Find a Shop Fitter you can trust in Broadway.

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Solar panels can be pretty expensive, so require an initial investment. However, a quality solar panel installation can be very financially beneficial, saving you money in the long run. It does this in two main ways.

Firstly, using electricity generated by your solar panels means that you have to use less power from the national grid. Once you’ve bought your solar panels, your solar electricity is essentially free, meaning that you’re saving money by using this instead of power supplied by your energy company. If you want to maximise these savings, invest in a solar battery so you can store unused solar electricity ready for when you need it.

You can also earn money with your commercial solar panels through the Smart Export Guarantee [https://solar-panels.quotatis.co.uk/smart-export-guarantee/]. This is a government scheme that says that all licenced energy suppliers with 150,000 customers or more have to offer a tariff to renewable energy generators. When you generate solar electricity but don’t use it immediately it gets fed back to the grid – the tariff pays you for every kWh of this.

At the moment there’s no minimum tariff that an energy company has to offer – it only has to be above zero. However, many energy companies are competing to offer the best deal, so you can definitely find a tariff that will pay you for all the unused solar electricity you generate.

How Can I Get My Oil Boiler Repaired?

Did your oil boiler just broke down and you’re considering your repair options? Well, you’ve come to the right place! Whenever your oil boiler breaks down, you have two options - repair it yourself or get in touch with a reliable professional. If you lack proper training or experience when it comes to fixing of oil boilers, we’d recommend that you rather hire the services of a trustworthy oil boiler engineer who can guarantee the best results while also saving you time and money that could result from possible costly errors.

However the issue is, not all oil boiler repair services are created equal. The words “expert and “professional are now so cheap that almost, if not all oil boiler repair companies online today make use of those words to qualify themselves. However, when several of them are done delivering their oil boiler repair services you’ll have no other choice than to start questioning their claimed status. In order to separate the boys from the men very early on, a little caution and some research is all that’s needed to know the most reliable company to approach.

To get a good repair company, the first step would be to make sure the company is fully accredited with a professional certification scheme so as to be sure that they’re actually qualified to deliver the service.

Another step you can take is by requesting personal recommendations from family and friends. For a company to be referred by several homeowners in the local area then it must be doing something that’s worth the money invested.

You can as well make use of the internet to get a reliable oil boiler repair company. You can start by visiting the website of the company that manufactured you appliance to identify any recommended repair companies. Go through the companies’ testimonials but do not rely too much on them because in several cases they may not be authentic.

If you’re looking for a reliable or reputable source for your new gas boiler, you definitely won’t find much better than British Gas. Using a big firm like British Gas comes with a plethora of benefits , but of course there are also some drawbacks, with the boiler prices being the main one and biggest turn off for most homeowners. However, just before we delve straight in to the price, let’s look at a thing or two about the big company.

The company, “British Gas are not a boiler manufacturer as you probably would have first imagined. They’re actually a company that specializes in the installation of boilers. As a result, they’re able to install just about any type of boiler you can imagine from any manufacturer. Be it a Worcester Bosch Greenstar 8000 Style or a Baxi 600, they’re able to provide you with the cost of having these boilers installed in your home or property.

Combi boilers are perfect boilers for space-saving and this makes them very popular on the market. They’re also very efficient when it comes to heating water instantly and warm your in few minutes. The price of a new British Gas combi boiler varies on a number of factors. Generally, the installation prices of combi boilers start from £1,800. Therefore, if British Gas are to be competitive with their pricing it should also be around this price.

However, if you have a large house with several rooms with a higher demand for hot water, British Gas will most likely recommend boilers such as Worcester Bosch 440CDi and the likes. Judging from other firms in the market, the price to have these types installed should be in excess of £3,000.

It's not a difficult task to replace an old toilet, as long as you can connect it to an existing branch of the soil pipe. You can cut your water usage significantly by fitting a dual flush toilet mechanism.

Step 1

Follow the manual's guidelines, assemble and insert the flush mechanism. Make sure you include the rubber sealing rings where necessary.

