Find a Solar Panel Installer you can trust in Clwyd.

If you’re thinking about installing a solar system in your home or property, this is probably one of the things you’d like to know before making a purchase decision. Well, you’ve come to the right place! In this post, we’re going to give you a good insight into this to help you make the best informed decision possible moving forward. Let’s take a look!

First and foremost, it must be stated that providing a short and accurate answer to this question is nearly impossible as the amount of time a solar panel will last after dark is influenced by a number of factors. These factors include the size of your solar system, the battery size as well as your power usage. As you would have imagined, batteries are charged when there is excess energy that’s being produced by your solar system but it’s not being incorporated to power your home or property. More often than not, this occurs during the sunlight’s peak periods from about 10am to 2pm.

The time it’ll take for your battery to charge is influenced by the size of your solar system in Kilowatts, the size of your battery as well as the rate in which your system is being used. Your battery can be charged in a day or two, of course unless it’s an over-sized battery for your system.

When the sun sets and your solar panels can no longer directly run your appliances via electricity generation, the battery then kicks in. You will use about 1 to 2 kW’s of power if you’re watching TV, using the oven as well as lights internet etc. in other words, even a small solar panel battery will last all night. However, the same doesn’t apply if you’re having a party with running floodlights, three fridges and air conditioner as the battery will drain a lot faster.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

Are you currently weighting the possibilities of adding a solar system to your commercial building? With lots of commercial property owners in the UK using solar now, many more are gradually coming to terms with the numerous benefits they stand to derive by getting one. Therefore, if you’re thinking about adding the system to your commercial building but do not know where to start, you’ve come to the right place.

In this post, our aim is to help you calculate the number of solar panels you’ll need to power your entire commercial building. Starting from the panels, you can begin by taking into account everything that makes use of power in your commercial building to get a good idea of how many you’ll need.

• To get started, you’ll have to determine the number of watts used by your commercial building. To get this, you simply have to go through your utility bill for kilowatt-hours (kWh). This varies amongst buildings and being able to identify your daily average energy usage will assist you in getting your solar panel needs.
• Once done, you’ll also have to determine the peak sunlight hours - having in mind that the solar panels only work when under direct sunlight. Once determined, you can then multiply the figure in hours by your home’s hourly energy usage and divide by your selected solar panel’s wattage.

In general, a medium-sized commercial building making use of an average amount of electricity will require about 70 average quality solar panels so as to cover its entire electricity needs. These are, however, just averages, so yours could be more or less so getting the idea is vital here.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.

If your solar panels are mounted on your roof and you require a ladder to reach them we would always recommend you get a professional to do the work for your own safety.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

No – solar thermal doesn’t generate electricity. Unlike solar PV, solar thermal panels harness the sun’s energy and convert it into heat which is then transferred into your home.

You can have evacuated tube solar thermal panels or flat plate collectors; evacuated tubes are thought to be more efficient that flat plate collectors. They both work by using the sun’s rays to heat a transfer fluid, usually made from water and a type of antifreeze, which is pumped to a heat exchanger inside a water tank in your home. The heat from the exchanger heats the water inside your tank, then when the liquid releases its heat it’s transferred back to the collectors to start the whole process again.

You’ll need to use your solar thermal panel system with a boiler, collector or immersion heater. This is so that the water can be stored and used for your hot water and heating, and also because in the UK, people generally need to rely on another source of heating in the winter. There are fewer sunlight hours in the winter months, so it’s not often possible for solar thermal panels to generate enough heat from the sun to get your water up to temperature.

Whatever the time of year it is, you might want to heat the water up further than your solar panels can manage. That’s why you’ll still need a form of traditional hot water heating, but you should see savings on your energy bills. If you’re currently using natural gas, you can expect savings of around £60 per year on your fuel bills, while if you’re using LPG it could be as high as £100 pr year

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.