Find a Shop Fitter you can trust in Kingswinford.

Fibreglass, or GRP, flat roofs are very durable and should last you years, but over time they can become brittle and you might see some cracks or holes forming. Luckily, you can repair a fibreglass flat roof and it doesn’t have to be too difficult. Cracks in a fibreglass flat roof If you notice long cracks in your fibreglass roof, you can often use a fibreglass crack sealant. Simply clean the area, squeeze the sealant into the crack, then smooth it off. If you want it to look neater, you could coat the entire roof with a restorative coating which will make it look new again. Hole in a fibreglass roof If you notice a hole in your fibreglass flat roof, you’ll want to get this repaired as soon as possible to avoid any rainwater getting into your home. There are lots of fibreglass roof hole repair kits on the market, both online and in DIY stores, so you shouldn’t have trouble picking one up. They usually contain a mouldable UV cured patch that you can stick onto the hole. It will harden and become instantly weatherproof, so is the perfect emergency repair solution. Fixing pin holes in a fibreglass flat roof Unfortunately, if you find pin holes in a fibreglass flat roof it’s often because the installer didn’t use enough resin during the fibreglassing process. Luckily, if you can’t get back in touch with the installer or you only notice after a few years, you can fix this yourself. Sand down the roof back to the clear resin layer. Clean the entire roof with acetone and reapply some GRP roofing resin. Ensure that all the pinholes are filled – you might need two coats.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

Gravel, asphalt, concrete and paving can all be permeable. However, some types of asphalt and concrete are impermeable. This is why it’s important to be precise about what material you want for your driveway. If you want a permeable driveway, you should also make sure that your sub-base is also permeable.

Do Bifold Doors Fold Back Flat?

Bifold doors, also referred to as folding doors, have grown to become a great alternative to the conventional sliding doors. It has become a necessity rather than a luxury for most home and property owners especially in the south east who are in need of more space and a memorable focal point. However, before installing the impressive bifold doors in your home’s doorways, it’s always a wise decision to learn more about bifold doors. In this article, we’ll let you whether or not bifold doors fold back flat.

Generally, bifold doors consists of 3 to 8 door panels, bifold slides and fold back against one another in such a way that they sit flat against one or both walls. However, this depends on how they’re designed, whether they’ve been designed to open either from the side or from the middle. They basically work on what’s popularly referred to as a concertina principle. This style fold principle works in a way that allows the door panels to smoothly fold back flat which totally opens up the room into an open plan masterpiece.

So now that you know that bifold doors fold back flat, you may also be curious to know whether they also open in or out. Depending on your specific requirements, bifold doors can actually open inwards and outwards independently. However, due to the fact that opening bifold doors can take up some essential space, several home and property owners do prefer installing their bifold doors in such a way that allows it to be opened outwards. What’s more? It’s also essential to take into account that opening bifold doors inwards have the potential to drip water onto internal flooring especially for the wet regions.

How To Paint A Radiator

First thing you should know about painting a radiator is that normal paints can’t be used to do the job, however that doesn’t mean it’s not cheap, easy and fun - it definitely is and even more so, when you do it the right way. With a few radiator painting hints here, it’s only a matter of time before you start painting your radiators every colour of the rainbow delightfully.

Painting a radiator is not one of the most common tasks on most people’s to do list, so we’ve created this article as an encouraging nudge to allow more people let their creativity manifest through a brush. However, this is not to say that this is a task for everyone though as you won’t like to make a mess of your radiator. If you know you can’t pick up a brush or bend a knee or your back here and there, then you probably shouldn’t. In such cases, hiring a professional painter would be your best bet to get the best results while also saving yourself some time and money.

To paint a radiator, you’ll need a paint brush, suitable radiator paint, dust sheet and a radiator paint brush (optional).

✓ Turn off the radiator and leave it to cool off. Once it’s cold, simply wipe out all dust, dirt or grease from the radiator.

✓ Protect the flooring under the radiator from any paint splatter with a by spreading out a dust cloth.

✓ Use a suitable radiator paint to brush out well and lay off evenly in a direction. Leave it to dry overnight. Then apply paint on the radiator in direction of the grooves with the help of a top quality brush.

✓ Paint in sections and move across the radiator slightly overlapping until you get to the end. The move to paint the other areas.

✓ Leave the paint to dry as instructed in the manufacturer’s instructions, then apply a second coat if necessary.

Velux installers offer the Velux Active home kit. This provides an automated system to enhance your indoor living. With its sensor-based ventilation apparatus, the Velux active home kit’s smart sensors repeatedly monitor your home’s temperature, humidity and CO2 levels for its optimum healthy living standards.

Sensor-based ventilation
Velux Active tracks temperature, humidity and CO2-levels, and ventilates to keep your indoor climate nice and healthy.

Automatic heat protection
Velux Active automatically protects your home from excessive heat by closing your Velux Integra blinds, awnings and shutters on hot days.

Set personal preferences
Want to swap your alarm clock for a sunrise or air out while you’re at work? Customise your indoor climate with Velux Active.

Voice-control and smart speaker integration come standard with VELUX ACTIVE with NETATMO, enabling you to draw the shades or open the windows just by asking.

Every year, various parts of your roof may need to be changed at one point or the other. Due to the fact that this event can occur at any time in a year, there’s the need to be fully ready. When it comes that being ready, you simply can’t overlook the importance of soffit and fascia boards in protecting your roof space and helping it maintain its clean and unique visual appeal. As a result, when your soffit and fascia boards need to be changed, you best do so as quickly as possible.

This task can be completed by anyone with basic DIY knowledge and experience, but if you lack the confidence to pull off then it’ll be advisable to hire a professional who can guarantee the best results for help.

✓ Remove the old existing boards. In order to install the new soffit and fascia boards, you’d have to remove the existing ones first. If necessary, you can make use of a Stanley knife to make the process much easier.

✓ Fixing soffit boards. Several soffit boards are made using uPVC. The boards are to fixed to the underside of your timber rafter ends. Make sure to use timber to close any gaps between soffit boards and also make sure that your soffit boards’ back are resting against the wall’s top.

✓ Fixing fascia boards. Many fascia boards are also made from uPVC and are usually installed in a similar way to soffit boards. Use a minimum of two nails to make sure they’re secure enough to hold weight of any roof tiles and also to prevent any buckling.

✓ Guttering and felt. To start the guttering, you’d have to screw any brackets into the facia board. You can use a spirit levelto make sure the alignment is perfect to enable the floe of water directly through your guttering system. Once done, you should also check for any rotting roof felt at the edges closest to the gutterin. If there is a rot, make use of eaves felt trays and tuck under existing felt and overlap into the guttering