Find a Shop Fitter you can trust in Redhill.

The process you need to go through to install a TV aerial depends on the type of aerial you have. If you have an indoor aerial, it’s simple. Just plug the aerial into your TV and stand it up next to it. If the signal isn’t right, then try moving your aerial closer to a window or higher up. Make sure you rescan for channels every time you move it so you know if you’ve made an improvement. It’s also fairly easy to install a loft TV aerial – just take it up into your loft and position it in a convenient place. Again, experiment with angles and positions to ensure you get the best signal. Installing an outdoor TV aerial is a little trickier. Ideally, try to fix your aerial to a wall or chimney at a gable end – this will be much easier to access than a chimney in the middle of the roof. Follow the instructions that come with your aerial for mounting it – it’s usually best to lash your aerial on rather than use screws. If you’re not used to working at height or aren’t confident doing your own aerial installation work, it’s best to get in touch with a professional.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

Is your garage door a bit old and outdated? Are you planning to make some renovations? Or perhaps you just want a newer and more stylish garage door, that’s safer and easier to operate, installed. Fitting a garage door can be a bit tricky but it’s not as difficult as you might think. If you’re without proper training or experience, it’s advisable to get in touch with a reliable professional for help in order to guarantee the best results while also saving you both time and money. This guide offers you step by step instructions to assist you in the installation of a new door on our garage.

To get started, the obvious first step is to remove the old garage door. Carefully go through the manufacturer’s instructions to achieve this. Here, you’d basically have to unlatch the door, take apart the door’s panel and unscrew the tracks.

lMeasure, Fit The Hinges & Handles

• Take a measurement of the area in which the door will be fitted

• From the top of opening to ceiling should include a space of about 10 to 12.

• For the length of the garage, you should have the door’s height with about 18 or more space.

• Once done, attach stops to the sides of the opening

• Lay out the bottom piece of the door and include the weather stripping (if you deem fit) using the sawhorses.

lPut The Bottom Piece In Position

• Fit the bottom piece into door frame using a level

• Hit nails partway into each jamb

• Bend the nails slight to secure their position.

• Assemble the vertical, curved and horizontal pieces of the track using the manufacturer’s instruction

lFit The Remaining Panels

• Put the second panel on the first panel

• Use a hammer to hit nails into it

• Fit the hinges.

• Repeat the process for the number of panels required and achor individual piece into the door jamb.

lInstall Rollers

• Fit the rollers in the section’s supports

• Put the rollers in the assembled track and make sure they’re not pressed to tightly against the track to prevent friction.

lSecure Tracks & Fit The Springs

• Fit the curved and horizontal pieces

• Assemble the springs following the manufacturer’s instructions

• Ensure that the tracks are level and parallel by lifting the door to about half length

• Lift the door to cover the distance left and fit the springs to the pulley system

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

Residential architects can help make sure that your building or extension is designed beautifully. They may also be able to develop plans which create extra space, or add more functionality. In addition, having plans may speed up the building process and reduces the chance of errors.

After making the decision to refurbish your home or property, the next obvious step is finding the right builder to get the job done. The process of getting a good and reliable builder can be a very tricky one especially when you don’t plan ahead. And in truth, the outcome of your house refurbishment project can only be as good as the contractor your hire. Consequently, finding the perfect builder for your task should be a top priority to get the best return on investment. Here are a few sources that will put you in the right direction to finding a reliable home refurbishment company.

✓ Friends, Relatives & Neighbours

If you have a friend, relative or neighbour that have recently completed a home refurbishment project, you can go for a visit to check out the work done. If you’re pleased with the work, you can proceed to ask about the work ethics of the builder and get the contact if satisfied.

✓ Internet

With the rapid rise of online technology, there’s hardly a service you can’t find on the internet. Websites like HomeAdvisor have been helping people find their desired service providers with relative ease for so long. To get the right building contractor online, it’s advisable to check reviews as well as testimonials before moving forward. Nowadays, you’re most likely going to find so many positive online reviews as some businesses now go to the extent of dubiously writing good reviews for their companies. As a result, it’s recommended to pay closer attention to the negative reviews and check if it’s something you can cope with before hiring a contractor.

✓ Store Contact Lists

You’ll discover a long list of building contractors on several stores trading building materials. These builders may not be affiliated with the store owners, but many stores see it as their responsibility to point you in the right direction so that the building materials acquired from them can be put to good use.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.