Find a Shop Fitter you can trust in Haslemere.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

How To Install Bifold Doors

If you’re looking to install a bifold door in your home or property, then you’re at the right place! In reality some jobs are better left to the professionals and one of such jobs is bifold door installation especially if you lack proper training and experience that’ll guarantee the best result the first time. If otherwise, hiring a professional installer will do you lots of good like saving you time and extra money that could result from costly errors. In this step by step guide, we’ll take you through the bifold doors installation process.

The first step to take when it comes to bifold door installation is to take the measurement of the door opening and get a kit in the appropriate size. For a better accuracy, do note that the combined measurement of both doors should be about an inch less than the opening’s total width while also being two inches less than the door frame’s height.

• Install the top rails in such a way that the rail’s end makes contact with the door frame’s side using the screws.

• Fit the bottom rail in the same fashion as the top ensuring the rail’s end makes contact with the same side of the door frame.

• Insert dowels into the predrilled holes in the door panels’ top.

• Place the dowel with the adjustment screw near the bottom’s side wall. While placing the fixed dowels in the door panel’s top and bottom on the side farthest away from the hinge. Once done, put the dowel and spring assembly into the door panel’s top, closest to the side wall.

• Fit the door panels into rail’s top and bottom while also adjusting the screws to centre the doors.

• Ensure the doors open and close like they should. If positive, tighten all hardware and fit the pulls or knobs of the door.

Sealing your driveway isn’t 100% necessary, but it is recommended. It will help keep your driveway in good condition and increase how long it lasts. Sealer should be applied approximately once every 2 years, or when your driveway begins to show signs of deterioration.

Kitchen floor tiles are a very popular choice for several reasons. They’re durable, visually appealing, resistant to moisture and stain and also relatively easy to maintain and install especially when compare to wall tiles. This is a task that can be done by any competent DIYer but requires a lot of patience as well as confidence. If you lack these attributes, then we’d recommend that you hire a professional floor tiler who can guarantee the best results the first time. In this article we’ll take you through the kitchen floor tiling process. Let’s get started!

• Prepare The Subfloor

✓ Ensure the subfloor is very secure to support both the tile and the people working across it.

✓ If necessary, you can strengthen the kitchen floor with the help of a vinyl, heavy felt or any other good backer board.

✓ After successfully securing the floor, proceed to clear out all dust and dirt.

• Mix The Mortar

✓ Mix a thinset mortar be referring to the instructions on the package. ( Mix only the quantity you can apply within 30 minutes).

✓ Once the mixture looks similar to the thickness of mayonnaise, allow it to rest for about 10 minutes before application.

• Apply The Mortar

✓ Apply a thin layer of mortar

✓ Do not cover extensive areas as the mortar can become very dry.

✓ Spread the mortar with a trowel in curved patterns to make it flat on the floor.

• Set The Tile

✓ Set down the tile slowly, apply a little pressure until its holds firmly to the surface. ( Apply a consistent amount of pressure throughout to ensure equal heights for all the tiles)

✓ Continue with the process until all full tiles are well positioned

• Cut The Tiles

✓ Once all the full tile pieces are in place, start cutting to cover the edges requiring smaller tile pieces.

✓ Take accurate measurements of the outer edges needing smaller tile pieces.

✓ Cut the tile pieces to fit the measurement taken with the help of a wet saw or hand tile cutter.

• Grouting

✓ Remove all spacers and mortar residues and lay the grout

✓ Apply the grout along the tiles’ seams with a grout float

✓ Clean out excess grout with a damp sponge after leaving it to dry for about 30 minutes

✓ Once the grout is fully dried, apply the sealer (the drying process normally takes within 3 to 4 days).

Given the poor reputation of wireless alarm systems over time for being largely unreliable, it’s no surprise many potential investors are curious to know how wise a wireless alarm system purchase decision is. The main issue with the older models is the fact that they possess an inadequate monitoring capabilities as well as receiving range which makes it hard to detect signals of intrusion or potential failures. Hence, this makes the older wireless models totally unreliable.

However, the immense improvement in the wireless technology has ultimately made the newer versions a lot more reliable. Although, in rare cases, they might be affected by some interferences which can result in the malfunctioning of the sensors. Overall, with proper care and maintenance, wireless alarms can be just as reliable as the wired alarms.

Here are some of the advantages of using wireless alarms:

• Due to the little amount of wirings incorporated, a wireless system is significantly neater than the wired system.

• They are very easier to install and consumes little time

• Wireless alarm systems are highly flexible. To expand your system, you can include door or window sensors and motion sensors.

• The system’s security options enables the connection of smart devices to your alarm via a network connection. As a result, you can easily activate or deactivate your alarm and get alarm notifications via your Smartphone.

• They are very portable. This implies you can always carry your alarm with you if you ever decide to relocate.

• You get to benefit from systems with a key fob and other wireless-enabled features.

• Wireless alarms are user-friendly, making it very easy and quick to install and set up.

With the above mentioned points, you can be rest assured that a wireless alarm is now more secured than ever and a good option if you wish to install a home security system.

How Often To Service Boiler?

A boiler is a vital part of any home especially if you’re in the UK. Not only does provide your entire household with hot water and keep them warm but also adds a good value to your property. Boiler repairs and replacement are both super expensive and stressful, so in order to avoid all these worries, it’s better to have your boiler serviced on a regular basis for your own peace of mind. When you call in a reliable heating engineer, it can immensely raise your boiler’s efficiency while also saving you from more expensive issues down the road.

So if you haven’t had your boiler serviced for quite some time, moved into a new house and not aware the last time your boiler was serviced or perhaps you’re just wondering how often a boiler should be serviced, then you’ve come to the right place! The short and simple answer to this question is a boiler should should be serviced once in a year, and most preferably during the summer months. However, there are a wide range of factors that comes into play so it’s always advisable to check with your manufacturer before you proceed.

According to the law, you’re required to have your boiler services on an annual basis. Failure to do so can render your boiler or home warranty void. Therefore, it’s very crucial to take down the last time your boiler was serviced and also set a reminder to book your next appointment when the time closes in.

If you happen to own an electric boiler you may not need an annual servicing. But you may still be required to perform it annually by your insurance provider.

If you want to give your concrete paving slabs a new lease of life, it’s possible to paint them. This is a great option if your slabs are looking tired or you want a new look, but you don’t want to invest in new paving.

Before you go ahead, you need to make sure that your slab paving is clean and dry. And if it’s been sealed, you’ll need to strip this off. Make sure you get a paint that’s specifically designed for the job so you get the best results.