Find a Solar Panel Installer you can trust in Exmouth.

If you want to test your solar panel system to see if it’s working properly or just to see what output it’s giving, you can do this using a multimeter to measure current, or amps, and voltage.

Before you start, you’ll need to find the voltage (v) and current (A) ratings of your panel. You should be able to find them on the back of the panel. You should also make sure that it’s a nice clear, sunny day to get the best readings out of your panel. You should also check that it’s safe to be up on your roof!

To measure open circuit voltage, you’ll need to make sure that your solar panel is completely disconnected from your system’s regulator and battery (if you have one). Angle the panel towards the sun, and ensure that your multimeter is set to measure volts. Measure the voltage between the positive and negative terminals by connecting the negative contact on the voltmeter to the negative on the panel and the positive contact on the voltmeter to the positive on the panel.

Then, you can move on to the short circuit current. Follow the same steps as the open circuit voltage, but ensure that your multimeter is set at 10A to start with.

Only try to test your solar panel if it’s safe to do so. If your roof isn’t accessible without scaffolding or specialist equipment, consider speaking to an MCS-registered solar company about your concerns. They may recommend that they come to service your solar panel system.

If you’re thinking about getting a solar thermal system for your home, it’s normal to consider the possibility of using the system for central heating. So is this viable? In this article, you’ll learn how solar thermal panels can be incorporated for heating. Let’s have a closer look!

Heating and hot water systems, on the average, takes up a sizeable part ( up to 70 percent) of our energy bills. Now take a moment to imagine how cool it’ll be to generate your own hot water for free without having to depend on any supplier which in turn significantly reduces your energy bills. Well, this is exactly the work of central heating systems that are powered by solar. That’s super cool, right? Well, let’s have a look at how this works.

While solar panels generates electricity, solar thermal panels produces heat for hot water production. However, what’s important is the fact that they both make use of the sun’s natural energy to provide us with a free and renewable energy we can use in our homes. Here’s how it works.

Solar thermal panels directed at central heating incorporates the sun’s natural energy to heat water in a storage cylinder which is then available for use at home. These solar thermal panels are exposed to the sunlight by fitting them on the roof of the home. Generally, they’ll include tubes that contains liquid whose job is to collect the heat and then transfer it to a hot water cylinder that’s solar compatible in your home. The heat is generated for free and is also renewable. This is help you save lots of money on oil, gas and even electricity which you purchase to power the cylinder.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

Yes – solar panels do work in winter. Contrary to popular belief, solar panels can still work under daylight, even if it's not hot. Of course, they won’t generate as much electricity as they would during the summer months, as the days are shorter, but they will still generate electricity during those daylight hours.

Once you know how solar panels work, it’s easy to understand why solar panels work in the winter. Solar panels are made up of photovoltaic (PV) cells, which are units usually made out of silicon. These cells contain electrons that create energy when light hits them. The cell can then convert this energy into usable electric current and into your system to be used around the home.

Although it might seem strange, solar PV cells can actually work better when it’s cold. Too much heat around the cell can cause it to be inefficient, due to the difference in energy between the energy from the sunlight and the electrons in the solar cell. During cold weather, the difference between them is higher, so more

The higher the energy difference between the two sets of energy sources, the more power that the cell can produce when it’s struck by light. Of course, the downside is that there are fewer daylight hours in the winter, so you’ll still see a drop in energy production – but at least you know that your solar panels are still working efficiently. The other thing to bear in mind is that obstructions like snow and lots of cloud cover will impact the amount of electricity your solar panels will produce. Luckily the UK doesn’t get too much heavy snow, so any snow that does settle on the panels will melt quickly. As for cloud cover, even on exceptionally cloudy days your panels will still generate some electricity – just not as much as they would on a clear day.

No – solar thermal doesn’t generate electricity. Unlike solar PV, solar thermal panels harness the sun’s energy and convert it into heat which is then transferred into your home.

You can have evacuated tube solar thermal panels or flat plate collectors; evacuated tubes are thought to be more efficient that flat plate collectors. They both work by using the sun’s rays to heat a transfer fluid, usually made from water and a type of antifreeze, which is pumped to a heat exchanger inside a water tank in your home. The heat from the exchanger heats the water inside your tank, then when the liquid releases its heat it’s transferred back to the collectors to start the whole process again.

You’ll need to use your solar thermal panel system with a boiler, collector or immersion heater. This is so that the water can be stored and used for your hot water and heating, and also because in the UK, people generally need to rely on another source of heating in the winter. There are fewer sunlight hours in the winter months, so it’s not often possible for solar thermal panels to generate enough heat from the sun to get your water up to temperature.

Whatever the time of year it is, you might want to heat the water up further than your solar panels can manage. That’s why you’ll still need a form of traditional hot water heating, but you should see savings on your energy bills. If you’re currently using natural gas, you can expect savings of around £60 per year on your fuel bills, while if you’re using LPG it could be as high as £100 pr year

It may be hard to believe with the summers we have in the UK, but there is more than enough sunlight to power solar panels. Solar PV (photovoltaic) panels operate in daylight, rather than needing direct rays from the sun so they’ll work throughout the year.