Find a Solar Panel Installer you can trust in Acharacle.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.

In theory, you can fit solar panels yourself. In practice, it’s worth leaving it up to the professionals.

If you get DIY solar panels and install them on your roof yourself, you won’t be able to apply for the government-backed Smart Export Guarantee (SEG). The SEG pays you for every unit of electricity you generate and send back to the grid, so it’s a scheme well worth signing up for. However, you must have your solar panels installed by a Microgeneration Certification Scheme (MCS)-registered engineer or company, so you’ll miss out if you install the solar panels by yourself.

The other thing to consider about installing solar panels yourself is that you’re dealing with electricity. Electricity is extremely dangerous if handled incorrectly, so if you don’t have any qualifications in working with electricity you could be putting yourself and your family at risk. Connecting DIY solar panels yourself and doing it incorrectly could mean that you give yourself an electric shock or cause a fire. If your home is damaged due to a fire caused by solar panels you’ve installed yourself, it’s unlikely that your home insurance company would pay out.

Before having a go at installing your own solar panels, do some quick sums to see how much money it could really save you. A 3.5kW DIY solar panel kit will cost around £4,000-5,000. According to the Energy Saving Trust, a home in the South East of England where most occupants are out all day until 6pm would save around £100 a year on their electricity bills. That means that you wouldn’t break even until 40 years, but solar panels last around 25 years on average. However, if you have your solar panels installed by an MCS-registered installer and they cost £4,500, you could save £220 a year including your SEG payments. That brings the payback time to around 20 years.

So although the initial outlay is slightly less when you install solar panels yourself, it’s much better to have them installed by an MCS-registered engineer so you can take advantage of the SEG payments.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

Yes – solar thermal can be used for central heating. Solar thermal panels work by collecting heat from the sun, either through evacuated tubes or flat plate collectors, and transferring that to a heat transfer liquid that heats your hot water. This can then be used to preheat your central heating.

You’ll need a hot water cylinder to store the water that your solar thermal panels heat up. It’s likely that you’ll need an immersion heater or boiler to heat the water further so you can use it for your central heating, and as a back-up during the longest winter months since the solar panels won’t be able to generate as much heat.

In our opinion, it’s best to use your solar thermal panels for hot water rather than your central heating. That’s because you use hot water all year round, whereas you probably won’t have your central heating on in the spring and summer, when the panels can generate the most heat. For central heating, air- or ground-source heat pumps are a great renewable option, and you can even power them with electricity from solar PV panels if you want to be as eco-friendly as possible.

Asides from the fact that solar energy can be converted into electricity with the help of solar panels, there’s also another pretty cool way the sun’s power can be harnessed - solar thermal technologies. These technologies are able to convert sunlight into heat rather than power and these are in fact the very first solar energy products that were commercialized in the United Kingdom. Solar thermal panels, in a similar way to solar PVs, can help in minimizing your carbon footprint while also assisting you to save good money on your energy bills by providing the much needed coverage for your heating needs with the help of a renewable energy source that’s totally free.

Solar thermal panels provides some great benefits which is capable of making all homeowners in the UK consider installing one in their respective homes. Let’s take a closer look at these benefits.

✓ When compared to solar PV panels, they’re a more affordable heating option and also have a shorter payback period.

✓ Solar thermal panels are more efficient than PV panels due to the fact that the heat waves are able to hold more energy than sunlight and also because there’s no electricity transformation process.

✓ Solar thermal panels are able to operate in cold climates, strong wind as well as overcast weather, and make use of an energy storage system.

✓ They can help you save about 600kg of carbon dioxide emissions on an annual basis.

✓ Although most of the solar thermal panel systems come with a warranty usually within the range of 5 to 10 years, they’re able to last up to 25 years. What’s more? The require just a little maintenance, meaning the main cost you’d have to worry about is the cost of installation.