Find a Shop Fitter you can trust in West Bromwich.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

If you’re looking to have your boiler insured, there are a number of boiler cover providers you should probably check out with British Gas Homecare being right up there as one of the best in the business. In this post, we’re going to consider the British Gas Homecare prices to help you make the best-informed decisions possible moving forward. Let’s take a look!

Firstly, British Gas offers a wide variety of packages to provide coverage for repairs as well as breakdowns on heating systems. They also offer plans which includes cover for your central heating, plumbing, drains as well as electrics. With this provider, you can choose to pay your cover either in monthly instalments or annually. Simply have it at the back of your mind that the cost of your package will depend mainly on the things you want to cover – the more the risk you wish to protect against, the more expensive your package is likely to be.

In general, HomeCare starts from £13 a month (£60 excess). Conditions and exclusions is applicable, prices may also vary based on your property’s postcode. With British Gas, there are a number of products to select from within their range some of which features an annual service and repair of your boiler and controls. Their products include British Gas Home Care One, British Gas Home Care Two, British Gas HomeCare Three and British Gas HomeCare Four. There are also some exclusions, which means that irrespective of the HomeCare product you opt for, there are certain things that British Gas do not cover. For instance, sludge or scale removal and the repair of the damage arising as a result. Showers and their parts, shared drains, faults caused by a non-British Gas engineer and more.

Overall, the amount you pay per month or year will be based on your location in the UK and the British Gas will confirm the price once they’ve been able to take a couple of details from you.

Network enabled/IP cameras are digital CCTV cameras. With these cameras, the video captured can be streamed over the internet anywhere in the world. Most manufacturers of IP cameras have a smartphone app that allows you to watch the video feed on your phone.

Do you think your outside drain is blocked? If yes, then you should have it treated as soon as possible and most especially by a professional who can guarantee the best outcome. When you fail to unblock your drain when due, there is no limit to the damage that can be caused. These includes water leakages which can damage your home or business facility. And in critical situations, it can as well result in pipe burst which will definitely cost you a lot more money to fix when compared to taking a quick action to unclog the outside drain blockages. If you’re thinking about hiring a professional, then you’d probably want to know how much its going to cost. In this post, we’re going to look at the cost of clearing an outside drain and the possible influencing factors.

The cost of clearing an outside drain is based on a number of factors. These factors include the type of the blockage, the method used, the location of the property as well as the ease of access. Using the blockage type as an example, a small blockage in a toilet or sink is usually priced within the range of £50 to about £70. However, for an extensive blockage deep in your outside drain that’s hard to access, you may end up incurring anything within the range of £150 to about £200.

There are also a wide variety of methods that can be used to clear blockages from an outside drain which will also play a key role in the final cost of the service. These methods include drain jetting which usually costs within the range of £70 to £175, drain rodding from £80 to about £145 as well as a full system scrub which should cost about £150 to £200.

It is, however, important to note that the above costs are just an estimate and other factors as mentioned earlier on will also have an influence on the final price.

Some properties are unable to have double glazing, especially those in conservation areas or listed buildings. To counter this problem and still benefit from a warmer home and cheaper bills, secondary glazing is an option. Secondary glazing is a second pane fitted inside your original window. Secondary glazing will still save you around £105 yearly.

With your finger probably hovering round the ‘order now’ button, one thing often comes to mind, what size of skip do you actually need? Being fully aware that there’s a huge array of skips sizes and hiring the appropriate size can make a whole world of difference when it comes to cost, efforts must be made to ensure you determine the right skip size before clicking on that ‘order now’ button.

To give you a better idea of skip sizes and the type of project that they are best suited to, we have decided to provide this simple breakdown that’ll make your decision process a breeze - quick and easy.

• 4 Yard Skips ( 3 cubic metres )

The 4 yard skip is best suited to small domestic projects like home or garden clean or clear outs, bathroom or kitchen refurbishments and the likes, due to its relatively small size. It has a capacity to carry about 30 bin bags at a go.

• 6 Yard Skips ( 6.5 cubic metres)

Do you want a skip for domestic purposes or for small commercial projects?if yes, then you should definitely give the 6 yard skip a shot. It has a capacity to hold up to 60 bin bags.

• 8 Yard Skips ( 6 cubic metres)

This skip size is best suited to large domestic tasks or light commercial projects. It has a capacity to hold up to 60 to 80 bags effortlessly.

• 10 Yard Skips ( 7.65 cubic metres)

With a skip size this big, both large residential and commercial projects can be handled with relative ease. Not only does it have the capacity to hold up to 80 to 100 bin bags, but also comes with an enclosed lid option, if you need an extra security for your property.

• 12 Yard Skips ( 9.18 cubic metres)

This skip size is best suited to both large residential projects and building sites. It has a capacity to hold up to 100 to 120 bin bags, and just like the 10 yard skips, it comes with an enclosed lid option for an extra security.

Click here to learn more about skips

There are a wide array of smart ring doorbells available in the market today and all coming with detailed installation instructions. Here, we’ll make it clearer to enable you get it done right, the right time and with little stress. With a properly installed ring video doorbell, you’ll be able to identify who’s at the door before opening and even chat with them via your table, PC or Smartphone. And to make it even more interesting, you can easily install a ring doorbell yourself and save some money.

Installation Steps

• Assemble the mounting bracket

Bring out the mounting bracket that comes with your ring video doorbell. You’ll discover a small level within the mounting bracket, put this on the bracket’s slot. Once done, gently line it up to the spot where you want to place your doorbell.

• Determine the pilot holes

Firstly, ensure the bubble found in the level is straight. Then, mark out where the screws will go through.

• Drill the identified pilot hole spots

When drilling, you’ll need not just your drill and drill bit (or a masonry bit, if its a brick), but also your eye and ear protection. Drill the marked out spots to create pilot holes and subsequently hammer in the plastic anchors that comes in the ring doorbell’s pack to help hold your screws in place. Once done, put the bracket on the top and tighten your screws.

• Scan the QR Code

With the use of your phone, scan the special QR code given behind your doorbell to ensure the ring doorbell is only accessible by you and your loved ones.

• Secure the doorbell

Ensure that the bracket is properly in place and attach your doorbell to the mounting bracket. Once done, you can make it safe by using smaller security screws to hold it. Upon completion, your ring doorbell is ready for use - it’s that easy!