Find a Shop Fitter you can trust in Batley.

The roof is a particularly important part of the home, providing weather and water protection. Therefore, it’s important to regularly check your guttering system and clean out any debris that could cause blockages.Advice given is to consider having a mesh gutter guard to prevent the build-up of leaves and other debris, especially if you want to harvest rainwater.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

The short and simple answer to this question is yes, it definitely does matter if the graffiti has been there a long time! When it comes to graffiti removal, one thing to have at the back of your mind is prompt removal is always the most effective. However, this doesn’t mean that a long existing graffiti can’t be removed. Graffiti that has been in existence a long time can be removed, but you shouldn’t expect this to be a walk in the park. If you don’t have the experience, tools and skills to pull this off, it’s strongly recommended that you call in a qualified professional for help so as to ensure the best result is achieved without any form of damage to your walls.  However, if you wish to give this a shot, then here are some tips that should put you in the right direction.

Here, we’ll advise you to get an effective graffiti cleaning solution such as Elephant Snot® to remove the long existing graffiti. To start the removal process, simply brush the product ( Elephant Snot® ) with the help of a wallpaper brush on the affected wall. Once completed, let the product sit for about 45 minutes to 1 hour to make for an easy removal. After this, you can then proceed to power washing it off at about 1400 to 1600 psi cold water. This should remove virtually all the paint leaving only a few behind. Identify the remaining stubborn graffiti and go for a second application. Repeat the process until the graffiti has been fully washed off. This should leave no damage to your wall whether brick or mortar.

How To Draw A Garden Landscaping Plan

Are you thinking about constructing a new garden landscape? Do you have an existing one but forgot where you planted those tulip bulbs the previous autumn? Or perhaps you’re just trying to identify the exact spot where you cut back that clump of wilted foxglove, without mistakenly digging it up. For everything to be much easier when it comes to a garden landscape, it’s always a wise decision to draw a garden landscaping plan.

To get started, let’s take a look at the materials you’ll need to acquire. These includes a piece of white paper on which the existing elements on your garden will be plotted, a piece of tracing paper and tape to give options for planned additions, a pencil, an eraser as well as a measuring tape.

For more accuracy while drawing your plan, you’ll need to measure the garden’s distances, perimeter, the existing garden beds size as well as the trees’ and shrubs’ shape and size.

• Write down the measurements taken on the scrap paper.

• Assuming it’s a medium sized backyard garden that’s 18 feet wide, we allocated a scale of 3 feet to equal an inch.

• Using a piece of white paper (could be graph if you wish) and a pencil, carefully outline the perimeter of the space. Once done, you can then sketch in the existing plants as well as other special features on the space (features that are of a permanent nature like trees, fences and paths).

• Hold a piece of tracing paper and tape in on top. Then you can sketch out the plants you wish to add to fill in the spaces in the garden on the tracing paper.

If you’re looking to purchase and install a solar system for your home or property, then knowing the amount of energy a solar panel can produce can go a long way to help you determine just how much solar panels that’ll be needed to power your entire house. In this article, we’ll give you an idea of the amount of energy that can be generated by a solar panel to help you make informed decisions going ahead.

First and foremost, you should note that each and every solar panel is rated by how much direct current power they’re able to generate under standard testing conditions. The output of a solar panel is given in watts units (W) and it stands for the theoretical power generation of the panel under direct sunlight as well as temperature conditions. Generally, several domestic solar panels possesses power output ratings which ranges from 250 watts to 400 watts. And as you would have expected, the higher power ratings are preferable when compared to the lower power ratings. What’s more? The total wattage of your solar panels will greatly influence a major part of your overall solar system cost.

Assuming you’re able to get just about 5 hours of direct sunlight every day, you can determine the output of your solar panel in this way - 5 hours x 290 watts ( wattage example of a premium solar panel) = 1450 watts-hours or approximately 1.5 kilowatts per hour (kWh). hence, the individual solar panel output in your array should be able to generate about 500 to 550 kWh of energy every year. This is sufficient energy to power some small appliances without problems.

Being a commonly used building material in the 1950’s to about 1990’s, asbestos is very popular back in the days and used for almost every roofing project because of it fire resistant properties. They’re mostly mixed with cement and are known to last for over 4 decades.

Due to the harmful properties found in asbestos, the material was totally banned in the UK since the year 1999. It’s found that when disturbed, asbestos releases some fibres which when inhaled can result in some deadly health conditions such as lung cancer and asbestosis, which are all fatal. These diseases are mostly not detected until several years after the first exposure to the asbestos fibres, which makes them even more deadly. Hence, it’s crucial to know how to identify asbestos roof tiles so you can have them removed by a professional immediately. In this article, we’ll show you what you can look out for to identify asbestos roof tiles. Let’s take a look!

Asbestos roof tiles are typically square shaped and they also generally possess a combination of grey and black colour. Although asbestos can feature a number of colours based on the kind of material you mix with it. In truth, asbestos can be very tricky to identify, when disturbed not only are their fibres totally invisible to the naked eye but they’re also completely odourless. This implies that you may not even be aware that you’re exposed to such harmful material for a prolonged period of time. In order to accurately identify asbestos roof tiles, the only thing you can possibly do is to call in a UKAS accredited laboratory to have them tested. This way, you’ll have a peace of mind knowing the result will point you in the right direction.

It is crucial to make the walls of your bathroom waterproof, and bathroom wall panels or bathroom cladding is not only a great way to do that, but its also the easiest way to update the look of your bathroom. When it comes to adding wall panels to your bathroom, there are a large selection of designs to choose from which means you’ll always find something that’ll suit your space. So how do you have them installed? With this brief guide, you’ll learn everything you need to know about the bathroom panels installation. Let’s have a look!

1. Get the right tools and supplies. You’ll require a handsaw, jigsaw, or circular saw, hacksaw, drill, hammer, 1200mm spirit level, sealant gun, suction cups and tape measure.
2. Prepare the bathroom. Ensure that the bathroom walls are degreased, clean and, dust and dirt free. Also make sure that its flat and even with a spirit level.
3. Make sure a fixing method is in place. If not, make use of treated battens as a fixing method. Fit all battens in such a way that’s plumb and parallel.
4. Fit the shower tray. Take a measurement of the shower tray to identify the length of the seal strips that is needed while also making room for the shower screen.
5. Add the seal strips.
6. Cut the panels to size. Mark the bathroom wall panels and cut to get the right measurement in both height and width. Also ensure to make room for pipe and shower head holes at this point.
7. Install the panels.

If you look after your air source heat pump, it can last for over 20 years. Make sure you check it every year and get a registered or qualified installer to check it every 3-5 years to prolong its life. If in doubt, check the manufacturer’s maintenance instructions.