.

College/training provider

Although there are no set admission necessities, anyone given a career as a scaffolder would profit from reaching GCSE qualifications (or equivalent) in maths and English. To start as a scaffolder, you will have to get a Level 2 certificate in Construction Operations or a Level 1 Certificate in Construction Skills.

Work experience

Work experience is indispensable to securing employment inside the construction business. You can get this at school, or you may choose to work on weekends and holidays with a company or relative who works as a scaffolder. Possible employers will always be delighted to see work knowledge listed on your CV.

Some of the desirable skills for a scaffolder:

• Confidence to work at heights.

• Hand-eye coordination should be excellent.

• Should have a healthy level of physical fitness.

• Ability to interpret technical drawings.

• Have excellent written and verbal communication skill.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

It’s up to you what size gravel you use for your driveway, but there are some guidelines that are worth following. If you go too small, your gravel will get displaced easily. But, if you go too big, you driveway might be quite tricky to walk on. Generally, it’s a good idea to go for a gravel size somewhere between 10-20mm.

For a variety of reasons, Indian stone driveway happens to be a prominent choice for driveways among residence as well as property owners in the UK. Not only is does it have a vast array colour account as well as really easy to maintain, however its additionally very long lasting and also long-term, as well as increases the worth of your home. With all the numerous benefits, it's rather normal to be attracted right into hurrying to have the paving alternative fitted on your residential property. However in reality, to really delight in maximum benefits from your Indian stone driveway, there are some points that must be taken into factor to consider before you make a financial investment choice. In this short article, we're going to check out these aspects to aid put you in the right instructions. Let's take a look!

• Is the surface suitable? This is a really essential inquiry to ask prior to buying choice. In order to recognize whether Indian stone driveway is an ideal choice, you'll need to first identify if it matches with your supreme driveway leading goals. If you require a tough appearing choice that's extremely durable, aesthetically appealing and climate resistant, then Indian stone paving appropriates.
• Is there any damage. In case whereby your driveway is harmed in one method or the various other, it must be fixed before moving on with the Indian stone paving setup. Failure to do this can result in a significantly much shorter lifespan for your Indian stone driveway.
• Is the installer guaranteed? In order to shield yourself and have a peace of mind throughout the Indian stone paving installment on your driveway, there's a demand to guarantee that the expert employed is insured. Otherwise, in case where something goes wrong during installation, you might need to foot some or all the economic burden.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

This is a very sensible question to ask especially before making any decision. However, the answer is not always straightforward without conducting a proper survey of the site in question. In a stark contrast to many beliefs, a “standard garage door does not exist. And as a result of the great variety in specifications, there’s usually a need for garage door to be made to order.

Roller garage door are gradually becoming more and more accepted by homeowners across the country and reasonably so. The fact is, they’re the only type of garage door that features an electric motor as a standard rather than an optional extra. Therefore, if you’re considering the installation of a new garage door and wish to know more about the cost of getting a roller garage door, we’ve got you fully covered!

One thing you should take note is that the prices can vary due to garage door manufactures, price increases as well as the size and type of the garage door you want installed. However, here are the mostly likely price ( including both VAT and installation) you’ll pay to get a roller garage door in the UK.

• For an insulated roller garage door with a single garage door size, the price will range between £1099 to £1800.

• For an insulated garage door with a double garage door size, the price will range between £1400 to £3000.

• For an electric and insulated roller shutter garage door with a single garage door size, the price ( without VAT & installation) will range between £250 to £300.

• For an electric and insulated roller shutter garage door with a double garage door size, the price ( without VAT & installation) will range between £350 to £400.

Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.

✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.

✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.

✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.

✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.

✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.

✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.

✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.