Find a Shop Fitter you can trust in Walton-on-thames.

Conservatories and orangeries look very similar, so it can be hard to tell what their differences are. The main thing that distinguishes the two is the amount of glazing they have.

Conservatories usually have a roof that is made up of at least 75% glass. Orangeries, on the other hand, have roofs that are generally less than 75% glass.

Conservatories also tend to have walls that are made up of at least 50% glass. However, orangeries have glass on less than 50% of the wall area.

Orangeries were originally developed to grow oranges in large stately homes. Their mixture of brick and glazing gave the oranges a combination of plenty of sunlight and shelter.

A pitched roof is a type of roof that is defined to have a sloping surface that has an angle that is greater than 20 degrees. Pitched roofs offer a more classical appearance. They remain the most communal and effective answer in wet and cold weathers to guarantee all-out protection.

Eaves

In the roof, the lower part of the inclined roof which is prominent outside the external face of the wall. The chief purpose of eaves is to pour the rainwater from the roof straight on the exterior wall. It also provides protection from sunlight. Eaves are sometimes decorated to an architectural beauty.

Gable

The Three-sided higher part of the wall at the end of a ridge roof.

Flashing

A band of impermeable material, typically metal, used to eliminate water from the intersection between a roof covering and another part of the structure. Flashings are provided to stop moisture from inflowing the wall and roof through joints in copings, parapet wall, and other infiltrations through the roof plane.

Hip

The Hip is defined as the exterior angle, which is generally greater than 180 degrees, which is formed at the inclined ridge of the roof slopes.

Ridge

The ridge is defined as the horizontal intersection made by the rising roof surfaces that are inclined in opposite directions.

Purlins

Purlins are the horizontal members which are laid on the principal rafters which help to support the common rafter of a roof. This is usually done when the span is large. Purlins are made from wood or steel. The top surfaces of the purlins intend to be unvarying and plane.

Fascia

This is the wooden board that is fixed to the feet of the common rafter at eaves. The Fascia helps the lowest ends of the roof covering material to rest on it.

Rafter

One of the major structural components of a pitched roof is a rafter. The rafter generally begins for the support of the roof to the ridge or hip. The purlin is supported by equally spaced rafters used side by side.

It’s up to you what size gravel you use for your driveway, but there are some guidelines that are worth following. If you go too small, your gravel will get displaced easily. But, if you go too big, you driveway might be quite tricky to walk on. Generally, it’s a good idea to go for a gravel size somewhere between 10-20mm.

In a server room, you have multiple electronics in a single room. If you stand a bit close to your personal computer while its still running, you know you’ll definitely feel some heat. Now imagine the amount of heat that would be generated by large servers in a single room (hint: it’s quite much). A server room would be highly uncomfortable to work in with that amount of heat around and beyond that, the heat is also very dangerous to the electronics. It can lead to equipment malfunction or even breakdown. When the equipment in your server room is one that stores all your business’ information, then it’s simply a no-brainer to do everything you possibly can to protect the equipment. Hence, the reason why every server room requires a good and well installed air conditioning system which helps to control temperature as well as moisture in the server room. It also goes a long way to control the amount of dust in the room and dust can also affect the performance of the electronics. Here are some of the reasons why the HVAC system in your server room should be professionally installed.

• The quality is guaranteed. Compared to when the installation project is made a DIY task, a professional installer is able to guarantee a better quality result. They possess the necessary experience, knowledge, tools and skills to make the project a successful one and highly satisfactory.
• They offer technical advice. When you hire a professional HVAC system installer, you also get free advice on a bunch of relevant technical topics and lots more.
• They often offer maintenance guides and after installation support. Companies that are committed to customer service and utmost satisfaction will often provide maintenance guides and technical support post installation. They also give you the opportunity to leave a feedback based on your experience so they can improve on their service delivery.

Can You Plaster Over Artex?

