Find a Shop Fitter you can trust in Swansea.

If you’re replacing your carpet with new carpet, you might be able to use your old underlay. This is dependant on how long the existing carpet has been down for and also the condition of the underlay. But if you’re getting wood, laminate or vinyl flooring it’s not suitable. It will put stress on the joints if you use underlay.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

How Much Is A Conservatory Roof?

If you’re setting a budget for your new conservatory structure or perhaps you already have one and thinking about replacing the roof, knowing how much a new conservatory roof will cost from the onset can save you a lot of headache. However, knowing the correct cost won’t be easy as this is determined by a plethora of factors which is unique to each individual. In this article, we’re going to give a rough estimate of a conservatory roof cost so as to help you make an informed decision moving forward. Let’s have a look!

In order to determine the cost of your conservatory roof, the type of roof you go for must firstly be determined. This is because there is a wide array of conservatory roof types with each having its own unique price. You can opt for the uPVC glass roof, a tiled roof or a glass roof.

With so many other factors to consider, we’ll not be able to give you an exact amount. However, in general, a conservatory roof can cost anywhere within the range of £2500 to £8500. You may also quoted for more or less depending on your roof type as well as the specifications you opt for including the size and type of your conservatory. For instance, if you own a Lean-To conservatory with a size of 3.1m by 3.1m, for a glass conservatory roof, you can expect to spend anywhere within the range of £3000 to £3500. Meanwhile for a Victorian conservatory roof with a size of 5.1m by 5.1m, the cost will range between £5000 to £8000.

Therefore the type as well as size of your conservatory really does greatly impacts the cost of your conservatory roof.

How to build a scaffolding tower?

Scaffolding is every so often an essential portion of construction and home maintenance. You must set up scaffolding properly to make sure you and anybody else using the equipment stays safe. A mistake in establishing a scaffolding could lead to a serious accident. Scaffolding is an alternative to ladders. An advantage of using scaffolding is the bigger work range and flexibility it offers over that of a ladder. It possesses a stage for walking and for keeping all your tools.

The steps to build a good scaffolding

You will first need to find a secure and stable foundation on which you will build and put op the scaffold. Next, you will need base plates that will help to make the footing of the scaffold more stable. One of the chief worries here is to have the scaffolding equal and on safe ground.

Opt for casters.

If your project involves moving your scaffolding to work on several spots, include casters in your scaffolding setup. Do not forget to lock the casters after you get it in place.

Assemble the scaffolding frame.

Lay out the ends of the scaffolding. First, you will need to lift one of the end pieces and attach it with the upper cross brace. While you are lifting the second end piece to attach it to its upper cross brace, the far end of the previous brace should support it.

Make sure the scaffold is stable.

Move the scaffold until you think that the position is perfect, and make sure it is level and secure.

Place the planks.

Lift the boards through the scaffold bars and into the right place.

Secure access to the scaffold.

If you are using ladders to access the scaffold, use the ones that are designed specifically for that very type of scaffold.

Attach the guardrails.

Attaching guardrails is highly advised due to the risks of falling. You should also consider using tie-offs and other means of fall protection.

Inspect the scaffolding to ensure safety.

Thoroughly examine the scaffolding set up to make sure all pieces are secure.

Not if you don’t want to! The size of many appliances is standardised, meaning they should fit in to any new kitchen. Ask an experienced kitchen designer or installer if you’re not sure if your current appliances will fit into a new kitchen, and of course, new cupboards and worktops can be fitted around your existing appliances if you are keep them!

How To Remove Tile From Wall

Have you stumbled on some stylish new tiles you wish to install in your home, be it bathroom, kitchen or living room? Or perhaps you just feel your old tiles have outstayed their welcome and need a to install a more modern and appealing wall tile. The first step before installation of the new tiles will be to remove the old ones which can be done by following these simple steps below:

lSafety

• To remove wall tiles, you’d have to chip them away and that implies shards of porcelain, ceramic or glass flying around. Hence, your safety should be a top priority.

• Use safety goggles and protective gloves to protect both your eyes and hands.

lCover Up

• With several sharp objects flying everywhere, all objects in the room are far from safe.

• Use a cardboard or old sheet to protect the room and valuable objects from damage.

lAssemble The Tools

• For wall tiles removal, you need just two tools - a hammer and a chisel that’s a bit thin.

• In the event whereby a chisel is not available, you can make use of a flat headed and large screwdriver.

lGet To Work

• Feel for a loose tile to start with and if successful, chip it out with a chisel.

• If you can’t find a loose tile, then break one by sticking the centre of a tile with a chisel and hit it hard with a hammer.

lRemove All Tiles

• Once you’ve been able to chip away or break the first tile, you can easily get access to other tiles.

lClean Up

• Try to get as much dried adhesive off the wall as you can by gently tapping it with the chisel and hammer so as not to damage the wall.

• Once done, put away the cardboard and dust sheet which should have collected much debris.

• Use a brush and dust pan to clean out the loose pieces (if any).

Wall tiles removal can be a very dangerous process which should be left to a professional especially if you lack a proper training or experience. This is not only to prevent anybody being hurt, but also to avoid any possible damages to the wall or any valuable object which can result in additional cost on repair or replacement.

Some paving projects require you to cut paving slabs to make them fit into a smaller space. To do this, firstly you need to measure the slab and draw a line in pencil or chalk where you want to cut.

There are then several different ways you can cut the slab – you or your professional can choose the one you or they are most happy with. A hammer and chisel can work well, or a handheld saw. You can also use an angle grinder fitted with a stone-cutting disc.

Fascias and Soffits, just like any other components of a home, do not last forever. They can become tired and worn out over time which implies that you’ll have to replace them to prevent further damage. Getting this project completed can be quite costly, but it doesn’t have to be. Fitting soffits and fascias is very simple task which will leave you with both a modern and contemporary styling which requires little maintenance and also more savings. What’s more? You don’t have to worry about repainting the fascias and soffits on an annual basis, all you need to do is a gentle wipe down of the features with a damp cloth to have them look good.

If you’re a competent DIYer and confident enough to pull off this task, then all the better. However, if otherwise, we’d strongly recommend you hire the services of a reliable contractor who can guarantee the best results for help. Here are the steps you can follow to fit your fascias and soffits.

Fascias ( a 18mm fascia board)

✓ This is designed for a direct fix without a need for a timber substrate. Simply secure them directly to the rafters with the help of 2 x 65mm a4 stainless steel fixing nails per rafter.

✓ Ensure that the rafters are level.

✓ Cut the boards back 5mm per edge to enable expansion where any white corner trims, joint trims or angle trims is needed.

✓ Secure the guttering to all third rafter.

Soffit ( 9mm soffit board)

✓ Ensure that the preservative treatment to the structural timber has dried out.

✓ Fix all utility boards of about 100mm to 605mm in width at a maximum of 60mm centres.

✓ If ventilation is needed, there are some soffits that are available in 150mm to 605mm widths and also provides the 10mm air gap needed for roof with a pitch above 15 degrees