Find a Shop Fitter you can trust in Normanton.

No, pattern imprinted concrete shouldn’t be slippery. Most good driveway installers will add a special anti-slip agent to the sealant before they brush it onto your driveway, so it will stop it from being slippery.

It’s important to ask a driveway company how they will seal your driveway when you get a quote from them. If an untrustworthy company seals your driveway badly, it can cause a thick and extremely slippery surface, so it’s vital that you ask any contractor what their procedure is before you engage them.

It’s also important to remember that pattern imprinted concrete isn’t a ‘non-slip’ surface – it’s just not slippery. You could still slip over on a concrete driveway, just like you could on tarmac or a block paved driveway. Also, once you’ve walked and driven over your driveway for a few months, its skid and slip resistance will increase as it weathers and builds up tiny specs of dirt on it. Pattern imprinted concrete is often used in high footfall areas in places like shops, fast food restaurants and theme parks, so if there was a significant slip risk these businesses wouldn’t use it.

You might think that you could ask your contractor not to seal the driveway to make it less slippery, but it could actually do the opposite. By sealing pattern imprinted concrete, it means that moss and algae is much less likely to grow, which can be extremely slippery to walk on if it’s left to its own devices. If moss does form on your driveway, the sealed surface is much easier to clean as you can simply pressure wash it away; this is not as easy to do on a non-sealed surface.

Biomass boilers can be designed to work with other kinds of heating. The most common of these is solar thermal. This is a popular renewable energy pairing. Solar thermal heating will meet your hot water needs during the summer while a biomass boiler can operate as a backup during the winter when solar thermal panels do not perform as well.

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

A French door simply means a door style which features two sections that pivots on hinges installed on the door framing’s opposite sides, which opens and closes at the centre. Glass panels are used to make each door’s section covering the middle of the door ( either individual panels that are muntins framed or a single panel of glass). When open, the whole doorway is an open space with no post at the middle. French doors are popular for a number of reasons. Not only do they bring a particular level of charm, class and elegance to your home, but also allow natural light into a room and create a wide opening unlike a sliding patio door. They’re mostly installed at the rear of a home so as to allow for a direct walkway exiting the house and straight into the garden, thereby making your garden even a lot more closer to your home.

There are 3 main types of patio doors which includes the following:

• External or French patio doors

As the name suggests, they’re the French door that leads outside mostly into the garden. Generally when opened, the two door swings outwards, but there are some that can open inwards. They mostly possess a number of large glass panels which enable natural light to brighten up your home.

• Interior

This basically means fitting double French doors between two rooms in a house. This is very similar to the external ones with two doors and also made up of glass panels.

• Sliding

They are very similar to both the external and interior designs but rather than the two doors swinging open, they slide apart to create a great amount of space to walk into the garden. This is the classic charm that sliding French doors provide.

One of the major challenges faced by double gates is wind as this is always blowing over the gates and slamming them together anytime it passes by. So how do you tackle this? Since you can do only so little about the wind, the only option you have is to enforce or secure your double gates. This is quite simple if you have the adequate knowledge and skills, if not, we’d strongly recommend calling in a professional who can guarantee the best results the first time. In this post, we’re going to take your through the processes involved in securing a double gate to ensure your project turns out a success. Let’s take a look!

1. Hammer a pipe into the ground. Since this isn’t a heavy construction work, you need not worry about water finding its way into your basement. To do this, simply open the gate and stretch it to determine how far it can go. Once done, proceed to mark the place right below the gate’s edge. This is the spot where you will hammer in the metal pipe.
2. Install the lower bracket. With the pipe in place, the next thing is to have the lower bracket installed. Start by drilling some pilot holes if necessary, then screw the nails right into the wooden gate via the bracket’s holes.
3. Take measurements for the top bracket using the cane bolt. Once done with the lower bracket installation, you’ll have to bring out the cane bolt and attach it to the gate to give you an idea of where to place the top bracket - mark the spot using a pencil.
4. Install the top bracket. Start by removing the cane bolt and install the top bracket just as you’ve done with the lower bracket.
5. Install the cane bolt through both brackets.

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

• Hang a batten board

✓ Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

✓ Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

• Form A Pyramid Shape With The Tiles

✓ If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

• Examine The Floor For Level & Walls For Plumb

✓ If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

• The Least Size Of Tiles To Be Used Is Half-Wide

✓ Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.

What Is The Difference Between A Conservatory And An Orangery?

If you’re looking to build an extension for your home, one of the first things that comes to mind is the type of structure that would best suit your property. When it comes to glass extensions there are two major varieties which includes the traditional conservatory and the orangery, but there are usually a lot of confusion over the differences of these two varieties. With the growth in popularity of glazed extensions, the differences between the two structures are becoming more and more thin. However, the main difference between a conservatory and an orangery is the number of glass incorporated. Conservatories are fully glazed structures featuring a low brick base wall, meanwhile orangeries are grand brick structures with with glazed roofs. But as a result of innovations of over the years in glazing, the difference has changed a bit.

Here are some of the major differences between a conservatory and an orangery.

✓ Orangeries are generally best suited to traditional-styled homes or with older property making use of matching stone or brick in construction. Meanwhile for a more recent or modern property, a conservatory will be the better option to add the flair to your property.

✓ Conservatories tend to be larger than orangeries, therefore if you want a smaller extension, an orangery would be your best bet.

✓ Orangeries are typically rectangular in shape and is traditionally a more regular building meanwhile a conservatory can be shaped to suit your needs. With an conservatory, you can get a T-shaped, L-shaped, curved, double ended and lean-to extensions to suit your preference.

✓ An orangery usually possess a flat roof at the edges with a glazed lantern section right at the centre. You can also find more luxurious orangeries having two or more lantern sections. However, when it comes to the roofing, conservatories generally have more options. Some are gabled or pitched, others are lean-to with a plethora of choice to finish off the roof.

An electric range cooker should always be installed by a registered electrician. They will be aware of wiring regulations, what sockets are needed and make sure that your cooker is installed safely and correctly. make sure you book one before your new cooker id delivered!