The short and simple answer to this question is yes, you can plaster over Artex. However, you must also note that plastering over Artex may not be the best choice as Artex is porous and as such, you’d have to detach the stripping so as to get a smooth and even coating. In the event whereby your ceilings or walls have Artex on them, you’ll have to smooth the Artex in order to obtain a plaster of solid coat.

✓ Preparing Artex for plastering. First and foremost, you’ll have to detach any bumps before you can plaster over the Artex. Do note that you don’t have to completely remove the Artex, all that’s needed is just enough to get a coat of plaster. Make use of a scraper to get rid of the bumps on various Artex designs like swirl and bark. Once you’re through getting rid of as much bumps as possible, there’s the need to seal the Artex due to the fact that it can absorb the moisture out of the plaster which will cut the time to get a good finish to little or nothing. You can use a PVA and water mix to do the job!

✓ The PVA mix. This is done to seal off the porous Artex in order to stop it from absorbing moisture from your plaster which can make it start to crack and crumble. To do this, simply mix half PVA and half water, then use a brush to paint the mixture over the plastering area. Once done, you can give the plastering surface about two to three coats and wait for the solution to dry off within a hour or two.

Plastering over Artex is not as hard as it seems, but if you lack the confidence to complete the task, simply contact a professional for help.

A tiled floor perfectly blends style with function, be it a sophisticated matte finish or a gleaming glossy sheen. Moisture and stain resistant, floor tiles represent a practical choice for a busy home and its elegance makes it even more suitable irrespective of the interior design project. What’s more? Floor tiles are generally cost effective and requires low maintenance, however, this doesn’t mean you should not show your tiled floor some love and care from time to time. If you’re wondering how to go about the maintenance of your tiled floor, then you’ve come to the right place. In this post, we’re going to share with you some maintenance tips to take care of your floor tiles. Let’s take a look!

• Get rid of excessive dirt on a regular basis. From mere food stains to more serious scratches, a busy domestic life can significantly shorten the lifespan of your tiled floor if care is not taken. While being easy to clean makes the maintenance quite simple, regular upkeep of the floor is quite important as loose dirt and debris can wear away your flooring’s finish over time.
• Do not ignore the grout. While the surface is stain and moisture resistant, same thing cannot be said of the grout. To keep the gout lines clean, simply make use of a soft bristle brush or a white pencil eraser.
• Try out deep cleaning your flooring. Although regular maintenance of your flooring is essential to have your floor looking clean and neat, deep cleaning is just as important to preserve the overall finish of the  floor.

While some people may see bifold doors as insecure, many bifold doors feature advanced security measures. Internally beaded strengthened double glazing is very secure. Choose a bifold door with a multi-point locking system for enhanced security. If your house is empty for long periods, always consider a blind solution to keep prying eyes out of your home.

When it comes to the electric vehicles world, one of the most common questions that’s usually asked is - how to charge my electric car? If you’ve carried out some research, you’d would have seen terms like level 1, level 2 or level 3 being thrown around. In this post, we’re going to consider the meaning of an ev fast charger to give you more insight into the electric vehicles world. Let’s take a look!

As the name suggests, fast charger is an electric vehicle charger that’s a lot faster than the average ev charger. These incredibly powerful units can have your vehicle charged to 80 percent within an hour depending on the model and capacity of your car while also being highly convenient for those who are always on the go. So what’s the difference between rapid and fast car chargers?

Generally, fast car chargers are available in two varieties which includes - the 7kW which is the most popular option used in homes, or 22kW which is commonly used in supermarkets as well as shopping centres. While 7kW takes up within 4 - 6 hours to charge an ev battery to 100 percent, 22kW will take about 1 - 2 hours to do the same. Most fast devices will be AC, there are also some DC ones available as well. What’s more? A large majority of fast car chargers are untethered. This implies that the cable isn’t connected to the device allowing you to make use of your own. This can, at times, make it a lot more convenient than rapid chargers which makes use of tethered cables.