Step 2

Place the large rubber gasket into the flush ingang of the pan.

Step 3

Insert the  bolts through the holes in the cistern, using the rubber and large metal washers supplied.

Step 4

Lift the cistern into the pan so the connecting bolts fit through the holes. The threaded section of the flush mechanism should go through the rubber gasket on the flush entrance of the pan.

Step 5

Fit washers to the connecting bolts, and tighten the wing nuts. Make sure you fit these securely - but don't over-tighten them.

Step 6

check if there are no either pipes or cables below the fixing points. Put the toilet in place, and slide the pan outlet into the flexible connector that's attached to the soil pipe. Then drill some pilot holes into the floor at the fixing points. If it's a solid floor, you'll need to make the holes with a hammer-action drill and plug them.

Step 7

Push plastic protective inserts through the holes in the base of the pan, and insert the retaining screws through and into the floor. If the cistern has fixing holes in the back, attach it to the wall by drilling and plugging. Remember to add rubber washers before you tighten the nuts.

Step 8

Connect the supply pipe for the cold water feed, using a push-fit tap connector.

Step 9

Fit the hinge assembly to the seat, following the manufacturer's instructions.

Step 10

Connect the seat to the pan by securing through the holes at the back, using the screws supplied. Then adjust it to sit in the correct position.

How To Dispose Of Asbestos?

As a homeowner, you certainly wouldn’t like to the word “asbestos” and understandably so. Due to its extremely dangerous fibres, the material was banned in the UK since 1999 and any structure built with it will be heavily fined. However, if you’re presently doing some home improvement project or buying a property that was built before the year 2000, then a chance exists that the property could contain asbestos. So if you’re unlucky to discover asbestos in your property, getting rid of it can be quite simple if you know way around it. In this article, we’ll provide you with some tips on how to dispose of asbestos in your property. Let’s take a closer look!

✓ Careful Handling

If you happen to find asbestos in your property the best thing to do is to call in a reliable specialist who has the proper training and equipment to tackle the project. However, if you decide to handle it yourself, then it’s a must to do this with great care. For instance wearing safety gloves, dust mask, safety goggles and placement of asbestos into plastic bags would be a great idea.

✓ Take It To The Tip By Yourself

To save some money if you have access to a vehicle, then loading the bagged asbestos into your car and driving it to the nearest local tip would be a simple and cost effective alternative. However, you should check with your local authorities before attempting this.

✓ Use A Specialist

Hiring a professional asbestos removal contractor is simply the best way to dispose of asbestos. Their services may be a bit expensive, but they cover up for that in both speed and effectiveness.

✓ Use Your Council’s Asbestos Collection Service

Several councils off this services at a reduced cost. However, they are usually not as quick as a specialist contractor.

If you live in the UK, you’d know by now that no matter what’s happening in the world around us, nothing is going to stop the heat from getting in. And that’s exactly more reason why a well functioning cooling system is more of a necessity than a luxury. Hence, we’ve put together this list to help you avoid common air conditioning mistakes this summer. Let’s take a look!

• Not changing the filter. In the summer when the heat turns up there’s a huge need to change the air filters on a regular basis ( at least once a month). This is due to the fact that your air conditioning system works extra hard and runs all the time during the warmer months. What’s more? If you happen to have pets, a large family or live with an individual who suffers from asthma or allergies, it becomes a lot more important to change your air filters. Plus, a dirty filter is capable of increasing your energy cost within the range of 5 to 15 percent on a monthly basis.
• Not having the right size. When it comes to air conditioning, there’s no one-size-fits-all approach. You simply have to purchase and install the right size for your property which is chiefly determined by the type of the dwelling, the home’s size and other factors.
• Ignoring red flags. Calling in a technician isn’t always the most convenient thing to do especially when life gets a bit busier. However, when you choose to ignore warning signs that something is wrong with your HVAC system, you risk a total breakdown of the unit. What happens is the problem becomes an even more serious issue which will be very costly to repair or at times, replaced.