Find a Solar Panel Installer you can trust in Aboyne.

Solar panels provide an alternative to paying expensive National Grid energy rates, so primarily their first major benefit is helping to reduce bills. Solar PV panels will produce free electricity, whilst solar thermal panels generate heat for hot water and space heating. There are also payment incentives known as the Feed-in Tariff scheme (FITs) (for solar PV) and the Renewable Heat Incentive (for solar thermal) which guarantee a tax-free income for 20 years.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

The more you’re at home during the day, the more you can save on your electricity bill, since solar panels generate electricity during the day. The Feed-in Tariff scheme (FITs) ended in March 2019, but the new Smart Export Guarantee (SEG) pays you, via your energy supplier, for the electricity you export back to the grid. With the savings involved in generating your own electricity and SEG payments, you can expect to save up to £390 per year on your electricity bill.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

Yes – solar panels do work in winter. Contrary to popular belief, solar panels can still work under daylight, even if it's not hot. Of course, they won’t generate as much electricity as they would during the summer months, as the days are shorter, but they will still generate electricity during those daylight hours.

Once you know how solar panels work, it’s easy to understand why solar panels work in the winter. Solar panels are made up of photovoltaic (PV) cells, which are units usually made out of silicon. These cells contain electrons that create energy when light hits them. The cell can then convert this energy into usable electric current and into your system to be used around the home.

Although it might seem strange, solar PV cells can actually work better when it’s cold. Too much heat around the cell can cause it to be inefficient, due to the difference in energy between the energy from the sunlight and the electrons in the solar cell. During cold weather, the difference between them is higher, so more

The higher the energy difference between the two sets of energy sources, the more power that the cell can produce when it’s struck by light. Of course, the downside is that there are fewer daylight hours in the winter, so you’ll still see a drop in energy production – but at least you know that your solar panels are still working efficiently. The other thing to bear in mind is that obstructions like snow and lots of cloud cover will impact the amount of electricity your solar panels will produce. Luckily the UK doesn’t get too much heavy snow, so any snow that does settle on the panels will melt quickly. As for cloud cover, even on exceptionally cloudy days your panels will still generate some electricity – just not as much as they would on a clear day.