Find a Shop Fitter you can trust in Windlesham.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

Who Fixes Boilers?

With boiler running for several hours in a day and working hard to ensure that our home stays warm, even when we tend to take it for granted it’s always there give us the heat we need whenever we need it. So in the event whereby the inevitable happens and your boiler breakdown, which professional is the most suitable to call for help? When the pressure is on to stop a boiler leak or bring back warmth to your home, knowing who to call can make all the difference.

When you need a professional to fix your boiler, the right professional to call is a heating engineer. Heating engineers work mainly on heating I both homes and businesses, so you’d be right to call them specialists in all heating matters. As a result of this, you may want to give them a call when experiencing some issues with your boiler as they’d be in the best position than any other professional to give you a proper solution.

Generally, heating engineers are experts when it comes to fixing boilers and can help with various tasks such as installing a new boiler, boiler repairs, installing new gas pipes, repairing gas leaks, changing radiators, fixing leaks, installing heating controls and many more. What’s more? A boiler repair has to do with working with gas and before you can do that you must be a Gas Safe registered engineer as required by the legislations in the UK. In other words, any gas boiler related issue must be tackled by a Gas Safe registered engineer as this is a very dangerous fuel in which the services must be provided to highest standards of safety. Only heating engineers can be a Gas Safe registered engineer to work on gas boilers.

How Much Does A Handyman Charge Per Hour?

Do you need the professional services of a handyman? If yes, then you’d probably like to know the hourly rate a handyman charges in order to set a budget and make the necessary plans. Here, we’ll discuss the amount charged by handymen per hour and reason for the differences.

The fact is, there’s no accurate or single answer for all handymen as the project varies and the handyman mostly charges based on the type of work to be done. However, there are also other handyman pricing strategies which includes project pricing. When you’re being charged based on the tasks involved, you should ensure to ask the handyman for possible discount as several handymen will offer a considerable discount for bulk projects or tasks that can be completed on after the other. If the task is a small, one-off job then you’re likely to pay a minimum charge fee which would usually be higher when compared to the task being part of a larger project. Consequently, the first one hour of a handyman’s service will usually attract a premium, while the charges for remaining hours after the first will be a smaller charge. This is mainly due to the fact that a handyman will need to travel to deliver a service and it’s generally going to be a lot more economical to arrive on the site and take on a couple of tasks sequentially.

Moving forward, you should be aware that there’s an economy in sticking to one handyman. Handymen usually charge less to repay clients for their loyalty as they’d already have an idea of the client’s projects and needs which makes the job a lot easier. However, generally a handyman will charge within the range of £20 to £30 per hour.

How Much Plasterboard Do I Need?

Although many people especially contractors have a tough time estimating the number of drywall or plasterboard needed to complete a project, it’s a rather simple task if all factors are taken into consideration. If you’re able to follow the same procedures taken by professionals to count dry wall sheets, you’ll be in the right direction. Let’s have a look at the procedures to follow!

lTake Square Footage Measurement

• Measure the square footage of the area where the plasterboard will be fitted.

• Multiply the height by the width of each wall or ceiling area.

• Add all quantities to obtain a total square-foot amount.

lCalculate Drywall Sheets

• To calculate the number of drywall or plasterboard sheet is very simple once you’ve gotten the total square footage.

• To get started, simply divide the total square footage of area by 32 (that’s if you are using a 4 by 8 sheets) or you can also make use of 48 to make the division (only if you’re making use of the 4 by 12 sheets).

• The answer you get after the division will give you the full number of plasterboard sheets that’s required to complete the project.

We’d recommend you include an extra 10 to 15 percent of whatever you calculate to take care of the possible odd cuts and wastages. This implies that if your total area is 1600 square feet while incorporating 4 by 8 sheets, simply divide 1600 by 32 which equals 50 sheets, now take 10% of 50 which equals 5, then add back the 5 extra to the 50 sheets earlier calculated to get 55 sheets. If you wish to estimate the cost, simply multiply the number of sheets gotten by the price per sheet. Do not forget to include delivery charges and local taxes.

How To Clean A Roof?

If you’re planning to clean your roof, but don’t know where to start, you’ve come to the right place! There are different types of roofs available in the market today and the method used in cleaning one can be largely different from the other. As a result, we’re only going to look at one of the common types of roofs you’ll find in the UK - the Asphalt shingle roof tiles. This roof type is very common and for a good reason. Not only are they visually appealing but they’re also hugely versatile by design which enables them to be adaptable to varying shapes, angles as well as forms depending on your preference or needs. With all the benefits that can be derived from asphalt shingle, they however, need to be properly maintained to help retain their good looks.

To clean your asphalt shingles, you’ll most likely require some type of chemicals especially when dealing with algae stains and some other visual problems. Therefore, make sure you purchase a product marked safe to be used on this type of roof and not those only proven to remove moss and algae stains. Mix the chemical cleaner with a gallon of water and a quart of bleach or as instructed by the manufacturer. Pour the mixture inside a pump-style garden sprayer and mix thoroughly. When done, climb up on the roof and spray as good as you can. Upon completion of spraying the roof with the mixture, then allow to work its magic for some time - about 15 minutes or thereabout should be good.

After that, you can make use of a garden hose to spray down the roof and wash down the mixture entirely. If some stains remain, use a brush to gently wipe the tiles individually.

Sewer is simply a set of pipes or drains that’s usually underground and whose primary function is to remove waste water as well as other waste materials. Generally, there are three main types of modern sewer systems and they include sanitary sewers ( also commonly referred to as foul sewers), storm sewers or surface water sewers as well as combined sewers. Now let’s take a look at each of the sewer types!

• Sanitary sewers or foul sewers. These are the sewer systems that are mainly incorporated to transport waste water and other waste matter from both homes and businesses to waste water treatment plants. Normally, they include pipes, manholes as well as pumping stations. Their function is, however, not only to carry waste water to treatment plants, but also to maintain the water quality as this is essential for public health. Here, gravity is commonly used to remove the waste water. However, in low lying areas, pumps can be incorporated especially when the waste water needs to reach an area that’s at a higher elevation
• Storm sewers or surface water sewers. The primary function of this sewer system is to carry rain water as well as melting snow ( unlike sanitary sewers that are designed to carry waste water) from the roofs and roads and then direct it straight into the streams, rivers and also other water bodies. These sewer systems can get clogged with leaves, litter and other debris which can ultimately lead to flooding.
• Combined sewer. As the name suggests, these sewers are combined. This implies that the make use of a single pipe to carry both waste water and storm runoff water to wastewater treatment plants. These aren’t very common anymore as the sewer can overflow especially when there’s a lot of rain which makes the system incapable to handling both the waste water and surface water.

Plastering is suitable to cover most Artex. If it’s shallow Artex, it may be covered by skimming plaster on top. If the pattern of the Artex is too deep, you may need to use plasterboard to cover it or if you want to remove it entirely, you will need to use a wallpaper steamer.