Find a Solar Panel Installer you can trust in Ayrshire.

Just like other major house improvement projects, some specific requirements must be met to allow for the installation of solar panels on commercial buildings. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Fortunately, the installation of solar panels on commercial buildings may be “permitted development which mean you won’t have to apply to the Local Planning Authority for planning permission. There are, however, some important limits and conditions which must be put into consideration in order to benefit from these permitted development rights. Some of the limitations include:

• The solar panels must be installed on a wall or pitched roof that should project at a maximum of 200mm from the surface of the wall or roof slope.
• Equipment placed on a roof should not be within one metre of the external edge of that roof.
• Equipment mounted on a wall must not be within one metre of a junction of that wall with another wall or with the roof of the building
• If the equipment is on the roof of a building, the capacity for generation of electricity across the entire site must not be more than 1 megawatt.
• In the situation whereby the panels are installed on a flat roof, the highest part of the equipment should not exceed one metre above the highest part of the roof.

In general, obtaining a planning permission is very important and as such, you must discuss your position with your chosen installation company before you proceed.

To have your solar panels working at full strength at all times is crucial as this can go a long way to help you reduce your energy bill. In order to achieve this, you simply can’t afford to ignore having them regularly cleaned and free from all sorts of dirt, dust, debris, pollen, bird droppings and the likes. Now it’s quite reasonable to think rain or wind should be able to get the job done, but unfortunately this is not so. What solar panels need is a proper clean which you can decide to do by yourself or call in a qualified professional – the latter which is strongly recommended.

Cleaning of solar panels has to do with working at heights which can be very dangerous especially if you don’t have enough confidence to pull it off. And even if you have zero phobia for heights, solar panel cleaning requires experience as well as some specialized skills and tools possessed by the professionals. However, the question here is, how often should solar panels be cleaned to keep them operating at optimal efficiency?

Well, according to the manufacturers, solar panels should be cleaned twice a year. However, if this is something that you feel is not achievable by you, then you should at least give then an annual clean. The best or most advisable time to do this during the year is at the end of the summer months. This will ensure that you have a fully functioning solar array which is ready and prepared to withstand whatever the cold period throws at you. At the end of the day, you’d have them looking spotless clean while also working at full strength and reducing your energy bills.

There are a few factors that will determine whether it’s worth getting a solar battery. They involve how much electricity you use, how often you’re at home and whether you receive any export payments.

To work out whether it’s worth getting a solar battery, you need to work out how much of the electricity you generate you’re using already. If you’re able to run all your appliances during the day while your solar panels generate electricity, then it sounds like you’re already using your electricity well. It might not be worth you getting a solar battery in this case.

However, if you’re not at home for a lot of the day, then you’ll be missing out on the electricity your panels are generating while the sun’s shining. If you install a solar battery system, you can store the electricity that your panels generate in the battery and use it when you get home. This will help you cut your electricity bills even further.

You’ll also need to consider whether you’re getting paid to export your electricity. If you’re on the Feed-in Tariff scheme (FITs) or receive payments from the Smart Export Guarantee (SEG), you’ll get paid for every unit of electricity you export to the National Grid. Before you decide whether it’s worth getting a solar battery, you’ll need to weigh up whether you’d be better off carrying on exporting your unused electricity rather than storing it to use yourself. If you’re unsure, visit the Energy Saving Trust’s website or speak to an MCS-registered installer who will be able to help you work out which is more cost-effective.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

No – solar thermal doesn’t generate electricity. Unlike solar PV, solar thermal panels harness the sun’s energy and convert it into heat which is then transferred into your home.

You can have evacuated tube solar thermal panels or flat plate collectors; evacuated tubes are thought to be more efficient that flat plate collectors. They both work by using the sun’s rays to heat a transfer fluid, usually made from water and a type of antifreeze, which is pumped to a heat exchanger inside a water tank in your home. The heat from the exchanger heats the water inside your tank, then when the liquid releases its heat it’s transferred back to the collectors to start the whole process again.

You’ll need to use your solar thermal panel system with a boiler, collector or immersion heater. This is so that the water can be stored and used for your hot water and heating, and also because in the UK, people generally need to rely on another source of heating in the winter. There are fewer sunlight hours in the winter months, so it’s not often possible for solar thermal panels to generate enough heat from the sun to get your water up to temperature.

Whatever the time of year it is, you might want to heat the water up further than your solar panels can manage. That’s why you’ll still need a form of traditional hot water heating, but you should see savings on your energy bills. If you’re currently using natural gas, you can expect savings of around £60 per year on your fuel bills, while if you’re using LPG it could be as high as £100 pr year

It’s important to get the right size solar panel system for your commercial property. Solar panels are usually installed on pitched roofs, although they can be fitted on stands on the ground if you have some unused outdoor space. The more panels you install, the more power you’ll generate, but there’s no point buying more panels than you have space for.

Solar panel system sizes are measured in kW. 4-10kW solar panel systems are usually too big for domestic properties but are ideal for smaller commercial properties. Here’s an idea of how many panels and space you’ll need for a few different system sizes:

System size, Number of panels, Area required (approximate)

4kW, 16, 23m²

6kW, 24, 35m²

8kW, 32, 46m²

10kw, 40, 58m²

Bear in mind that solar panels can’t be less than 30cm away from a roof edge, so you’ll need more space than the area that the panels take up.